AXIOMTEK MANO111 Series User manual

MANO111 Series
AMD Embedded R-Series APU
Mini ITX SBC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2014 Axiomtek Co., Ltd.
All Rights Reserved
January 2014, Version A3
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please take care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. It discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
AMD is trademark of AMD Corporation, Inc.
Winbond is a trademark of Winbond Electronics Corp.
Realtek is a trademark of Realtek Semi-Conductor Co., Ltd.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 Features...............................................................................................1
1.2 Specifications......................................................................................2
1.3 Utilities Supported ..............................................................................3
Chapter 2 Board and Pin Assignments.................... 5
2.1 Board Dimensions and Fixing Holes.................................................5
2.2 Board Layout.......................................................................................8
2.3 Jumper Settings................................................................................10
2.3.1 COM4 Data/Power Selection (JP2)........................................................... 12
2.3.2 COM3 Data/Power Selection (JP3)........................................................... 12
2.3.3 COM2 Data/Power Selection (JP4)........................................................... 12
2.3.4COM1 Data/Power Selection (JP5)........................................................... 12
2.3.5 TPM Normal Operation/Special Commands Selection (JP6) ................... 13
2.3.6 Auto Power On (JP7) ................................................................................ 13
2.3.7 Restore BIOS Optimal Defaults (JP10)..................................................... 13
2.3.8 LVDS Brightness Control Mode Setting (JP11)......................................... 13
2.3.9 LVDS Voltage Selection (JP12 and JP13) ................................................ 14
2.3.10 COM1 RS-232/422/485 Mode Setting (JP14, JP15, JP16)...................... 14
2.3.11 DASH Setting (JP17) ................................................................................ 14
2.4 Connectors ........................................................................................15
2.4.1 COM Connectors (CN1, CN2, CN3 and CN5).......................................... 16
2.4.2 Power Connector (CN4)............................................................................ 17
2.4.3 PCI-Express Mini Card Connector (CN6) ................................................. 17
2.4.4 SIM Card Slot (CN7) ................................................................................. 18
2.4.5 Inverter Connector (CN8).......................................................................... 18
2.4.6 USB Connectors (CN9 and CN10)............................................................ 19
2.4.7 LVDS Connector (CN11) ........................................................................... 20
2.4.8 LAN and USB Connector (CN12).............................................................. 22
2.4.9 Dual DVI-D Connector (CN13).................................................................. 23
2.4.10 USB and DisplayPort Connectors (CN14~15 and CN18~19)................... 24
2.4.11 High Rise D-Sub and LAN Connectors (CN16 and CN20)....................... 26
2.4.12 Six Terminal Earphone Jack (CN17)......................................................... 26
2.4.13 FAN Connectors (FAN1, FAN2 and FAN3) ............................................... 27
2.4.14 Digital I/O Connector (JP1) ....................................................................... 27
2.4.15 Front Panel Connector (JP8) .................................................................... 28
2.4.16 Serial ATA Connectors (SATA1, SATA2, SATA3 and SATA4) ................... 29

v
2.4.17 CFast™ Socket (SCN1) ............................................................................ 29
Chapter 3 Hardware Installation ........................... 31
3.1 Installing the Processor....................................................................31
3.2 Installing the Memory .......................................................................34
Chapter 4 Hardware Description ........................... 35
4.1 APU (Accelerated Processing Unit).................................................35
4.2 BIOS ...................................................................................................35
4.3 System Memory.................................................................................35
4.4 I/O Port Address Map........................................................................36
4.5 Interrupt Controller (IRQ) Map .........................................................38
4.6 Memory Map ......................................................................................39
Chapter 5 AMI BIOS Setup Utility .......................... 41
5.1 Starting...............................................................................................41
5.2 Navigation Keys ................................................................................41
5.3 Main Menu..........................................................................................42
5.4 Advanced Menu.................................................................................43
5.5 Chipset Menu.....................................................................................51
5.6 Boot Menu..........................................................................................54
5.7 Security Menu....................................................................................55
5.8 Save & Exit Menu ..............................................................................56
Chapter 6 Dash User Guide.................................... 59
Appendix A Watchdog Timer................................... 71
About Watchdog Timer................................................................................71
How to Use Watchdog Timer.......................................................................71
Sample Program ..........................................................................................72
Appendix B Digital I/O ............................................. 73
About Digital I/O...........................................................................................73
Digital I/O Programming..............................................................................73

vi
This page is intentionally left blank.

