AXIOMTEK SBC82810 Series User manual

SBC82810 Series
Pentium® M All-in-One
Half-size CPU Card
with DualView display and SATA supported
User’s Manual

ii
Disclaimers
The information in this manual has been carefully checked and is believed
to be accurate. Axiomtek Co., Ltd. assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
Axiomtek assumes no responsibility for any inaccuracies that may be
contained in this document. Axiomtek makes no commitment to update or
to keep current the information contained in this manual.
Axiomtek reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission
of Axiomtek Co., Ltd.
©Copyright 2006 by Axiomtek Co., Ltd.
All rights reserved.
Novenber 2006, Version A2
Printed in Taiwan

iii
ESD Precautions
Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic
discharge, observe the following precautions:
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
Before handling a board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. This helps to
discharge any static electricity on your body.
Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
AXIOMTEK is a trademark of Axiomtek Co., Ltd.
MS-DOS and Windows are trademarks of Microsoft
Corporation.
PHOENIX-AWARD is a trademark of Award Software. Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties
and registered brands of their respective owners.

iv
Table of Contents
Disclaimers............................................................................ii
ESD Precautions..................................................................iii
C h a p t e r 1..............................................................................1
1.1 Specifications .......................................................2
1.2 Utilities Supported................................................4
C h a p t e r 2..............................................................................5
2.1 Board Layout and Fixing Holes...........................5
2.2 Placement..............................................................7
2.3 Jumper Settings....................................................8
2.3.1 Audio Output Select Jumper: JP1...............................9
2.3.2 Watch dog Reset setting:JP2.......................................9
2.3.3 Reset CMOS Jumper: JP3............................................9
2.3.4 LVDS Voltage Setting : JP4...........................................9
2.3.5 CompactFlash Power Setting: JP5..............................9
2.3.6 COM2 Mode Select for Type: JP6; JP7; JP8.................10
2.4 Connectors..........................................................11
C h a p t e r 3............................................................................13
3.1 Microprocessors.................................................13
3.2 BIOS.....................................................................13
3.3 System Memory ..................................................13
3.4 I/O Port Address Map .........................................14
3.5 Interrupt Controller.............................................15
3.6 IDE Interface Connector.....................................16
3.7 Display Interface.................................................18
3.7.1 Graphic Controller.....................................................18
3.7.2 Features ......................................................................18
3.7.3 DVI/CRT Connector :CN17........................................19
3.7.4 LVDS Power Connector: CN16..................................20
3.7.5 24bit LVDS Connector: CN13/CN14 .........................20
3.8 Floppy Disk Controller .......................................21

v
3.9 Parallel Port Interface.........................................21
3.10 Serial Port Interface............................................22
3.11 Keyboard and PS/2 Mouse Connector..............23
3.12 USB Connector...................................................24
3.13 Ethernet RJ-45 Connector .................................24
3.14 Audio Connector.................................................25
3.15 Compact Flash™ Socket (CN26).......................25
3.16 ACPI Connector..................................................27
3.17 Pin Assignments of Other Connectors.............27
3.17.1 CN25: Extra Power Connector Pin Assignment.................... 27
3.17.2 CN1: IrDA Connector Pin Assignment................................. 28
3.17.3 CN20: Standalone Power Connector Pin Assignment ........ 28
3.17.4 CN4: Flat Panel Bezel Connector.......................................... 28
C h a p t e r 4............................................................................30
4.1 Entering Setup....................................................30
4.2 Control Keys .......................................................31
4.3 Getting Help ........................................................32
4.4 The Main Menu....................................................33
4.5 Standard CMOS Setup Menu.............................34
4.6 Advanced BIOS Features...................................37
4.7 Advanced Chipset Features ..............................42
4.8 Integrated Peripherals........................................44
4.9 Power Management Setup.................................49
4.10 PnP/PCI Configuration Setup ............................54
4.11 PC Health Status.................................................56
4.12 Frequency/Voltage Control................................57
4.13 Load Fail-Safe Defaults......................................58
4.14 Load Optimized Defaults....................................59
4.15 Set Supervisor/User Password .........................60
4.16 Save & Exit Setup...............................................61
4.17 Exit Without Saving............................................62
A p p e n d i x A ......................................................................63
Watchdog Features ............................................................63

