AXIOMTEK SHB102 Series User manual

SHB102 Series
Intel®Core™2 Quad/Core™2 Duo
Celeron®Processor PICMG 1.3 Full-Size
Single Board Computer
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party‟s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is
recommended by the manufacturer that you follow the manufacturer‟s
instructions to only replace the same or equivalent type of battery, and
dispose of used ones.
Copyright 2008 AXIOMTEK Co., Ltd.
All Rights Reserved
November 2008, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity.
To prevent chipsets from electrostatic discharge damage, please take
care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
Before holding the board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. It
discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI are trademarks of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel®CoreTM 2 Quad/ CoreTM 2 Duo/Celeron®are trademarks of
Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered
brands of their respective owners.

iv
Table of Contents
Disclaimers.........................................................................................................ii
ESD Precautions...............................................................................................iii
CHAPTER 1 INTRODUCTION...................................................................................1
1.1 Specifications........................................................................................2
1.2 Utilities Supported.................................................................................4
1.3 I/O Bracket............................................................................................4
CHAPTER 2 JUMPERS AND CONNECTORS.......................................................... 5
2.1 Board Dimensions.................................................................................5
2.2 Board Layout.........................................................................................6
2.3 Jumper Settings ....................................................................................7
2.3.1 COM2 Mode Select Jumpers for RS-232/422/485 (JP7, JP6, JP5) 7
2.3.2 CMOS Clear Jumper (JP13)...........................................................8
2.3.3 ATX Auto Power On/Off (JP1)........................................................8
2.3.4 ME Clear Jumper (JP14)................................................................9
2.3.5 ME Disable/Enable Jumper (JP9)...................................................9
2.3.6 TPM Disable/Enable Jumper (JP10)............................................. 10
2.3.7 Audio Amplifier Jumper (JP11).....................................................10
2.4 Connectors..........................................................................................11
2.4.1 ATX 4 Pin 12V In Connector (CN4).............................................. 12
2.4.2 Front Panel Connector (CN2)....................................................... 12
2.4.3 LAN1 LED Connectors (CN20).....................................................13
2.4.4 LAN2 LED Connectors (CN8)....................................................... 13
2.4.5 COM Port RS-232 Pin Assignment (CN5, CN9) ...........................14
2.4.6 COM2 RS-422/485 Pin Assignment .............................................14
2.4.7 CPU Fan Connector (CN32).........................................................15
2.4.8 System Fan Connectors (CN33, CN34)........................................ 15
2.4.9 Floppy Disk Port Connector (CN1) ...............................................15
2.4.10 Intel®HD Audio Digital Header (CN24).........................................16
2.4.11 PS/2 Keyboard, Mouse Connectors (CN29, CN30).......................17
2.4.12 Ethernet RJ-45 Connectors (CN11, CN16)................................... 17
2.4.13 Parallel Port Connector (CN6)...................................................... 18
2.4.14 SATA Connectors (CN13, CN14, CN15, CN17, CN18, CN19)......19
2.4.15 USB Connectors (CN21, CN23, CN25) ........................................19
2.4.16 USB Port Connectors (CN27, CN31)............................................ 20
2.4.17 DB15 CRT Connector (CN22) ......................................................20
CHAPTER 3 HARDWARE INSTALLATION ............................................................ 21
3.1 Installing the Processor.......................................................................21
3.2 Installing the Memory ..........................................................................26
CHAPTER 4 HARDWARE DESCRIPTION.............................................................. 27
4.1 Microprocessors..................................................................................27
4.2 BIOS ...................................................................................................27
4.3 System Memory...................................................................................27
4.4 I/O Port Address Map..........................................................................28