MANO111 AMD Embedded R-Series APU Mini ITX SBC
Introduction 1
Chapter 1
Introduction
The MANO111 Series supports AMD R-Series APU. The board integrates the Fusion
Controller Hub A75 and delivers outstanding system performance through high-bandwidth
interfaces, multiple I/O functions for interactive applications and various embedded computing
solutions.
There are two 204-pin unbuffered SO-DIMM sockets for dual channel DDR3 with frequency up
to 1600MT/s, maximum memory capacity up to 16GB. It also features two Gigabit/Fast
Ethernet ports, four serial ATA channels at maximum transfer rate up to 6Gb/s, four USB 3.0
and ten USB 2.0 high speed compliant, and built-in HD audio codec that can achieve the best
stability and reliability for industrial applications. Additionally, it provides you with unique
embedded features, such as 5 serial ports and Mini ITX form factor that supports an extensive
array of PC peripherals.
1.1 Features
FS1r2 socket AMD Embedded R-Series APU
AMD A75 PCH
Integrated graphics AMD Radeon HD 7000 series
DDR3 dual channel SO-DIMM 1333/1600 max. up to 16GB
4 SATA-600 support RAID 0, 1 and 10
4 USB 3.0 supported
3 independent displays
DisplayPort 2 supports multi-stream
TPM 1.2 supported

MANO111 AMD Embedded R-Series APU Mini ITX SBC
2 Introduction
1.2 Specifications
CPU
AMD R-Series processor.
CPU Socket
AMD FS1r2 socket.
System Chipset
AMD A75 FCH.
BIOS
American Megatrends Inc. BIOS.
32Mbit SPI Flash, DMI, Plug and Play.
PXE Ethernet Boot ROM.
Support “Load Optimized Default”functionality to backup customized setting in BIOS
flash chip to prevent from CMOS battery failure.
System Memory
Two 204-pin unbuffered DDR3 SO-DIMM sockets.
Up to 16GB DDR3 1600MHz memory.
Onboard Multi I/O
Controller: Nuvoton NCT6627UD.
Serial ports: Three RS-232 ports, one RS-232/422/485 port and one TTL port.
USB Interface
Ten USB ports with fuse protection, comply with USB Spec. Rev.2.0.
Four USB 3.0 ports.
Serial ATA
Four SATA-600 with RAID 0, 1, and 10.
Display
One 40-pin connector for 18/24-bit single/dual channel LVDS and one 8-pin inverter.
Two DisplayPorts.
Two DVI-D ports via a stacked DVI-D connector.
Ethernet
LAN1 –Realtek RTL8111E Gigabit/Fast Ethernet.
LAN2 –Realtek RTL8111DP Gigabit/Fast Ethernet.
Audio
Realtek High Definition audio codec ALC662.
Support 2.1 channel audio line-out as six terminal 3.50mm earphone jack.
Expansion Interface
One PCI
One PCI-Express Mini Card socket which complies with PCI-Express Mini Card
Spec. v1.2.
One SIM Card slot
Power Management
ACPI (Advanced Configuration and Power Interface).

MANO111 AMD Embedded R-Series APU Mini ITX SBC
Introduction 3
Watchdog Timer
1~255 seconds; up to 256 levels.
Form Factor
170 x 170mm Mini ITX form factor.
Note
All specifications and images are subject to change without notice.
1.3 Utilities Supported
Chipset driver
AHCI driver
Ethernet driver
Audio driver
TPM driver

MANO111 AMD Embedded R-Series APU Mini ITX SBC
4 Introduction
This page is intentionally left blank.

MANO111 AMD Embedded R-Series APU Mini ITX SBC
Board and Pin Assignments 5
Chapter 2
Board and Pin Assignments
2.1 Board Dimensions and Fixing Holes
Top View

MANO111 AMD Embedded R-Series APU Mini ITX SBC
6 Board and Pin Assignments
Bottom View

MANO111 AMD Embedded R-Series APU Mini ITX SBC
Board and Pin Assignments 7
Side View

MANO111 AMD Embedded R-Series APU Mini ITX SBC
8 Board and Pin Assignments
2.2 Board Layout
Top View

MANO111 AMD Embedded R-Series APU Mini ITX SBC
Board and Pin Assignments 9
Bottom View

MANO111 AMD Embedded R-Series APU Mini ITX SBC
10 Board and Pin Assignments
2.3 Jumper Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following
illustration shows how to set up jumper.
Before applying power to MANO111 Series, please make sure all of the jumpers are in factory
default position. Below you can find a summary table and onboard default settings.
Note
Once the default jumper setting needs to be changed, please do it under power-off
condition.

MANO111 AMD Embedded R-Series APU Mini ITX SBC
Board and Pin Assignments 11
Jumper
Description
Setting
JP2
COM4 Data/Power Selection Default:
Default: RS-232 Data
CN3 Pin 1: DCD
3-5 close
CN3 Pin 8: RI
4-6 close
JP3
COM3 Data/Power Selection
Default: RS-232 Data
CN2 Pin 1: DCD
3-5 close
CN2 Pin 8: RI
4-6 close
JP4
COM2 Data/Power Selection
Default: RS-232 Data
CN1 Pin 1: DCD
3-5 close
CN1 Pin 8: RI
4-6 close
JP5
COM1 Data/Power Selection
Default: RS-232 Data
CN16 Pin 1: DCD
3-5 close
CN16 Pin 9: RI
4-6 close
JP6
TPM Normal Operation/Special Commands Selection
Default: Normal Operation
1-2 close
JP7
Auto Power On
Default: Enable
1-2 close
JP10
Restore BIOS Optimal Defaults
Default: Normal Operation
1-2 close
JP11
LVDS Brightness Control Mode Setting
Default: PWM Mode
1-2 close
JP12
+3.3V/+5V LVDS Voltage Selection
Default: +3.3V
1-2 close
JP13
(Optional)
+12V LVDS Voltage Selection
Open
JP14
COM1 RS-232/422/485 Mode Setting
Default: RS-232
1-2 close
JP15
3-5, 4-6 close
JP16
3-5, 4-6 close
JP17
DASH enable(default)
1-2 close
DASH disable
2-3 close

