AXIOMTEK GOT5100T-832 User manual

GOT5100T-832
All-in-One
10.4”SVGA TFT Fanless Touch Panel Computer with
Intel®AtomTM N2600 Processor Onboard
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information. Axiomtek
Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and
any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time without
notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the
prior written permission of Axiomtek Co., Ltd.
Copyright 2012 Axiomtek Co., Ltd.
All Rights Reserved
Sep.2012, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The GOT5100T-832 does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the GOT5100T-832 before any installation. Be sure both
the system and external devices are turned OFF. A sudden surge of power could ruin
sensitive components that the GOT5100T-832 must be properly grounded.
4. The brightness of the flat panel display will be getting weaker as a result of frequent
usage. However, the operating period varies depending on the application environment.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen. The GOT5100T-832 comes with a
touchscreen. Although the touchscreen is chemical resistant, it is recommended that you
spray the liquid cleaner on a cloth first before wiping the screen. In case your system
comes without the touchscreen, you must follow the same procedure and not spray any
cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen. Scratches on the touchscreen
may cause malfunction or internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration. When assembling the
GOT5100T-832, make sure it is securely installed.
8. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel®and Atom™are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties and registered brands of their respective
owners.

iv
Table of Contents
Disclaimers..................................................................................................................................ii
Safety Precautions...................................................................................................................... iii
CHAPTER 1 INTRODUCTION........................................................................................................1
1.1 General Description...................................................................................................1
1.2 Specifications.............................................................................................................2
1.2.1 Main CPU Board........................................................................................................2
1.2.2 I/O System .................................................................................................................2
1.2.3 System Specification..................................................................................................3
1.3 Dimensions................................................................................................................4
1.4 I/O Outlets..................................................................................................................6
1.5 Packing List................................................................................................................7
CHAPTER 2 HARDWARE INSTALLATION...................................................................................9
2.1 CF card Installation....................................................................................................9
2.2 Serial Ports Interface ...............................................................................................10
2.2.1 COM1&COM2 Connector........................................................................................11
2.3 Ethernet ...................................................................................................................12
2.4 Mountings –Panel/Wall/Desktop/VESA..................................................................13
2.4.1 Panel Mounting........................................................................................................13
2.4.2 Wall-Mounting..........................................................................................................14
2.4.3 Desktop-Mounting....................................................................................................14
2.4.4 VESA-ARM Mounting...............................................................................................16
2.5 HDD Installation.......................................................................................................18
2.6 DRAM Installation ....................................................................................................20
2.7 Wireless LAN Card Installation................................................................................22
CHAPTER 3 AMI BIOS SETUP UTILITY .....................................................................................25
3.1 Starting.....................................................................................................................25
3.2 Navigation Keys.......................................................................................................26
3.3 Main Menu ...............................................................................................................27
3.4 Advanced Menu.......................................................................................................28
3.5 Chipset Menu...........................................................................................................35
3.6 Boot Menu................................................................................................................37
3.7 Security Menu..........................................................................................................38
3.8 Exit Menu.................................................................................................................39
CHAPTER 4 DRIVERS INSTALLATION ......................................................................................41
4.1 System.....................................................................................................................41
4.2 Touch Screen...........................................................................................................42
4.2.1 Specification.............................................................................................................42
4.2.2 Driver Installation- Windows 7 .................................................................................42
4.3 Embedded O.S. .......................................................................................................45
4.3.1 WES 7......................................................................................................................45
4.3.2 Windows CE.NET 6.0..............................................................................................45

GOT-5100T User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the GOT5100T-832.
Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT5100T-832 is a fan-less and compact-size touch panel computer, equipped with a 10.4”
TFT LCD display and low power consumption Intel○RAtomTM N2600 1.6GHz processor with FSB
533MHz. The GOT5100T-832 supports Windows®7 32-bit,, WES 7. The panel computer
provides a Mini card slot for wireless module. Its excellent ID and friendly user interface make it a
professional yet easy-to-use panel computer. The GOT5100T-832 is an ideal for space-limited
applications in factory automation, machine maker operating systems, building automation, and
more.
GOT5100T-832: 10.4”TFT SVGA Fanless Touch Panel Computer
Reliable and Stable Design
The GOT5100T-832 adopts a fanless cooling system, which makes it suitable for
vibration environments.
Embedded O.S. Supported
The GOT5100T-832 not only supports Windows® 7 32-bit, but also supports embedded
OS, such as WES 7. For storage device, the GOT5100T-832 supports
CompactFlash™card(optional) and 2.5” SATA device.
Industrial-grade Product Design
The GOT5100T-832 has an incredible design to be used in different industrial
environments.
The front bezel meets the IP65/NEMA4 standard.
For connecting other devices, the GOT5100T-832 also features several interfaces: USB,
Ethernet, and RS-232/422/485.