vi
Watchdog Overview ...........................................................64
Watchdog Control Sample.................................................66
Using the Watchdog Function...............................................66
Reload Timer...........................................................................66
Disable Timer ..........................................................................67
Enable Timer...........................................................................67
A p p e n d i x B ......................................................................69
On-Chip Serial ATA configuration.........................................70
Serial ATA Port Mode .............................................................70
Parallel ATA and Serial ATA Device Setup ......................71

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Introduction 1
C h a p t e r 1
Introduction
The SBC82810 is an Intel®Pentium®M/Celeron®M CPU
equipped Half-Size CPU card with graphics, Fast/Gigabit
Ethernet and audio interface. Designed with the space-limited
applications in mind, the SBC82810 is practically the finest
embedded Pentium®M board that exists. SBC82810 Series
adapt an Intel®low power consumption Pentium®M
microprocessors. To simplify system integration, it packs
provisions such as super I/Os, CRT/LVDS LCD/DVI, dual
Ethernet, CompactFlash, all on a single board. Unique
embedded features such as 2 serial ports (1 x RS-232, 1 x RS-
232/422/485) and that allow adoption of an extensive array of
PC peripherals. The industrial-grade construction of SBC82810
series allows your system to endure the continuous operation
in hostile environments where stability and reliability are basic
requirements. System dependability of SBC82810 series are
enhanced by its built-in watchdog timer, a special industrial
feature not commonly seen on other motherboards.
Designed for the professional embedded developers, the
Pentium®M embedded board SBC82810 Series is virtually the
ultimate one-step solution for embedded system applications.

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Introduction
2
1.1 Specifications
zCPU: Intel®Pentium®M / Celeron®M
zSystem Chipset: Intel®852GM/6300ESB
zBus Clock: 400 MHz Front Side Bus
zBIOS:
Phoenix-Award BIOS, Y2K compliant
4Mbit Flash, DMI, Plug and Play
SmartView for multiple LCD type selection, display
mode option and application extension features
RPL/PXE Ethernet Boot ROM
“Load Optimized Default” to backup customized
Setting in the BIOS flash chip to prevent from CMOS
battery fail
zSystem Memory:
One 184-pin DIMM socket
DDR-266 non-ECC SDRAM supported
Maximum SDRAM of up to 1GB
zL2 Cache: integrated in CPU
zOnboard IDE:
3 channels up to 4 devices (1 parallel ATA-100 and 2
serial ATA-150)
PATA-100 as PIO Mode 0-4, DMA Mode 0-2 and Ultra
DMA/33/66/100
zOnboard Serial ATA:
Independent DMA operation on two ports.
Data transfer rate up to 150 Mbyte/s
Altemate Device IDE and RAID Class Code option for
support of Soft RAID.
zCompact Flash Socket:
IDE1 support Compact Flash type-II Socket jumper
selectable as Master or Slave and DMA mode
supported
Power is 5V (default) or 3.3V (Option).