MANO111 AMD Embedded R-Series APU Mini ITX SBC
12 Board and Pin Assignments
2.3.1 COM4 Data/Power Selection (JP2)
The COM4 port has +5V level power capability on DCD and +12V level on RI by setting
this jumper.
2.3.2 COM3 Data/Power Selection (JP3)
The COM3 port has +5V level power capability on DCD and +12V level on RI by setting
this jumper.
2.3.3 COM2 Data/Power Selection (JP4)
The COM2 port has +5V level power capability on DCD and +12V level on RI by setting
this jumper.
2.3.4 COM1 Data/Power Selection (JP5)
The COM1 port has +5V level power capability on DCD and +12V level on RI by setting
this jumper. When COM1 is set to +5V or +12V level, please make sure the
communication mode is RS-232 (see section 2.3.10).
Function
Setting
Power: Set CN3 pin 1 to +5V level
1-3 close
Data: Set CN3 pin 1 to DCD (Default)
3-5 close
Power: Set CN3 pin 8 to +12V level
2-4 close
Data: Set CN3 pin 8 to RI (Default)
4-6 close
Function
Setting
Power: Set CN2 pin 1 to +5V level
1-3 close
Data: Set CN2 pin 1 to DCD (Default)
3-5 close
Power: Set CN2 pin 8 to +12V level
2-4 close
Data: Set CN2 pin 8 to RI (Default)
4-6 close
Function
Setting
Power: Set CN1 pin 1 to +5V level
1-3 close
Data: Set CN1 pin 1 to DCD (Default)
3-5 close
Power: Set CN1 pin 8 to +12V level
2-4 close
Data: Set CN1 pin 8 to RI (Default)
4-6 close
Function
Setting
Power: Set CN16 pin 1 to +5V level
1-3 close
Data: Set CN16 pin 1 to DCD (Default)
3-5 close
Power: Set CN16 pin 9 to +12V level
2-4 close
Data: Set CN16 pin 9 to RI (Default)
4-6 close

MANO111 AMD Embedded R-Series APU Mini ITX SBC
Board and Pin Assignments 13
2.3.5 TPM Normal Operation/Special Commands Selection (JP6)
Use JP6 for TPM normal operation or special commands selection.
2.3.6 Auto Power On (JP7)
If JP7 is enabled for AC power input, the system will be automatically power on without
pressing soft power button. If JP7 is disabled for AC power input, it is necessary to
manually press soft power button to power on the system.
Note
This function is similar to the feature of power on after power failure, which
is controlled by hardware circuitry instead of BIOS.
2.3.7 Restore BIOS Optimal Defaults (JP10)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this
procedure can restore BIOS optimal defaults.
2.3.8 LVDS Brightness Control Mode Setting (JP11)
The JP11 is enabled to select PWM or voltage control mode for inverter connector (CN8)
pin 8. These two control modes are for adjusting LVDS brightness.
Function
Setting
Normal operation (Default)
1-2 close
Special Commands Enable
2-3 close
Function
Setting
Enable auto power on (Default)
1-2 close
Disable auto power on
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
Function
Setting
PWM mode (Default)
1-2 close
Voltage mode
3-4 close

MANO111 AMD Embedded R-Series APU Mini ITX SBC
14 Board and Pin Assignments
2.3.9 LVDS Voltage Selection (JP12 and JP13)
The board supports voltage selection for flat panel displays. Use JP12 to set LVDS
connector (CN11) pin 1~6 VCCM to +3.3V or +5V voltage level. Use JP13 (optional) to
set LVDS connector (CN11) pin 1~6 VCCM to +12V voltage level. To prevent hardware
damage, before connecting please make sure that the input voltage of LVDS flat panel is
correct.
2.3.10 COM1 RS-232/422/485 Mode Setting (JP14, JP15, JP16)
Use these jumpers to set COM1 port to operate as RS-232, RS-422 or RS-485
communication mode. When these jumpers are set to operate as RS-422 or RS-485
mode, please make sure COM1 is on data mode (see section 2.3.4)
2.3.11 DASH Setting (JP17)
Function
JP12 Setting
+3.3V level (Default)
1-2 close
+5V level
2-3 close
Function
JP13 Setting
+12V level (Optional)
1-2 close
Function
Setting
RS-232 mode
(Default)
JP14 1-2 close
JP15 3-5, 4-6 close
JP16 3-5, 4-6 close
RS-422 mode
JP14 3-4 close
JP15 1-3, 2-4 close
JP16 1-3, 2-4 close
RS-485 mode
JP14 5-6 close
JP15 1-3, 2-4 close
JP16 1-3, 2-4 close
Function
Setting
DASH enable (Default)
1-2 close
DASH disable
2-3 close