v
4.5 Interrupt Controller (IRQ) Map.............................................................29
CHAPTER 5 AMI BIOS UTILITY ............................................................................31
5.1 Starting................................................................................................31
5.2 Navigation Keys ..................................................................................31
5.3 Main Menu ..........................................................................................33
5.4 Advanced Menu ..................................................................................34
5.5 PCI PnP Menu.....................................................................................49
5.6 Boot Menu........................................................................................... 51
5.7 Security Menu .....................................................................................55
5.8 Chipset Menu...................................................................................... 56
5.9 Exit Menu............................................................................................61
CHPATER 6 INSTALLATION OF DRIVERS ...........................................................63
6.1 Installing Chipset Driver.......................................................................63
6.2 Installing VGA Driver...........................................................................67
6.3 Installing LAN Driver............................................................................70
6.4 Installing AUDIO Driver .......................................................................74
6.5 Installing iAMT (Active Management Technology) Driver .................... 76
6.5.1 LMS_SOL Setup .......................................................................... 76
6.5.2 LMS_SOL_IS Setup.....................................................................80
6.6 Installing MEI (Management Engine Interface) Driver.......................... 84
APPENDIX A WATCHDOG TIMER.........................................................................89
APPENDIX B PCI IRQ ROUTING............................................................................ 91
APPENDIX C CONFIGURING SATA FOR RAID FUNCTION ................................. 93
APPENDIX D iAMT SETTINGS............................................................................. 107
D.1 Entering MEBx .................................................................................. 107
D.2 Set & Change Password ...................................................................108
D.3 Intel®iAMT Settings.......................................................................... 110
D.4 iAMT Web Console........................................................................... 115
APPENDIX E PICMG v1.3 INTERFACE DEFINITION........................................... 119

vi
MEMO

SHB102 LGA775 Full-Size SBC User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
The SHB102 PICMG 1.3 full-size Single Board Computer supports
LGA775 socket for Intel®Core™2 Quad / Core™2 Duo/Celeron®
processors with 45/65nm technology and FSB 800/1066/1333 MHz.
The board integrates Intel®Q45 andICH10DO chipset that delivers
outstanding system performance through high-bandwidth interfaces,
multiple I/O functions for interactive applications and various
embedded computing solutions. There are four 240-pin DDR3 DIMM
sockets for dual channel DDR3 800/1066, maximum memory capacity
up to 16GB. The board also features dual Gigabit Ethernet, six serial
ATA ports at maximum transfer rate up to 3Gbs, and SATA RAID
0/1/5/10 byICH10DO. Ten USB 2.0 high speed compliant ports and
built-in Intel®HD Audio Digital Header can achieve the best stability
and reliability for industrial applications.

SHB102 LGA775 Full-Size SBC User’s Manual
Introduction
2
1.1 Specifications
CPU
Intel®Core™2 Quad / Core™2 Duo/Celeron®
processors
System Chipset
Intel®Q45 and ICH10DO
CPU Socket
LGA775 Socket
Front-Side Bus
800/1066/1333 MHz
BIOS
AMI BIOS via SPI interface with socket
System Memory
Four 240-pin DDR3 DIMM sockets
Maximum up to 16GB DDR3 memory
Supports DDR3 800/1066 memory
L2 Cache: integrated in CPU
Onboard Multi-I/O
Parallel Port: one 26-pin 2.54 pitch box-header,
SPP/EPP/ECP supported
Serial Port: one for RS-232 (COM1) and one port for
RS-232/422/485 (COM2)
Floppy controller: supports two drives (1.44MB for each)
USB Interface
Ten USB ports compliant with USB Spec. Rev. 2.0 (eight
ports on SHB102, four ports to SHB connector-C golden
fingers)
VGA Controller
Chipset -- Intel®integrated Graphics Gen5 on Intel®Q45
supports 3D, 2D, video capabilities
Memory Size -- Intel®DVMT supported; preallocated

