Avtex W102D User manual

TFT-LCD TV
READ CAREFULLY
BEFORE OPERATION
USER MANUALUSER MANUAL
W102D
W102D

Before connecting the AC power cord to the DC adapter outlet ,make sure the
voltage designation of the LCD TV corresponds to the local electrical supply .
If you are unsure of your power supply , ask your local power company .
Never insert anythingmetallic into thecabinet openings ofthe LCD TV;
otherwise may causethe danger ofelectric shock.
To avoid electric shock, never touch the inside of the LCD TV / adapter.
Only a qualified technician could open the case of the LCD TV/adapter.
Never use your LCD TV/adapter when the power cord has been damaged .
Make sure there is nothing rest on the power cord, and keep the cord away
from the place where people can trip over it .
Be sure to hold the plug, not the cord when disconnecting the adapter from
an electric socket.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
TO PREVENT ELECTRICAL SHOCK.
DO NOT REMOVE THIS COVER. NO
USER- SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol indicates
dangerous voltage
inside the product that
presents a risk of electric
shock or personal injury.
This symbol indicates
important instructions
accompanying the
product.
Please read thismanual carefully before using this product.
IMPORTANT SAFETY INSTRUCTIONS
Openings in the LCD TV/adapter cabinet are provided for ventilation.
To prevent overheating, these openings should not be blocked or covered.
Also, avoid usingthe LCD TV on a bed ,sofa ,rug, or other soft surface. If not,
may block the ventilation openings in the bottom of the cabinet. If you put the
LCD TV in a bookcase or some other airless space, be sure to provide adequate
ventilation.
Do not exposethe LCD TV to extreme temperature conditions or to extreme
humidity conditions.
The apparatus shallnot be exposedto dripping orsplashing and thatno objects
filled with liquids,such as vases,be placed onthe apparatus.

Do not clean the front with keton-type materials (e.g.Acetone ),ethyl alcohol,
toluene, ethy lacid, methyl, or chloride-these may damage the panel.
Locate your DCadapter near aneasily accessibleAC outlet.
If your LCD TV does not operate normally in particular, if there are
any unusual sounds or smells coming from it unplug it immediately and
contact an authorized dealer or service center.
High temperature can cause problems. Don`t use your LCD TV in
direct sunlight, and keep it away from heaters, stoves, fireplaces, and other
sources of heat.
Unplug the DCadapter when itis going tobe left unusedfor a long time .
Toreduce the riskof fire orelectric shock, andannoying interference, use
the recommended accessories only.
If the LCD TV is broken, do not try to repair it yourself. Contact
qualified service personnel.
Unplug your DC adapter from the AC outlet before any service.
Be sure the service technician uses authorized replacement parts or their equi-
valents. Unauthorized partsmay cause fire,electrical shook, orother hazards.
Following any serviceor repair,be sure theservice technician performssafety
checks to certify that your TFT-LCD TV is in a safe operating order.
The apparatus withCLASS I constructionshall be connectedto a MAINS
socket outlet with a protective earthing connection.
IMPORTANT SAFETY INSTRUCTIONS

PANELBUTTON FUNCTIONS
Panel control
6
CONTENT
AV SETUP
AV setup
16
EXTERNAL EQUIPMENT
Connecting diagram
7
LET'S START
Change source operation
11
REMOTE CONTROL HANDSET
Remote buttons
8Battery installation
9
TV MENU SETUP
Picture
TV setting
System
12
13
14 15
Channel edit
DVD OPERATION
Brief introduction
17 Features
18
Compatible disc types
19
VCD, SVCD menuplayback
21 Select track toplay directly
by number buttons 22
Playback
20
Select language/audio
22
Repeat playback 23
Repeat playback of
selected segment
23 Fast playback 24
Play from thedesired position 24 MPEG4 and JPEGfile playing 25
INSTALLATION
Mounting bracket install
1
Can adapter connection
2
Battery pack installation
3
Headrest bracket installation
4
CARD READERAND USB OPERATION
Usage of USBequipment
and 3-IN-1card reader
28

CONTENT
DISPLAY MODE
43
Display mode
SPECIFICATIONS
Specifications
42
DVD FUNCTION SETUP
General setup
30
33
Password setup
Preference setup
32
Video setup
31
Audio setup
30
TROUBLE SHOOTING
TV troubleshooting
40 DVD troubleshooting 41
DVB FUNCTION SETUP
General setup
34
DVB-T setup
35
Video setup
34
FM OPERATION
FM
38 System 39

