AVYCON AAVC-BH71F User manual

IR BULLET CAMERA
Specification
Composition
Model
Image Sensor
Horizontal
Resolution
Effective
Pixels
Day/Night
Functionality
Lens Type
# of IR LED’s
IR LED’s
Distance
IR Power On
Scanning System
Sync System
Electronic Shutter
(sec.)
Main Video Output
S/N Ratio
Gamma
Correction
ESC
Gain Control
Weight (g)
Storage
Temperature
Operating
Temperature
Power Consumption
Input Voltage
IMPORTANT INFORMATION:
● Must use specified and regulated 12VDC
power supply.
● Must use correct DC type plug for power lead. If
cables coming out of the camera are spliced,
Warranty will be voided.
● Do not face the camera directly to a strong light
as it will damage the CCD and cause malfunction-
ing of the camera.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful interfer-
ence, and (2)this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and use in accordance with the instruc-
tions, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause interference, in which
case the user will be required to correct the interference at their own expense.
WARNING: Changes or modifications not expressly approved by the manufac-
turer could void the user’s authority to operate the equipment.
CAUTION: When this camera is installed near equipment, like a wireless
communication device that emits a strong electromagnetic field, some irregu-
larity such as noise on the monitor screen may happen.
Regulatory Notice
Warning
*Design and specifications are subject to change without prior notice.
1.
2.
3.
Color Weatherproof 1000TVL IR Bullet Camera
AVC-BH71F / AVC-BH71F-W
AAVC-BH71F / AVC-BH71F-W
AVC-BH71F / AVC-BH71F-W
Installation Manual
1/3” SONY 1.4 Megapixel CMOS Sensor
1000 TV Lines (720P)
[NTSC] 1305(H) x 1094(V)
YES
3.6mm Fixed Lens
￠5 x 24
Up to 60 ft
CDS Auto Control
2:1 Interlace
Internal
1/60 ~ 1/100,000(N)
1.0 Vp-p Composite, 75Ω
More than 52dB (AGC Off)
0.45
Internal
AGC (Auto)
800 g
22°F ~ 140°F (-30°C ~ 60°C) Max. 95% RH
23°F ~ 113°F ( 5°C ~ 45°C)Max. 95% RH
12VDC (+/-10%) / 500mA
Assembly & Mounting Accessories
12VDC

Disclaimer
● While every effort has been made to ensure that the information
contained in this guide is accurate and complete, no liability can be
accepted for any errors or omissions.
● Manufacturer reserves the right to change the specifications of the
hardware and software described herein at any time without prior notice.
● No part of this guide may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language in any form, by
any means, without prior written permission of Manufacturer.
● Manufacturer makes no warranties for damages resulting from
corrupted or lost data due to a mistaken operation or malfunction of the
cameras, peripheral devices, or unapproved/unsupported devices.
Basic Connection
Introduction
ABOUT THIS MANUAL
Thank you for purchasing our camera.
Before installing and using this camera, please read this
manual fully and carefully, and be sure to keep it handy for
later use.
KEY FEATURES
12VDC Power Supply
DVR / Monitor
Polarity：
Power:
Video:
Video
Power
Precautions
Do not install the camera in extreme temperature conditions.
Operate the camera under conditions where temperatures are within 23°F ~ 113°F
(-5°C ~ 45°C). Especially be careful for ventilation under high temperature.
Do not install the camera under unstable lighting conditions .
Severe lighting change or flicker can cause the camera to work improperly.
Never use the camera close to a gas or oil leak.
It can cause malfunctions to occur.
Do not disassemble the camera.
There are no user repairable parts inside.
Do not drop the camera or subject them to physical shocks.
It can cause malfunctions to occur.
Never keep the camera face to strong light directly.
It can damage the CCD and cause malfunctions to occur.
Note
If the camera is exposed to spotlight or object reflecting the strong light, smear or
blooming may occur. Please check the power whether it satisfies the normal
specification before connecting the camera.
Camera
Troubleshooting
If you have trouble operating your camera, refer to the following
If the guidelines do not enable you to solve the problem, contact an authorized technician.
Installation
Dimensions (mm)
The image does not
appear on the screen. * Check the power source for the monitor and camera and
ensure that the voltage and polarity are properly connected
and being supplied correctly.
The image on the screen is
dim. * Check if the front glass is dirty, clean the glass with a
soft, clean cloth.
* Check the power source for the camera and ensure that
enough voltage is supplied.
The camera does not work
properly, the surface of the
camera case is hot, and
black line appears on the
screen.
* Check if you have connected the camera to a proper
power source and if there is no problem with the power,
turn the unit off immediately and seek assistance from
authorized technician.
The screen blinks a lot. * Check if the camera is pointed toward the sun or a
fluorescent lamp.
* Adjust the angle or location of the camera if too much
light is coming into the screen.
FRONT SIDE
1/3” SONY 1.4 Megapixel CMOS Sensor
1000 TV Lines (720P)
3.6mm Fixed Lens
True Day/Night Functionality (ICR)
True Night-vision with built-in IR LED’s
24 IR LED’s (up to 60 ft IR distance)
3D-DNR, WDR, Digital Zoom, Smart IR
12VDC Single Voltage
1. Locate and choose the desired position where the camera will
be mounted.
2. Disassemble the mounting-plate (the plate with three holes)
from the base.
3. Mark three holes according to the mounting plate placement.
4. Drill three holes, then insert anchors into the drilled holes.
5. Attach the camera base to the ceiling or wall using the
supplied three screws.
6. Draw out power / video wires to the connecting places.
7. Assemble the camera back to the mounting-plate and lock it
by using the locking screw located between the mounting
plate and the camera.
8. Loosen the locking screws per desired angle and adjust them.
9. Combine each bracket part, lock and tighten each section by
using the supplied L-wrench.