SHB102 LGA775 Full-Size SBC User’s Manual
Introduction
3
memory for frame buffer option as 32/48/64/128/256MB,
and 96 MB (0 + 96), 160 MB (64 + 96), 224 MB (128 + 96),
352 MB (256 + 96).
Resolution -- Analog output -- the analog port utilizes an
integrated 350MHz 24-bit RAMDAC that can directly drive a
standard progressive scan analog monitor up to a resolution
of 2048x1536 pixels with 32-bit color at 75 Hz
Analog Output Interface -- CRT from DAC output via 15-pin
D-Sub connector on the edge; CRT always ON supported
Ethernet
The LAN1/LAN2 is 82574L Ethernet controller support
10/100/1000 Mb/s
Dual PCI-Express x1 LAN
Serial ATA
Support Serial ATA/Serial ATA II
Six Serial ATA-II ports, 3GB/s performance and SATA RAID
0/1/5/10 by ICH10DO
Audio
16-pin 2.54 pin-header (Intel®HD Audio Digital Header)
Hardware Monitoring
Monitoring temperatures, voltages, and cooling fan status
Watchdog Timer
Reset Supported (1-255 level)
Dimensions
338mm x 126mm
NOTE All specifications and images are subject to change without
notice.

SHB102 LGA775 Full-Size SBC User’s Manual
Introduction
4
1.2 Utilities Supported
Intel®Q45 Utility and Drivers
VGA Drivers
Ethernet Utility and Drivers
RAID Utility
iAMT Utility and Drivers
ITPM Utility
1.3 I/O Bracket

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
5
CHAPTER 2
JUMPERS AND CONNECTORS
2.1 Board Dimensions

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
6
2.2 Board Layout
BIOS
CN21 CN23 CN25
CN20
CN8
CN27 CN31
CN14 CN18
CN15 CN19
CN17 CN13
CN5 CN9
CN6
CN1
CN29
CN30
JP10
JP9
JP1
BAT1
CN33
CN34
JP12 JP13
CN4
CN32
JP11
JP5 JP6 JP7
CN24
CN2
CN16 CN11
CN10 CN12
MCH ICH
CN22
CN3 CN7
JP14

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
7
2.3 Jumper Settings
Proper jumper settings configure the SHB102 to meet your application
purpose.
2.3.1 COM2 Mode Select Jumpers for RS-232/422/485
(JP7, JP6, JP5)
These jumpers select the COM2 port‟s communication mode to operate
RS-232 or RS-422/485.
Description
Function
Jumper Setting
COM2
RS-232
(Default)
JP7
JP6
JP5
RS-422
JP7
JP6
JP5
RS-485
JP7
JP6
JP5

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
8
2.3.2 CMOS Clear Jumper (JP13)
You may need to use this jumper is to clear the CMOS memory if
incorrect BIOS settings.
Description
Function
Jumper Setting
CMOS Clear
Normal
(Default)
Clear
CMOS
2.3.3 ATX Auto Power On/Off (JP1)
When Jumper JP1 is set OPEN for AC power input, the system will be
automatically power ON without pressing soft power button; when JP1
is SHORT for AC power input, it is necessary to manually press soft
power button to make the system power ON.
Note This function is similar to the feature of Power On after
Power Failed, which is controlled by hardware circuitry
instead of BIOS.
Description
Function
Jumper Setting
ATX Auto
Power
On/Off
Disable
(Default)
Enable

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
9
2.3.4 ME Clear Jumper (JP14)
Description
Function
Jumper Setting
ME Clear
Normal
(Default)
Clear
CMOS
2.3.5 ME Disable/Enable Jumper (JP9)
Description
Function
Jumper Setting
ME Disable/
Enable
Enable
(Default)
Disable

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
10
2.3.6 TPM Disable/Enable Jumper (JP10)
Description
Function
Jumper Setting
TPM
Disable/
Enable
Enable
(Default)
Disable
2.3.7 Audio Amplifier Jumper (JP11)
Description
Function
Jumper Setting
Audio
Amplifier
Disable
Enable
(Default)