Figure 1:
Takethe backboard and4 screws fromaccessories, and lie the host machineflat,
with bottom casingfacing upwards. According to thedirection shown in the figure,
make the 4screw holes in the backboard aimat the 4 in the bottomcasing of the
host machine, andthen use 4 screws to fixthe backboard onto the bottom casing
of the hostmachine (shown in the figure 1).
host machine
backboard
Figure 2:
Takeout the headrest bracket from accessories,rip off the magic bandfirstly,
and then makethe face with sponge alongside theheadrest of the car seat,
and the endwith clasp plate face upwards; thenbind the magic band on the
headrest of carseat (shown in figure 2); finallycheck whether the headrest
bracket becomes loose.
clasp plate
headrest bracket
car seat
INSTALLATION
2
HEADREST BRACKET INSTALLATION
When installing thehost machine with backboard onto theheadrest bracket, take
hold of thehost machine with two hands, makethe left and right clasp slots of the
host machine aimat those of the headrest bracketvertically and slide downwards
until a clicksound is heard. Now you still need to uplift it upwards to check whether
it is loose,if not, it means that theinstallation is proper and full.

Figure 3:
Install the hostmachine and headrest bracket onto thecar seat, with the effect
shown in thefigure 4.
When taking outthe host machine, press the claspplate backwards to make the host
machine come loose,and then take the host machinewith one hand.
Clasp
plate
Figure 4:
INSTALLATION
3
Connect car adapter(make sure to use the recommended
accessories only) tothe socket in your car correctly.
Connect the otherend of the car adapter tothe TV DC
input socket, asthe picture show:
The car adapteralso can be used to chargethe
battery pack ifthe battery pack is on .
The car adaptercan only be connected to DC
12V socket inyour car, otherwise may cause
damage to thecar adapter or the TV. Please pay
attention to this.
CAR ADAPTER CONNECTION
When use theTV in a car, you can use the car adapter
instead of thebattery pack, to save energy ofyour
battery in orderto make it work longer.

BATTERY PACK
1. Installing batterypack
Place this unitto the center of the back,then slide the battery pack tosecure it as the
direction (figure ).
When the batterypack is power on, the orangeindicator will flash for about 1 second,
indicating that thewhole charging system is powered on .
After entering chargingprocess, the red indicator is always on, which means that the
battery pack isbeing charged.
BATTERY PACK INSTALLATION
4
1
Please use theadapter provided, connect to the DC IN socket ofthe battery pack to
charge it (figure ). When the battery is onthe TV, you also can charge it while LCD
TV is working(figure ).
3
4. Recharging battery pack
2
3. Remove battery pack
Push the batterypack as the direction shown in figure , thentake it out.
34
2
2. Use battery
If the batteryis full, you can use this LCD TV freely.
If the batterypack is installed correctly, the indicator on the TV will turn red. If not, please
check whether thebattery is full or be installed correctly.
When the voltageof the battery is lower than 5.8V, the TV set will turn off automatically.
You have to charge the battery tomake it work again.
When use thebattery pack, it may feels a bit warm, that's OK.
Button
1
4
If the batterypack is on the LCD TV, whether the TV is inSTANDBY mode or POWER
ON mode, itcan charge the battery. In POWER ONmode, a battery sign will be
displayed on thescreen to say the battery isbeing charged.
" "
Indicator

