AXIOMTEK SHB102 Series User manual

SHB102
Intel®Core™2 Quad/Core™2 Duo
Celeron®Processor PICMG 1.3
Full-Size Single Board Computer
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2017 Axiomtek Co., Ltd.
All Rights Reserved
Feb. 2017, Version A5
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please take care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. It discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®CoreTM i7 / CoreTM i5 / CoreTM i3 are trademarks of Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Realtek is a trademark of Realtek Semi-Conductor Co., Ltd.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 Specifications......................................................................................1
1.2 Utilities Supported ..............................................................................3
1.3 I/O Bracket...........................................................................................3
Chapter 2 Board and Pin Assignments.................... 5
2.1 Board Dimensions ..............................................................................5
2.2 Board Layout.......................................................................................6
2.3 Jumper Settings..................................................................................7
2.3.1 COM2 Mode Select Jumpers (JP5, JP6, JP7)............................................ 7
2.3.2 CMOS Clear Jumper (JP13) ....................................................................... 7
2.3.3 ATX Auto Power On/Off (JP1)..................................................................... 8
2.3.4 ME Clear Jumper (JP14)............................................................................. 8
2.3.5 ME Disable/Enable Jumper (JP6)............................................................... 8
2.3.6 TPM Disable/Enable Jumper (JP10)........................................................... 9
2.3.7 Audio Amplifier Jumper (JP11).................................................................... 9
2.4 Connectors ........................................................................................10
2.4.1 ATX 4 Pin 12V In Connector (CN4)............................................................11
2.4.2 Front Panel Connector (CN2) ....................................................................11
2.4.3 LAN1 LED Connector (CN20)................................................................... 12
2.4.4 LAN2 LED Connector (CN8)..................................................................... 12
2.4.5 COM Port RS-232 Pin Assignment (CN5, CN9)....................................... 12
2.4.6 COM2 RS-422/485 Pin Assignment.......................................................... 13
2.4.7 CPU Fan Connector (CN32) ..................................................................... 13
2.4.8 System Fan Connectors (CN33, CN34).................................................... 13
2.4.9 Floppy Disk Port Connector (CN1)............................................................ 14
2.4.10 Intel® HD Audio Digital Header (CN24).................................................... 14
2.4.11 PS/2 Keyboard, Mouse Connector (CN29, CN30).................................... 14
2.4.12 Ethernet RJ-45 Connectors (CN11, CN16)............................................... 15
2.4.13 Parallel Port Connector (CN6) .................................................................. 16
2.4.14 SATA Connectors (CN13, CN14, CN15, CN17, CN18, CN19) ................. 16
2.4.15 USB Connectors (CN21, CN23, CN25) .................................................... 17
2.4.16 USB Port Connector (CN27, CN31).......................................................... 17
2.4.17 DB15 CRT Connector (CN22)................................................................... 18
Chapter 3 Hardware Installation ........................... 19

v
3.1 Installing the Processor....................................................................20
3.2 Installing the Memory .......................................................................23
Chapter 4 Hardware Description ........................... 25
4.1 Microprocessors ...............................................................................25
4.2 BIOS ...................................................................................................25
4.3 System Memory.................................................................................25
4.4 I/O Port Address Map........................................................................26
4.5 Interrupt Controller (IRQ) Map .........................................................27
Chapter 5 PHOENIX-AWARD BIOS Utility .............. 29
5.1 Entering Setup...................................................................................29
5.2 Control Keys......................................................................................30
5.3 Getting Help.......................................................................................31
5.4 Main Menu..........................................................................................31
5.5 Advanced Menu.................................................................................32
5.6 PCI PnP Menu....................................................................................46
5.7 Boot Menu..........................................................................................48
5.8 Security Menu....................................................................................52
5.9 Chipset Menu.....................................................................................53
5.10 Exit Menu...........................................................................................57
Chapter 6 Installation of Drivers ........................... 59
6.1 Installing Chipset Driver...................................................................59
6.2 Installing VGA Driver.........................................................................61
6.3 Installing VGA Driver.........................................................................64
6.4 Installing LAN Driver.........................................................................67
6.5 Installing Audio Driver......................................................................70
6.6 Installing iAMT (Active Management Technology) Driver..............72
6.6.1 LMS_SOL Setup ....................................................................................... 72
6.6.2 LMS_SOL_IS Setup.................................................................................. 74
6.7 Installing MEI (Management Engine Interface) Driver....................77
Appendix A Watchdog Timer .................................... 81
Watchdog Timer Setting..............................................................................81
Using the Watchdog Function ....................................................................81
Appendix B PCI IRQ Routing..................................... 83

vi
Appendix C Configuring SATA for RAID Function..... 85
Configuring SATA Hard Drive(s) for RAID Function (Controller:
Intel®ICH10DO/DO DH only)........................................................................85
Appendix D iAMT Settings........................................ 95
D.1 Entering MEBx...................................................................................95
D.2 Set & Change Password...................................................................96
D.3 Intel®iAMT Settings..........................................................................97
D.4 iAMT Web Console..........................................................................102
Appendix E PICMG V1.3 Interface Definition......... 105