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
11
2.4 Connectors
Connectors connect this board with other parts of the system. Loose or
improper connection might cause problems. Make sure all connectors
are properly and firmly connected.
Here is a summary table shows you all connectors on the board.
Connector
Label
Connector
Label
FDD
CN1
SATA1
CN17
Front Panel Connector
CN2
SATA3
CN18
DDRIII CH2 DIMM1
CN3
SATA2
CN19
CPU ATX 12V IN
CN4
LAN1 Ext. LED
CN20
COM1
CN5
USB3,4
CN21
Parallel Port
CN6
VGA
CN22
DDRIII CH2 DIMM0
CN7
USB5,6
CN23
LAN2 Ext. LED
CN8
Audio Connector
CN24
COM2
CN9
USB11,12
CN25
DDRIII CH1 DIMM1
CN10
Back Panel USB1
CN27
LAN2_RJ45
CN11
Keyboard
CN29
DDRIII CH1 DIMM0
CN12
Mouse
CN30
SATA6
CN13
Back Panel USB2
CN31
SATA4
CN14
CPU FAN
CN32
SATA5
CN15
AUX FAN
CN33
LAN1_RJ45
CN16
SYS FAN
CN34

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
12
2.4.1 ATX 4 Pin 12V In Connector (CN4)
You can connect it to the ATX12V power supply for CPU Core Voltage.
Pin
Signal
1
GND
2
GND
3
+12V
4
+12V
2.4.2 Front Panel Connector (CN2)
Power LED
This 3-pin connector denoted as Pin 1 and Pin 5 connects the
system power LED indicator to such a switch on the case. Pin 1 is
assigned as +, and Pin 5 as -. The Power LED lights up when the
system is powered ON. Pin 3 is defined as GND.
External Speaker and Internal Buzzer Connector
Pin 2, 4, 6 and 8 can be connected to the case-mounted speaker
unit or internal buzzer. While connecting the CPU card to an
internal buzzer, please short pins 2-4; while connecting to an
external speaker, you need to set pins 2-4 to Open and connect the
speaker cable to pin 8 (+) and pin 2 (-).
ATX Power On/Off Button
This 2-pin connector denoted as Pin 9 and 10 connects the front
panel‟s ATX power button to the CPU card, which allows users to
control ATX power supply to be power on/off.
System Reset Switch
Pin 11 and 12 can be connected to the case-mounted reset switch

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
13
that reboots your computer instead of turning OFF the power switch.
It is a better way to reboot your system for a longer life of the
system‟s power supply.
HDD Activity LED
This connection is linked to hard drive activity LED on the control
panel. LED flashes when HDD is being accessed. Pin 13 and 14
connect the hard disk drive to the front panel HDD LED, Pin 13
assigned as -, and Pin 14 as +.
2.4.3 LAN1 LED Connectors (CN20)
Pin
Signal
1
LED (+)
2
LED (-)
3
100, Low Active
4
+ 3.3V
5
1000, Low Active
2.4.4 LAN2 LED Connectors (CN8)
Pin
Signal
1
LED (+)
2
LED (-)
3
100, Low Active
4
+ 3.3V
5
1000, Low Active

SHB102 LGA775 Full-Size SBC User’s Manual
Jumpers and Connectors
14
2.4.5 COM Port RS-232 Pin Assignment (CN5, CN9)
The serial interface for the board consists of CN5 port (COM1) support
for RS-232, and CN9 (COM2) for RS-232/RS422/RS485.
Pin
Signal
Pin
Signal
2
4
6
1
3
5
78
910
1
Data Carrier Detect
(DCD)
2
Data Set Ready (DSR)
3
Receive Data (RXD)
4
Request to Send (RTS)
5
Transmit Data (TXD)
6
Clear to Send (CTS)
7
Data Terminal Ready
(DTR)
8
Ring Indicator (RI)
9
Ground (GND)
10
Ground (GND)
2.4.6 COM2 RS-422/485 Pin Assignment
COM2 Serial Port 10-pin (Box-header) Connector Pin Assignment list
Pin #
Signal Name
RS-422
RS-485
1
TX-
DATA-
2
No connector
No connector
3
TX+
DATA+
4
No connector
No connector
5
RX+
No connector
6
No connector
No connector
7
RX-
No connector
8
No connector
No connector
9
GND
GND
10
GND
GND