Please use the recommended adapter to recharge it, otherwise it will damage the battery
pack.
BATTERY PACK
After battery packis fully charged, the green indicatoris always on ,which mean that
the battery packhas been fully charged, so pleaseunplug the power cord.
If the indicatorhas other displays after power-on ofthe system, it means the battery
pack has troubles.Please unplug power cord and contactthe appointed servicing
personnel.
If the rechargeablebattery hasn't been used for a long time, the quantity of electricity
will be toolow and the LCD TV cannot power on,so please chargethe battery first.
Danger of explosionif battery is incorrectly replaced.
Replace only withthe same or equivalent type.
CAUTION:
5
New battery orbattery stored for a long timemay take more time to charge.
5. Cautions on battery pack
This LCD TV's battery pack is rechargeable. It should be fully recharged before use.
Do not dispose it in fire or water. Do not heat the battery pack.
Do not use it in high ambient temperature or near a heat source.
Do not connect the positive and negative polarities with a metal object.
The operating temperature of the battery pack is 0~35
Over-charge: the batteryis over-charged or over-saturated, so that the voltage of the
battery exceed theupper limit voltages,(For lithium batteries, the upper limit voltage
for a singlebattery is 4.25V).
Non-saturated charge: the indicator indicates that charging has been always onbut
the battery doesnot turn to the saturated status after regular duration of charging .
Please remove the battery pack if you do not intend to use this LCD TV for an extended
period of time. (Power is still consumed although this LCD TV is turned off. Therefore,
the battery pack may be damaged due to excessive discharging.)
Self-discharge: discharge of batterydue to the static power consumptionof the
peripheral circuit, dampair and self-structure.
Over-discharge self-discharge of thebattery too long time results inthat the voltage
of the batteryare lower than the lower limitvoltage.(For lithium batteries, the lower limit
voltage for asingle battery is 4.25V ) Notethat to avoid over-discharge of thebattery in
the case of long disuse ofthe battery, regularly chargethe battery, so thatthe voltage
of the batteryis maintained between 3.6V and 3.9V.Trickle charge: when the voltages
at both polesof the battery are lower than3.0V(for lithium battery ),low current will be
employed to chargethe battery at 0.01C(C indicates thebattery capacity)for about
15~30 minutes.

6
PANEL BUTTON FUNCTIONS
PANEL CONTROL
Indicator( )Indicator is redwhen in standby mode, green whenworking normally.
1
IR sensor window
2
Front panel
Top panel
3STANDBY (Toswitch from standby mode to power-onmode)
4SOURCE (Select input source)
5CH-/+ (Increase or decreasechannel number/to move selected menu item)
10 (Eject button)
6VOL-/+ (Increase or decrease volume/characteristics)
7SETUP (Enter or exit setup menu)
9
(Stop button)
8(Play/puase button)
345678910
1
11
12
13
14
15
16
17
19
20
Left panel
11 USB jack
12 MEDIA CARDsocket
13 12Volt DCpower input socket
14 AV audio video input jack
15 AV audio video output jack
17 Headphone jack
18 FM antenna input
Right panel
20 Disc in/out door
16 Headphone jack
18
RF input terminali
19
2

DVD or VCR player
NOTE
CONNECTING DIAGRAM
You should insert any interconnecting cables BEFORE plugging in the power cord.
EXTERNAL EQUIPMENT
The left of TV set
7
RL
VIDEO
RL
VIDEO
TV

8
REMOTE BUTTONS
REMOTE CONTROL HANDSET
STANDBY
1Switches between standbymode and power-on
mode.
VOLUME+/-
3
Increases or decreasessound amplitude
CHANNEL+/-
4
Steps up/down programnumbers.
RETURN
5
Toswap between a previous program andthe
current program (onlyvalid in TV mode.)
SETUP
7
Display setup menu,different in TV and DVD
mode.
B.L ON/OFF
8
Toturn on/off the screen ( only valid in radio
mode).
16 AUDIO
In DVD mode,to change sound decode mode like
DTS or Dolby.
In DVB mode,to change sound track between left,
right and stereo.
PICTURE
2
Set picture mode:Dynamic, Soft, User, Standard.
1
2
3
5
8
11
7
10
6
17
4
9
14
9CARD/DISK
Toswitch in card reader, DVDand USB modes
(only valid inDVD mode).
11 STOP
Tostop playing a DVD (only valid in DVD mode).
10 DVD MENU
Display DVD menuor open/close PBC;
In DVB mode,long press to auto scan .
13
12
16
RATIO
6
Switch the picturemode in 4:3 or 16:9.
12
Switch between TV and radiomodes (valid in
DVB mode).
TV/
17 ANGLE
Change camera angle,JPEG
playback modes switch.
13 EPG/
Todisplay the program guide (valid in DVB mode)
/Toselect the previous chapter or track (valid in
DVD mode).
REPEAT
Torepeat playback (valid in DVD
mode ).
18
15
18
FAV./
In DVB mode,open favourite channel list/Toselect
the next chapteror track (valid in DVD mode).
14
ANT. ON/OFF
In DVB mode,turn on/off antenna power supply.
15

