AXIOMTEK CAPA322 User manual

CAPA322
Intel®Atom®x6413E and Intel®
Celeron®Processor J6412 and
Celeron®Processor N6210
3.5” Board
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
©Copyright 2022 Axiomtek Co., Ltd.
All Rights Reserved
June 2022, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please take care of the following jobs with precautions:
◼Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
◼Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. It discharges static electricity from your body.
◼Wear a wrist-grounding strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Intel®and Celeron®are trademarks of Intel Corporation.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions ...........................................................................................iii
Section 1 Introduction............................................. 1
1.1 Features ...............................................................................................2
1.2 Specifications......................................................................................2
1.3 Utilities Supported ..............................................................................3
Section 2 Board and Pin Assignments.................... 1
2.1 Board Dimensions and Fixing Holes .................................................1
2.2 Board Layout .......................................................................................3
2.3 Jumper and Switch Settings ..............................................................5
2.3.1 LVDS/eDP +3.3V/+5V/+12V Voltage Selection (JP1) ................................. 6
2.3.2 Restore BIOS Optimal Defaults (SW1) ....................................................... 6
2.3.3 Auto Power On (SSW1) .............................................................................. 6
2.4 Connectors ..........................................................................................7
2.4.1 I2C Connector (CN1) ................................................................................. 8
2.4.2 Fan Connector (CN2) .................................................................................. 8
2.4.3 Front Panel Connector (CN3) ..................................................................... 9
2.4.4 LVDS Connector (CN4) ............................................................................. 10
2.4.5 HD Audio Wafer Connector (CN5) ............................................................ 12
2.4.6 Inverter Connector (CN6).......................................................................... 12
2.4.7 Digital I/O Wafer Connector (CN7)............................................................ 13
2.4.8 SATA Power Connector (CN8) .................................................................. 13
2.4.9 eDP Connector (CN9) (Optional) .............................................................. 14
2.4.10 SIM Card Wafer Connector (CN10) .......................................................... 14
2.4.11 DisplayPort++ Connector (CN11).............................................................. 15
2.4.12 HDMI Connector (CN12)........................................................................... 15
2.4.13 ATX Power Connector (ATX1/ATX2)......................................................... 16
2.4.14 CMOS Battery Connector (BAT1) ............................................................. 16
2.4.15 COM Wafer Connectors (COM1~COM4).................................................. 17
2.4.16 Ethernet Ports (LAN1 and LAN2).............................................................. 18
2.4.17 SATA Connector (SATA1).......................................................................... 19
2.4.18 USB 2.0 Wafer Connector (USB1) ............................................................ 19
2.4.19 USB 3.2 Gen2 Type A Port (USB2)........................................................... 19
2.4.20 USB 2.0 Type A Port (USB3)..................................................................... 20
2.4.21 M.2 Key E Connector (SCN2) ................................................................... 21
2.4.22 Full-size PCI-Express Mini Card Connector (SCN3) ................................ 22
2.4.23 M.2 Key B Connector (SCN4) ................................................................... 23

v
Section 3 Hardware Description ........................... 25
3.1 Microprocessors ...............................................................................25
3.2 BIOS ...................................................................................................25
3.3 System Memory.................................................................................25
3.4 I/O Port Address Map........................................................................26
3.5 Interrupt Controller (IRQ) Map .........................................................27
3.6 Memory Map ......................................................................................32
Section 4 AMI BIOS Setup Utility.......................... 33
4.1 Starting...............................................................................................33
4.2 Navigation Keys ................................................................................33
4.3 Main Menu..........................................................................................35
4.4 Advanced Menu.................................................................................36
4.5 Chipset Menu.....................................................................................48
4.6 Security Menu....................................................................................50
4.7 Boot Menu..........................................................................................52
4.8 Save & Exit Menu ..............................................................................53
Appendix A Watchdog Timer................................... 55
A.1 About Watchdog Timer.....................................................................55
A.2 How to Use Watchdog Timer............................................................55
Appendix B Digital I/O ............................................. 57
B.1 About Digital I/O ................................................................................57
B.2 Digital I/O Programming ...................................................................57

vi
This page is intentionally left blank.