GOT5100T-832 User’s Manual
Introduction
2
1.2 Specifications
1.2.1 Main CPU Board
CPU
Intel○RAtomTM N2600 1.6GHz processor onboard
System Chipset
Intel○RNM10 Express
BIOS
America Megatrends BIOS
System Memory
One 204-pin DDR3 800MHz SO-DIMM socket
Maximum memory up to 2GB
1.2.2 I/O System
Standard I/O
1x RS-232/422/485, 1x RS232
4x USB 2.0
Ethernet
2x 10/100/1000Mbps Ethernet
Audio
One Line-out
Expansion
1 x PCIe mini card(optional)
Storage
One 2.5”SATA HDD
One slot for CompactFlash™ (optional)
Power connector
GOT5100T-832 : DC power 10~30VDC (phoenix type)
GOT5100T-832-J : AC 100~240V to DC 12V adapter(Screw type)

GOT-5100T User’s Manual
Introduction
3
1.2.3 System Specification
10.4”TFT LCD
Heat Dispensing Design
Disk drive housing:
One 2.5”SATA drive
Net Weight
1.8 Kgs (3.96 lb)
Dimension (Main Body Size)
292.5x 45.8 x 235.8mm
Operation Temperature
0℃to 50℃(with W.T. DRAM/HDD in airflow condition)
Relative Humidity
10% to 95% @ 40℃, Non-Condensing
Vibration
5 to 500 Hz, 2.0 G random for SSD
5 to 500 Hz, 2.0 G random for CF card
Power input
10~30VDC with phoenix power connector
External 60W AC Adapter
—Power Input: 100VAC to 240VAC
—Power Output: 12VDC, Max. 5A
NOTE:All specifications and images are subject to change without notice.
NOTE:If the operation temperature is higher than 35 ℃ , the wide temperature DRAM and HDD
are recommended to be used o the device.

GOT5100T-832 User’s Manual
Introduction
4
1.3 Dimensions
This diagram shows you dimensions and outlines of the GOT5100T-832.

GOT-5100T User’s Manual
Introduction
5

GOT5100T-832 User’s Manual
Introduction
6
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT5100T-832.

GOT-5100T User’s Manual
Introduction
7
1.5 Packing List
When you receive the GOT5100T-832, the bundled package should contain the following items:
GOT5100T-832 x 1
Panel Mount Kit x 6
Driver CD x1
Wall-Mount Kit x1
HDD Mylar x 1
Power Adapter & power cord (for GOT5100T-832-J)
If you can not find the package or any items are missing, please contact AXIOMTEK distributors
immediately.

GOT5100T-832 User’s Manual
Introduction
8
MEMO:

GOT5100T-832 User’s Manual
Hardware Installation
9
CHAPTER 2
HARDWARE INSTALLATION
The GOT5100T-832 provides rich I/O ports and flexible expansions for you to meet different
demand. The chapter will show you how to install the hardware. It includes:
CompactFlash™Card
Serial Port
Ethernet
Mounting Way
Hard disk
Dram
Wireless LAN Card
2.1 CF card Installation
The GOT5100T-832 provides one CF slot for users to install CompactFlash™card. Please refer
to the following instructions for installation:
Step 1 Turn off the system, and unplug the power cord.
Step 2 Find out the cover on the side of the system.
Step 3 Locate the CompactFlashTM socket, and insert the card into the socket.

GOT5100T-832 User’s Manual
Hardware Installation
10
2.2 Serial Ports Interface
The GOT5100T-832 has two onboard serial ports, COM1 (RS-232/ 422/ 485) and COM2 (RS-
232).
The following table shows you the pin assignments of this connector:
The following table shows you the pin assignments of this connector:
Pin
Signal
Pin
Signal
1
Data Carrier Detect (DCD)
6
Data Set Ready (DSR)
2
Receive Data (RXD)
7
Request To Send (RTS)
3
Transmit Data (TXD)
8
Clear To Send (CTS)
4
Data Terminal Ready (DTR)
9
Ring Indicator (RI)
5
Ground (GND)
In addition, COM1 can be set for RS-232/422/485 by jumper. The jump setting is listed as below:
Description
Function
Jumper Setting
COM 1
RS-232 (Default)
JP9
JP7
JP8
RS-422
JP9
JP7
JP8
RS-485
JP9
JP7
JP8

GOT5100T-832 User’s Manual
Hardware Installation
11
2.2.1 COM1&COM2 Connector
The COM1 and COM2 is a standard DB-9 connector. This connector is equipped with +5V level
power capability on DCD and +12V level on RI by setting JP10 and JP11. The pin assignment of
RS-232/RS-422/RS-485 is listed on the following table. If you need COM1 port to support RS-422
or RS-485 mode, please refer to Jumper Settings
COM1(SBC87832)
1 5
6 10
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
N.C
4
DTR
RX-
N.C.
5
GND
No use
No use
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use

GOT5100T-832 User’s Manual
Hardware Installation
12
2.3 Ethernet
The GOT5100T-832 is equipped with two high performance Plug and Play Ethernet interfaces, full
compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Pin
Signal
1
2
3
4
5
6
7
8
RJ-45
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination

GOT5100T-832 User’s Manual
Hardware Installation
13
2.4 Mountings –Panel/Wall/Desktop/VESA
There are several mounting ways for the GOT5100T-832, Panel, Wall, Desktop and VESA
mountings.
2.4.1 Panel Mounting
The GOT5100T-832 is designed for panel mount application. A set of standard mounting kit are
bundled with the system package that you can use it to mount the GOT5100T-832.

GOT5100T-832 User’s Manual
Hardware Installation
14
2.4.2 Wall-Mounting
The GOT5100T-832 is designed for Wall mounting application. Please refer to the following steps:
Find out the screws as marked on the back side of chassis.
2.4.3 Desktop-Mounting
The GOT5100T-832 is designed for desktop mounting application. Please refer to the following
steps:
Step 1 Find out the screws as marked on the back side of chassis.

GOT5100T-832 User’s Manual
Hardware Installation
15
Step 2 Assemble the desktop stand to the chassis, and fix the screws.

GOT5100T-832 User’s Manual
Hardware Installation
16
2.4.4 VESA-ARM Mounting
Step 1 Find out the screws as marked on the back side of chassis.
Step 2 Assemble the VESA-ARM to the back side of the chassis, and fix the screws.