SHB102 LGA775 SBC User’s Manual
Introduction 1
Chapter 1
Introduction
The SHB102 PICMG 1.3 full-size Single Board Computer supports LGA775 socket for Intel®
Core™2 Quad / Core™2 Duo/Celeron®processors with 45/65nm technology and FSB
800/1066/1333 MHz. The board integrates Intel®Q45 andICH10DO chipset that delivers
outstanding system performance through high-bandwidth interfaces, multiple I/O functions for
interactive applications and various embedded computing solutions. There are four 240-pin
DDR3 DIMM sockets for dual channel DDR3 800/1066, maximum memory capacity up to 8GB.
The board also features dual Gigabit Ethernet, six serial ATAports at maximum transfer rate up
to 3Gbs, and SATA RAID 0/1/5/10 byICH10DO. Ten USB 2.0 high speed compliant ports and
built-in Intel®HD Audio Digital Header can achieve the best stability and reliability for industrial
applications.
1.1 Specifications
CPU
Intel®Core™2 Quad / Core™2 Duo/Celeron®processors
System Chipset
Intel®Q45 and ICH10DO
CPU Socket
LGA775 Socket
Front-Side Bus
800/1066/1333 MHz
BIOS
Phoenix-Award BIOS via SPI interface with socket

SHB102 LGA775 SBC User’s Manual
2 Introduction
System Memory
Four 240-pin DDR3 DIMM sockets
Maximum up to 8GB DDR3 memory
Support DDR3 800/1066 memory
L2 Cache
Integrated in CPU
Onboard Multi-I/O
Parallel Port: one 26-pin 2.54 pitch box-header, SPP/EPP/ECP supported
Serial Port: one for RS-232 (COM1) and one port for RS-232/422/485 (COM2)
Floppy controller: supports two drives (1.44MB for each)
USB Interface
Ten USB ports compliant with USB Spec. Rev. 2.0 (Six ports on SHB102, four ports
to SHB connector-C golden fingers)
VGA Controller
Chipset -- Intel®integrated Graphics Gen5 on Intel®Q45 supports 3D, 2D, video
capabilities
Memory Size -- Intel®DVMT supported; preallocated memory for frame buffer option
as 32/48/64/128/256MB, and 96 MB (0 + 96), 160 MB (64 + 96), 224 MB (128 + 96),
352 MB (256 + 96)
Resolution -- Analog output -- the analog port utilizes an integrated 350MHz 24-bit
RAMDAC that can directly drive a standard progressive scan analog monitor up to a
resolution of 2048x1536 pixels with 32-bit color at 75 Hz
Analog Output Interface -- CRT from DAC output via 15-pin D-Sub connector on the
edge; CRT always ON supported
Ethernet
The LAN1/LAN2 is 82574L Ethernet controller support 10/100/1000 Mb/s
Dual PCI-Express x1 LAN
Serial ATA
Support Serial ATA/Serial ATA II
Six Serial ATA-II ports, 3GB/s performance and SATA RAID 0/1/5/10 by ICH10DO
Audio
10-pin 2.0 pin-header (Intel®HD Audio Digital Header)
Hardware Monitoring
Monitoring temperatures, voltages, and cooling fan status
Watchdog Timer
Reset Supported (1-255 level)
Dimensions
338mm x 126mm
Note
All specifications and images are subject to change without notice.

SHB102 LGA775 SBC User’s Manual
Introduction 3
1.2 Utilities Supported
Intel®Q45 Utility and Drivers
VGA Drivers
Ethernet Utility and Drivers
RAID Utility
iAMT Utility and Drivers
ITPM Utility
1.3 I/O Bracket

SHB102 LGA775 SBC User’s Manual
4 Introduction
This page is intentionally left blank.