CAPA322 3.5” Board
Introduction 1
Section 1
Introduction
The CAPA322 is a 3.5” embedded board with Intel® Celeron® processor J6412 and N6210 &
Atom® x6413E processor that deliver outstanding system performance through
high-bandwidth interfaces, multiple I/O functions for interactive applications and various
embedded computing solutions.
It has one 260-pin unbuffered SO-DIMM socket for single channel DDR4 3200MHz memory
with maximum memory capacity up to 32GB. There are one Gigabit Ethernet port, one 2.5
Gigabit Ethernet, one SATA port with transfer rate up to 6Gb/s, two USB 3.2 Gen2 ports, and
four USB 2.0 ports that can achieve the best stability and reliability for industrial applications.
Additionally, it provides you with unique embedded features, such as four serial ports (two
RS-232/422/485 and two RS-232) and 3.5” form factor that applies an extensive array of PC
peripherals.

CAPA322 3.5” Board
2Introduction
1.1 Features
⚫Intel® Celeron® quad core J6412 processor (2.0GHz) and Celeron® dual core N6210
processor (1.2GHz)
⚫Intel® Atom®quad core x6413E processor (1.5GHz)
⚫1 DDR4 SO-DIMM supports up to 32GB memory capacity
⚫2 USB 3.2 Gen2 ports and 4 USB 2.0 ports
⚫1 PCI-Express Mini Cards with mSATA supported
⚫1 M.2 Key E and 1 M.2 Key B
1.2 Specifications
⚫CPU
◼Intel®Celeron®quad core J6412 2.0GHz.
◼Intel®Celeron®dual core N6210 1.2GHz.
◼Intel®Atom®quad core x6413E 1.5GHz
⚫Thermal Solution
◼Passive.
⚫Operating Temperature
◼-20°C~+70°C (Celeron processor SKU).
◼-40°C~+85°C (Atom processor SKU).
⚫BIOS
◼American Megatrends Inc. UEFI (Unified Extensible Firmware Interface) BIOS.
◼256Mbit SPI Flash, DMI, Plug and Play.
◼PXE Ethernet Boot ROM.
⚫System Memory
◼One 260-pin unbuffered DDR4 SO-DIMM socket.
◼Maximum up to 32GB DDR4 3200MHz memory capacity.
⚫Onboard Multi I/O
◼Serial Ports: Two RS-232/422/485 and two RS-232.
⚫Serial ATA
◼One SATA-600 connector.
◼One mSATA.
⚫USB Interface
◼Two USB 3.2 Gen2 ports on the rear I/O.
◼Two USB 2.0 ports on the rear I/O.
◼Two USB 2.0 ports in 2x5-pin internal wafer connector.
⚫Display
◼One 2x20-pin connector for 18/24-bit single/dual channel LVDS and one 8-pin
inverter connector. LVDS resolution is up to 1920x1200 in 24-bit dual channels.
◼One HDMI. The resolution is up to 4096x2160 @60Hz.
◼One DisplayPort. The resolution is up to 4096x2160 @60Hz.
◼(Optional, Co-layout with LVDS) One eDP. The resolution is up to 4096x2160
@60Hz.