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Introduction 3
zOnboard Multi I/O:
One floppy port supporting up to two devices (LS-120 &
ZIP Bootable)
One SPP/EPP/ECP parallel port; supports LS-120
Two 16550 UART-compatible serial ports
1 x RS-232
1 x RS-232/422/485 and selectable via jumper setting
and auto flow control supported
1 x IrDA for wireless communication
zUSB Interface: 4 USB ports with fuse protection and
complies with USB Spec. Rev. 2.0
zReal Time Clock: Integrated Intel®6300ESB
zWatchdog Timer:
Integrate Intel®6300ESB
1024 levels, 0~600 seconds with SMI and Reset feature
zHardware Monitoring:
Integrate Winbond W83627HF Super I/O.
Monitoring for CPU/System temperatures,
System Voltage and Chassis/CPU Fan speeds
zGraphics/Streaming:
Integrate Intel®852GM GMCH
Unified Memory Architecture shares system memory
up to 32MB
Single display mode maximum resolutions:
CRT: 2548 x 1536
LVDS LCD: 1600 x 1200
DVI: 1280 x 1024
DualView display mode:
CRT: 2548 x 1536
LVDS LCD: 1600 x 1200
DVI: 1280 x 1024
LCD backlight control supported

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Introduction
4
zEthernet:
Dual Realtek 8100C PCI Bus 10/100M Base-T
Wake On LAN (via ATX power supply)
Equipped with RJ-45 interface
Optional with Realtek RTL8110S for 10/100/1000Base-T
zAudio:
Realtek ALC202A AC’97 codec audio
Amplify for speaker-out with 2.5W for each channel
MIC-in, Line-in, Line-out/Speaker-out (jumper
selectable)
zExpansion Slots:
PCI golden finger for 4 masters with PICMG compliant
connected to PCI interface; master 1/2/3/4.
zPower Management: ACPI (Advanced Configuration
and Power Interface)
NOTE: Specifications are subject to change without notice.
1.2 Utilities Supported
Chipset Driver
Ethernet Driver
VGA Drivers
Audio Drivers

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Jumpers and Connectors 5
C h a p t e r 2
Jumpers and Connectors
2.1 Board Layout and Fixing Holes
111.00
40.56
119.71
7.62
184.99
104.27
74.09
69.81
148.36
35.20
96.32
83.31
108.70
36.32
168.86
127.86
48.31
89.31
113.59
180.88
118.24
74.24
21.46
121.92
108.20
37.38
84.58
65.25
10.82
6.22
0.00
0.00
31.38
Component Side

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Jumpers and Connectors
6
184.99
121.92
15.4463.70
49.53
61.37
44.33
97.41
0.71
1.00
Solder Side

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Jumpers and Connectors 7
2.2 Placement

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Jumpers and Connectors
8
2.3 Jumper Settings
The SBC82810 Series is configured to match the needs of
your application with the proper jumper settings. The table
below is a summary of all the jumpers and their corresponding
functions onboard the SBC82810 Series. The succeeding
tables show the correct jumper settings for the onboard
devices.
Jumper Default Setting Jumper Setting
JP1 Audio Line Out/Speaker Out: Line Out Short 1-3, 2-4
JP2 Watchdog Reset Setting Open
JP3 Reset CMOS Short 1-2
JP4 LVDS Voltage Setting Short 1-2
JP5 Compact Flash Power Setting: 5V Short 2-3
JP6 Serial Port2 RS-232/422/485 Setting Short 3-5
Short 4-6
JP7 Serial Port2 RS-232/422/485 Setting Short 3-5
Short 4-6
JP8 Serial Port2 RS-232/422/485 Setting Short 1-2

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Jumpers and Connectors 9
2.3.1 Audio Output Select Jumper: JP1
Options Settings
Line Out Short 1-3, 2-4 (default)
Speaker Out Short 3-5, 4-6
JP1
246
135
2.3.2 Watch dog Reset setting:JP2
Options Settings
Disable Open(Default)
Enable Short
JP2
12
2.3.3 Reset CMOS Jumper: JP3
Options Settings
Normal Short 1-2 (default)
Clear CMOS Short 2-3
JP3
123
2.3.4 LVDS Voltage Setting : JP4
VDDM Settings
5V Short 2-3
3.3V Short 1-2(default)
JP4
1
2
3
2.3.5 CompactFlash Power Setting: JP5
Options Settings
5V Short 2-3(Default)
3.3V Short 1-2
JP5
1
2
3