SHB102 LGA775 SBC User’s Manual
Board and Pin Assignments 5
Chapter 2
Board and Pin Assignments
2.1 Board Dimensions

SHB102 LGA775 SBC User’s Manual
6 Board and Pin Assignments
2.2 Board Layout
BIOS
CN21 CN23 CN25
CN20
CN8
CN27 CN31
CN14 CN18
CN15 CN19
CN17 CN13
CN5 CN9
CN6
CN1
CN29
CN30
JP10
JP9
JP1
BAT1
CN33
CN34
JP12 JP13
CN4
CN32
JP11
JP5 JP6 JP7
CN24
CN2
CN16 CN11
CN10 CN12
MCH ICH
CN22
CN3 CN7
JP14

SHB102 LGA775 SBC User’s Manual
Board and Pin Assignments 7
2.3 Jumper Settings
Proper jumper settings configure the SHB102 to meet your application purpose.
2.3.1 COM2 Mode Select Jumpers (JP5, JP6, JP7)
These jumpers select the COM2 port’s communication mode to operate RS-232 or
RS-422/485.
Description
Function
Jumper Setting
COM2
RS-232
(Default)
JP5
JP6
JP7
RS-422
JP5
JP6
JP7
RS-485
JP5
JP6
JP7
2.3.2 CMOS Clear Jumper (JP13)
You may need to use this jumper is to clear the CMOS memory if incorrect BIOS
settings.
Description
Function
Jumper Setting
CMOS Clear
Normal
(Default)
Clear CMOS

SHB102 LGA775 SBC User’s Manual
8 Board and Pin Assignments
2.3.3 ATX Auto Power On/Off (JP1)
When Jumper JP1 is set OPEN for AC power input, the system will be automatically
power ON without pressing soft power button; when JP1 is SHORT forAC power input, it
is necessary to manually press soft power button to make the system power ON.
Note
This function is similar to the feature of Power On after Power Failed,
which is controlled by hardware circuitry instead of BIOS.
Description
Function
Jumper Setting
ATX Auto Power
On/Off
Disable
(Default)
Enable
2.3.4 ME Clear Jumper (JP14)
Description
Function
Jumper Setting
ME Clear
Normal
(Default)
Clear CMOS
2.3.5 ME Disable/Enable Jumper (JP6)
Description
Function
Jumper Setting
ME Disable/
Enable
Enable
(Default)
Disable

SHB102 LGA775 SBC User’s Manual
Board and Pin Assignments 9
2.3.6 TPM Disable/Enable Jumper (JP10)
Description
Function
Jumper Setting
TPM Disable/
Enable
Enable
(Default)
Disable
2.3.7 Audio Amplifier Jumper (JP11)
Description
Function
Jumper Setting
Audio Amplifier
Disable
Enable
(Default)

SHB102 LGA775 SBC User’s Manual
10 Board and Pin Assignments
2.4 Connectors
Connectors connect this board with other parts of the system. Loose or improper connection
might cause problems. Make sure all connectors are properly and firmly connected.
Here is a summary table shows you all connectors on the board.
Connector
Label
Connector
Label
FDD
CN1
SATA1
CN17
Front Panel Connector
CN2
SATA3
CN18
DDRIII CH2 DIMM1
CN3
SATA2
CN19
CPU ATX 12V IN
CN4
LAN1 Ext. LED
CN20
COM1
CN5
USB3,4
CN21
Parallel Port
CN6
VGA
CN22
DDRIII CH2 DIMM0
CN7
USB5,6
CN23
LAN2 Ext. LED
CN8
Audio Connector
CN24
COM2
CN9
USB11,12
CN25
DDRIII CH1 DIMM1
CN10
Back Panel USB1
CN27
LAN2_RJ45
CN11
Keyboard
CN29
DDRIII CH1 DIMM0
CN12
Mouse
CN30
SATA6
CN13
Back Panel USB2
CN31
SATA4
CN14
CPU FAN
CN32
SATA5
CN15
AUX FAN
CN33
LAN1_RJ45
CN16
SYS FAN
CN34