CAPA322 3.5” Board
Introduction 3
⚫Trusted Platform Module (TPM)
◼Controller: ST ST33HTPH2X32AHD8 via SPI bus interface.
◼Complies with TPM2.0 main and PC client specification.
⚫Watchdog Timer
◼Timeout value range is 1~65535 seconds.
⚫Ethernet
◼One RJ-45 LAN port: Intel®I210-AT (I210-IT) supports 1000/100/10Mbps
Gigabit/Fast Ethernet with Wake-on-LAN and PXE Boot ROM.
◼One RJ-45 LAN port: Intel®I225-LM supports 2500/1000/100/10Mbps Gigabit/Fast
Ethernet with Wake-on-LAN and PXE Boot ROM.
⚫Audio
◼HD audio link without codec.
⚫Expansion Interface
◼One full-size PCI-Express Mini Card (with mSATA supported) complies with
PCI-Express Mini Card Spec. V1.2 (Optional).
◼One M.2 Key E connector in 22x30.
◼One M.2 Key B connector in 30x42 and 30x52.
⚫Power Input
◼One 2x2-pin connector.
◼+12V to +24V DC-in only.
◼Auto power on function supported.
⚫Power Management
◼ACPI (Advanced Configuration and Power Interface).
⚫Form Factor
◼3.5”form factor.
Note
All specifications and images are subject to change without notice.
1.3 Utilities Supported
⚫Chipset and graphics driver
⚫Ethernet driver
⚫Management Engine

CAPA322 3.5” Board
4Introduction
This page is intentionally left blank.

CAPA322 3.5” Board
Board and Pin Assignments 1
Section 2
Board and Pin Assignments
2.1 Board Dimensions and Fixing Holes
Top View

CAPA322 3.5” Board
2Board and Pin Assignment
Bottom View
Side View

CAPA322 3.5” Board
Board and Pin Assignments 3
2.2 Board Layout
Top View
Side View

CAPA322 3.5” Board
4Board and Pin Assignment
Bottom View

CAPA322 3.5” Board
Board and Pin Assignments 5
2.3 Jumper and Switch Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close. And remove jumper clip from 2 jumper pins to open. Below illustration
shows how to set up jumper.
Properly configure jumper and switch settings on the CAPA322 to meet your application
purpose. Below you can find a summary table of jumpers, switch and onboard default settings.
Note
Once the default jumper or switch setting needs to be changed, please do it under
power-off condition.
Jumper and Switch
Description
Setting
JP1
LVDS/eDP +3.3V/+5V/+12V Voltage Selection
Default: +3.3V
1-2 Close
SW1
Restore BIOS Optimal Defaults
Default: Normal Operation
Release
SSW1
Auto Power On
Default: Disable
1-2 Close

CAPA322 3.5” Board
6Board and Pin Assignment
2.3.1 LVDS/eDP +3.3V/+5V/+12V Voltage Selection (JP1)
The board supports voltage selection for flat panel displays. Use this jumper to set LVDS
connector (CN4) pin 1~6 VCCM / eDP connector (CN9) pin 1~4 LCD_VCC to +3.3V,
+5V or +12V level. To prevent hardware damage, before connecting please make sure
that the input voltage of flat panel is correct.
2.3.2 Restore BIOS Optimal Defaults (SW1)
Use SW1 to restore CMOS. To restore BIOS optimal defaults, press the tact switch for at
least 3 seconds, then release.
2.3.3 Auto Power On (SSW1)
If SSW1 is enabled for power input, the system will be automatically power on without
pressing soft power button. If SSW1 is disabled for power input, it is necessary to
manually press soft power button to power on the system.
Function
Setting
+12V level
5-6 close
+5V level
2-4 close
or
4-6 close
+3.3V level (Default)
1-2 close
Function
Setting
Normal (Default)
Release
Restore BIOS optimal defaults
Press
Function
Setting
Disable auto power on (Default)
1-2 close
Enable auto power on
2-3 close