9
REMOTE CONTROL HANDSET (contd)
EJECT
Disc in/out ,validin DVD mode.
17
MUTE
Sound mute button.
18
TWO-DIGIT button
20
Switches between oneor two-digit program
numbers.
DISP
25
Display or hidechannel information / Display
or hide discinformation.
UP/DOWN cursor
24
Tonavigate upward/downward in the menu.
SOURCE
21
Select input source:TV, DVD, AV, DVB, FM.
OK button
22
Toconfirm a selection/item in menu.
LEFT/RIGHT cursor
23
Tomove left/right or adjust a selecteditem
in menu.
23
27
18
19
20
21
22
24
26
25
28
30
31
33
32
17
Number buttons
Toselect program number.
19
GOTO
32
Toplay a DVD from a certaintime-point (only
valid in DVDmode).
SUBT
30
In DVD/DVB modeselect the subtitle language.
Switch to JPEGdisplay mode(only valid in DVD
mode).
LANG
31
Switch the outputlanguage (valid in DVD/DVB
mode).
29
INFO/
28
Todisplay the information about channel and
program (valid inDVD and DVB mode)/Fast
backwards DVD playback(only valid in DVD
mode ).
A-B
33
Torepeat play a DVD segment (onlyvalid in
DVD mode).
29
Tofast backward playback (valid in DVDmode).
26
Pauses playing/steps playbackin pause mode
(only valid inDVD mode) .
27
Toplay normally, valid inDVD mode.

10
BATTERYLIFE
NOTES
CAUTION
Please put batteryin the place children cannot touch.If swallow by accident, please
contact with thelocal doctor immediately.
BATTERY INSTALLATION
REMOTE CONTROL HANDSET
When installing battery, please make the two polaritiesof battery accord with the two polarities
inside the batterycase (positive upward, negative downward), as the following figure:
12
Step 1: Push the button toward left. Step 2: Pull the battery holder out.
CR2025CR2025
Generally speaking, the battery can beused for one year. Butthe detailed battery life
and usage times are related tothe remote control operation.
If the remote control is stillinvalid when near to the unit,please replace the battery.
Do not charge the battery, short-circuit, disassemble, heat or throwit into fire.
Take care notto fall and beat the remote control, which willdamage the remote control
or cause function trouble.
Please use CR2025 battery.
Do not userechargeable battery .
If the batteryof remote control will not be used for a long time, please take it out.
Please confirm whether accessories have poweradaptor.
Please make sure to use poweradaptor in specification range, otherwise itwill
cause trouble.
POWER ADAPTOR INSTALLATION
Step3:Insert one 3VOLTAGE LITHIUM BATTERY matching the -/+ polarities of the battery to
the -/+ marks inside the battery compartment,as the bitmap.

PICTURE
LET'S START
11
INDICATOR
STANDBY
After the unithas been suitably placed / fixed,on the desk or on yourcar, and all cords are
connected for power, input and output .
If your unitis not fixed with the batterypack, connect the adapter to theLCD TV, the unitwill
go into standbymode, and you can see theindicator get into red.
If your unitis fixed with the battery pack,and the quantity of electricity ishigh enough, the
unit will goto standby mode, indicator turn red.If not, please check the batterypack or contact
authorized service department.
CHANGE SOURCE OPERATION
You can change theinput source from the source menu.Press [SOURCE] button on unit or
[SOURCE] key onremote control to show the menu on screen.
The current sourceitem is highlighted. Press [ ]buttons on the remote control, or [CH+/
CH-] key onthe top panel of LCD TV to select your desired mode. Press the [ ] or [OK]
button to confirmyour choice .
STANDBY
TV
DVD
AV
DVB
FM
What you shoulddo next is, press the STANDBY key on the top panel of the TV,or [STANDBY]
button on theremote control to make the unitswitch to power-on mode then you will see the
LED indicator turngreen. Now you can enjoy themany features of your new product.