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Jumpers and Connectors
10
2.3.6 COM2 Mode Select for Type: JP6; JP7; JP8
COM2 JP6 JP7 JP8
RS-232 (default) 3-5, 4-6 3-5, 4-6 1-2
RS-422 1-3, 2-4 1-3, 2-4 3-4,7-8
RS-485 1-3, 2-4 1-3, 2-4 5-6, 7-8
JP6/JP7 JP8
246
135
246
135
8
7

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Jumpers and Connectors 11
2.4 Connectors
The connectors allow the CPU card to connect with other parts
of the system. Some problems encountered by your system
may be a result from loose or improper connections. Ensure
that all connectors are in place and firmly attached. The
following table lists the function of each connector on the
SBC82810 Series. Their corresponding pin assignments are
described in Chapter 3.
Connectors Label
IrDA Connector CN1
DDR Connector CN2
Audio Connector CN3
Front Panel Bezel Connector CN4
Parallel IDE Connector CN5
Parallel Port Connector CN6
LAN2 RJ-45 Connector CN7
FDD Connector CN8
Serial ATA Channel2 Connector CN9
LAN1 RJ-45 Connector CN10
Serial ATA Channel1 Connector CN11
ACPI Power Connector CN12
LVDS Channel A Connector CN13
LVDS Channel B Connector CN14
Serial Port1 Connector CN15
LVDS Voltage Connecto CN16
DVI Connector CN17
Serial Port2 Connector CN18
USB Port0 & Port1 Connector CN19
Power Connector CN20
USB Port2 & Port3 Connector CN21
6-Pin Mini Dim Keyboard/Mouse Connector CN22
5-Pin Mouse Connector CN23
5-Pin Keyboard Connector CN24
+12V Power Connector CN25
Compact Flash Connector CN26

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Jumpers and Connectors
12
This page does not contain any information.

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Hardware Description 13
C h a p t e r 3
Hardware Description
3.1 Microprocessors
The SBC82810 Series supports Intel®Celeron®M and
Pentium®M CPUs. Systems based on these CPUs can be
operated under Windows 2000/XP and Linux environments.
The system performance depends on the microprocessor
installed onboard. Make sure all settings are correct for the
installed microprocessor to prevent any damage to the CPU.
3.2 BIOS
System BIOS used on the SBC82810 Series is Phoenix-Award
Plug and Play BIOS. The SBC82810 Series contains a single
4Mbit Flash.
3.3 System Memory
The SBC82810 Series industrial CPU card supports one 184-
pin DDR DIMM socket for a maximum memory of 1GB DDR
SDRAMs. The memory module can come in sizes of 64MB,
128MB, 256MB, 512MB and 1GB.

SBC82810 Pentium® M All-in-One Half-Size Board User’s Manual
Hardware Description
14
3.4 I/O Port Address Map
The Intel®Pentium®M/Celeron®M CPU communicates via I/O
ports. It has a total of 1KB port addresses available for
assignment to other devices via I/O expansion cards.
Address Devices
000-01F DMA controller #1
020-03F Interrupt controller #1
040-05F Timer
060-06F Keyboard controller
070-07F Real time clock, NMI
080-09F DMA page register
0A0-0BF Interrupt controller #2
0C0-0DF DMA controller #2
0F0 Clear math coprocessor busy signal
0F1 Reset math coprocessor
0F8-0FF Math processor
120/121 Enable watchdog timer operation (read)
1F0-1F8 Fixed disk controller
250-25F Winbond I/O #2
300-31F Prototype card
380-38F SDLC #2
3A0-3AF SDLC #1
3B0-3BF MDA video card (including LPT1)
3C0-3CF EGA card
3D0-3DF CGA card
3F0-3F7 Floppy disk controller
3F8-3FF Serial port #1 (COM1)
3E8-3EF Serial port #3 (COM3)
2F8-2FF Serial port #2 (COM2)
2E8-2EF Serial port #4 (COM4)
3F0-3FF Winbond I/O #1