SHB102 LGA775 SBC User’s Manual
Board and Pin Assignments 11
2.4.1 ATX 4 Pin 12V In Connector (CN4)
You can connect it to the ATX12V power supply for CPU Core Voltage.
Pin
Signal
1
GND
2
GND
3
+12V
4
+12V
2.4.2 Front Panel Connector (CN2)
Power LED
This 3-pin connector denoted as Pin 1 and Pin 5 connects the system power LED
indicator to such a switch on the case. Pin 1 is assigned as +, and Pin 5 as -. The Power
LED lights up when the system is powered ON. Pin 3 is defined as GND.
External Speaker and Internal Buzzer Connector
Pin 2, 4, 6 and 8 can be connected to the case-mounted speaker unit or internal buzzer.
While connecting the CPU card to an internal buzzer, please short pins 2-4; while
connecting to an external speaker, you need to set pins 2-4 to Open and connect the
speaker cable to pin 8 (+) and pin 2 (-).
ATX Power On/Off Button
This 2-pin connector denoted as Pin 9 and 10 connects the front panel’s ATX power
button to the CPU card, which allows users to control ATX power supply to be power
on/off.
System Reset Switch
Pin 11 and 12 can be connected to the case-mounted reset switch that reboots your
computer instead of turning OFF the power switch. It is a better way to reboot your
system for a longer life of the system’s power supply.
HDD Activity LED
This connection is linked to hard drive activity LED on the control panel. LED flashes
when HDD is being accessed. Pin 13 and 14 connect the hard disk drive to the front
panel HDD LED, Pin 13 assigned as -, and Pin 14 as +.

SHB102 LGA775 SBC User’s Manual
12 Board and Pin Assignments
2.4.3 LAN1 LED Connector (CN20)
Pin
Signal
1
LED (+)
2
LED (-)
3
100, Low Active
4
+ 3.3V
5
1000, Low Active
2.4.4 LAN2 LED Connector (CN8)
Pin
Signal
1
LED (+)
2
LED (-)
3
100, Low Active
4
+ 3.3V
5
1000, Low Active
2.4.5 COM Port RS-232 Pin Assignment (CN5, CN9)
The serial interface for the board consists of CN5 port (COM1) support for RS-232, and
CN9 (COM2) for RS-232/RS422/RS485.
Pin
Signal
Pin
Signal
2
4
6
1
3
5
78
910
1
Data Carrier Detect
(DCD)
2
Data Set Ready (DSR)
3
Receive Data (RXD)
4
Request to Send (RTS)
5
Transmit Data (TXD)
6
Clear to Send (CTS)
7
Data Terminal Ready
(DTR)
8
Ring Indicator (RI)
9
Ground (GND)
10
Ground (GND)

SHB102 LGA775 SBC User’s Manual
Board and Pin Assignments 13
2.4.6 COM2 RS-422/485 Pin Assignment
COM2 Serial Port 10-pin (Box-header) Connector Pin Assignment list
Pin
Signal
RS-422
RS-485
1
TX-
DATA-
2
No connector
No connector
3
TX+
DATA+
4
No connector
No connector
5
RX+
No connector
6
No connector
No connector
7
RX-
No connector
8
No connector
No connector
9
GND
GND
10
GND
GND
2.4.7 CPU Fan Connector (CN32)
A CPU fan is always needed for cooling CPU heat. The CPU fan connector CN32
provides power to the CPU fan.
Pin
Signal
1
Ground
2
+12V
3
Rotation Detection
4
Speed Control
2.4.8 System Fan Connectors (CN33, CN34)
You can connect the system cooling fan cable to CN33/CN34 for system cooling fan
power.
Pin
Signal
1
GND
2
+12V
3
Rotation Detection

SHB102 LGA775 SBC User’s Manual
14 Board and Pin Assignments
2.4.9 Floppy Disk Port Connector (CN1)
The board provides a 34-pin header type connector, CN1, supporting up to two floppy
drives. The floppy drives may be any one of the following types: 5.25" 360KB/1.2MB and
3.5" 720KB/1.44MB/2.88MB.
Pin
Signal
Pin
Signal
Pin
Signal
1
GND
2
Drive Density Select
3
GND
4
No connector
5
GND
6
No connector
7
GND
8
Index#
9
GND
10
Motor enable A#
11
GND
12
No connector
13
GND
14
Drive select A#
15
GND
16
No connector
17
GND
18
Direction#
19
GND
20
STEP#
21
GND
22
Write data#
23
GND
24
Write gate#
25
GND
26
Track 0 #
27
GND
28
Write protect#
29
No connector
30
Read data#
31
GND
32
Head selection#
33
No connector
34
Disk change#
2.4.10 Intel® HD Audio Digital Header (CN24)
Pin
Signal
Pin
Signal
2
4
6
1
3
5
78
910
1
MIC-IN
2
GND
3
Line In L
4
GND
5
Line In R
6
GND
7
Audio Out L
8
GND
9
Audio Out R
10
GND
2.4.11 PS/2 Keyboard, Mouse Connector (CN29, CN30)
The board provides the Keyboard (CN29)/ Mouse (CN30) interface with a 5-pin
connector.
Pin
Signal
1
Clock
2
DATA
3
No connector
4
GND
5
VCC