Item
BRIGHTNESS
Toadjust brightness
CONTRAST Toadjust contrast
SATURATION
Toadjust color saturation
This product can store up to 100-channel programs (0 99). You can scan and
store all the channels through manual or automatic mode.
In TV mode, press [SETUP]button on theremote control or top panel andmenu will show
as follows:
Through pressing [ ] button onthe remote control,
you can selectmain menu sections(main menu
sections consist of
. Press [ ] or [OK]button to enter
this menu section.
" PICTURE ", " TV SETTING ",
" SYSTEM ")
Press [ ]button on the remote control toselect
the item, andthen press [ ] button to adjust
parameter value. Press[SETUP] button to save
your selection andreturn to main menu sections.
Select " "and menu will show as right:
Press [ ]button to select items and [ ]
button to adjust.
TV MENU SETUP
Description
SHARPNESS Toadjust picture sharpness
TINT Toadjust picture tint, only valid inN 3.58/N 4.43/PAL60 and display
mode with V-scanning frequency equal 59.94
12
PICTURE
SELECT RETURN SETUP
PICTURE
BRIGHTNESS 50
CONTRAST 40
SATURATION 50
SHARPNESS 34
TINT 50
ENTER OK
PICTURE MODE STANDARD
COLOR TEMP STANDARD
SELECT RETURN SETUP
PICTURE
BRIGHTNESS 50
CONTRAST 40
SATURATION 50
SHARPNESS 34
TINT 50
PICTURE MODE STANDARD
COLOR TEMP STANDARD
ADJUST
PICTURE MODE Can be changedbetween: USER , STANDARD , DYNAMIC
and SOFT .
" " " " " "
" "
COLOR TEMP Toselect a color temp between : , COOL WARM ."STANDARD " " " and " "

Select " "and menu will showas follows:
TV MENU SETUP
13
TV SETTING
Press [ ]button to selectitem and press [ ] buttonto adjust .
TV SETTING
SOUND SYSTEM
COLOR SYSTEM
FINE TUNE
MANUAL SEARCH
AUTO SEARCH
SELECT RETURN SETUP
ENTER OK
CHANNEL 2
CHANNEL EDIT
AUTO
I
136.20MHZ
Description
FINE TUNE
AUTO SEARCH
CHANNEL EDIT
COLOR SYSTEM Can be changedbetween: "Auto", "PAL" and "SECAM".
SOUND SYSTEM Can be changedbetween:"BG", "DK", "I" and "L" .
Toscan programs and store all ofthem automatically.
Toenter a submenu to set channelskip and channel swap.
Please refer thenext page.
NOTES
Which COLOR SYSTEM mode and SOUND SYSTEM mode to useis related to your
local TV broadcasting system.
""""
SECAM system isonly used by some European countriesand districts, such as France.
If the local system isSECAM L, the color system must be selected as "SECAM" and sound
system must be selected as "L".
Item
Adjust current channelfrequency accurately to make the sound
and picture effect better.
CHANNEL
MANUAL SEARCH
Tochange the channel number.
Toscan programs by manual.

CHANNEL
SKIP
SWAP
Toselect current channel .
Toselect "ON" or "OFF ", youcan select "ON " to make current
channel unaccessible whileusing [CH+/-] button to browse
channels.
Press [ ]button to select the channel, andpress [OK] button to
swap the channel.
Description
Item
14
TV MENU SETUP
TV SETTING
SKIP
SWAP
CHANNEL 2
OFF
38
SELECT RETURN SETUP
ADJUST
during the searching,you can press [SETUP] button tostop.
CHANNEL EDIT

TV MENU SETUP
Press [ ]to select " " item and press [ ]button to enter the following section:
15
SYSTEM
You can setup somesystem configuration here.
Description
TRANSPARENCY
SLEEP
RATIO
RESET
Tochange transparency ofOSD.
Toreset all values to default.
Press [ ]button to selectitem and press [ ] buttonto adjust or activate.
Item
SYSTEM
SLEEP
RATIO
RESET
SELECT RETURN SETUP
ENTER OK
TRANSPARENCY LEVEL 2
0
16 : 9
LANGUAGE ENGLISH
LANGUAGE Select OSD language.
Turn offthe TV after certain minutes automatically, the time you
can set isbetween: Off~240Min.
Set the TV image ratio 4 : 3 or 16 : 9.
STANDBY: 59S
NOTE
If you haveset the sleep time , once the time is less than 1 minute there will be a remind
signal display on the screen :
At present ifyou want to cancel the sleep function, please press [SETUP] button on
remote control.