CAPA322 3.5” Board
Board and Pin Assignments 7
2.4 Connectors
Signals go to other parts of the system through connectors. Loose or improper connection
might cause problems, please make sure all connectors are properly and firmly connected.
Here is a summary table of connectors on the hardware.
Connector
Description
CN1
I2C Connector
CN2
Fan Connector
CN3
Front Panel Connector
CN4
LVDS Connector
CN5
HD Audio Wafer Connector (Compatible with AX93A22)
CN6
Inverter Connector
CN7
Digital I/O Wafer Connector
CN8
SATA Power Connector
CN9 (Optional)
eDP Connector
CN10
SIM Card Wafer Connector (Compatible with AX93A19)
CN11
DisplayPort++ Connector
CN12
HDMI Connector
ATX1 (Optional)
ATX 90D Power Connector (Co-lay)
ATX2
ATX 180D Power Connector
BAT1
CMOS Battery Connector
COM1~COM2
COM1~COM2 Wafer Connectors (Support RS232/422/485)
COM3~COM4
COM3~COM4 Wafer Connectors (Support RS232)
LAN1
I210 Ethernet Port
LAN2
I225 Ethernet Port
SATA1
SATA Connector
USB1
USB 2.0 Wafer Port 4 and 5
USB2
USB 3.2 Gen2 Type A Port
USB3
USB 2.0 Type A Port
SCN2
M.2 Key E Connector
SCN3
Full-size PCI-Express Mini Card Connector
SCN4
M.2 Key B Connector
SDIMM1
DDR4 SO-DIMM Connector

CAPA322 3.5” Board
8Board and Pin Assignment
2.4.1 I2C Connector (CN1)
This is a 4-pin (pitch=1.25mm) connector for I2C interface which is compatible with
SMBus.
1 4
2.4.2 Fan Connector (CN2)
Cooling fan interface is available through this connector. You can find fan speed within
BIOS Setup Utility if fan is installed. For further information, see BIOS Setup Utility:
Advanced\Hardware Monitor\PC Health Status (see section 4.4).
1
Pin
Signal
1
I2C _CLK
2
I2C _DATD
3
I2C _ALERT_N
4
GND
Pin
Signal
1
GND
2
+12V level
3
Fan speed feedback
1

CAPA322 3.5” Board
Board and Pin Assignments 9
2.4.3 Front Panel Connector (CN3)
This is a 2x6-pin header (pitch=2.0mm) for front panel interface.
Internal Buzzer
Pin 1(-) and 2(+) connect the internal buzzer cable.
Power Status (PS-ON)
Pin 4 and pin 3 are PS-ON signal which are connected for knowing the power status of
this board.
Power LED
Pin 6 connects anode (+) of LED and pin 5 connects cathode(-) of LED. The power LED
lights up when the system is powered on.
Power On/Off Button
Pin 7 and 8 connect the power button on front panel to CPU board, which allows users to
turn on or off power supply.
System Reset Switch
Pin 9 and 10 connect the case-mounted reset switch that reboots your computer without
turning off the power switch. It is a better way to reboot your system for a longer life of
system power supply.
HDD Activity LED
This connection is linked to hard drive activity LED on the control panel. LED flashes
when HDD is being accessed. Pin 11 and 12 connect the hard disk drive to the front
panel HDD LED, pin 11 is assigned as cathode(-) and pin 12 is assigned as anode(+).
Pin
Signal
Pin
Signal
1
BUZZER-
2
BUZZER+
3
GND
4
PWR_PSON
5
PWRLED-
6
PWRLED+
7
PWRSW-
8
PWRSW+
9
HW RST-
10
HW RST+
11
HDDLED-
12
HDDLED+

CAPA322 3.5” Board
10 Board and Pin Assignment
2.4.4 LVDS Connector (CN4)
This board has a 2x20-pin connector which is compliant with JST SM40B-SRDS-G-TF
for LVDS LCD interface. It is strongly recommended to use the matching connector JST
SHDR-40VS-B. Pin 1~6 VCCM can be set to +3.3V, +5V or +12V by setting JP1 (see
section 2.3.1).
Note
[*]: When making LVDS cable, pin 2 of JST SHDR-40VS-B connector should
match pin 1 of CN4.
18-bit single channel
Pin
Signal
Pin
Signal
1
VCCM
2
VCCM
3
VCCM
4
VCCM
5
VCCM
6
VCCM
7
N.C.
8
N.C.
9
GND
10
GND
11
N.C.
12
N.C.
13
N.C.
14
N.C.
15
GND
16
GND
17
N.C.
18
N.C.
19
N.C.
20
N.C.
21
GND
22
GND
23
Channel A D0-
24
N.C.
25
Channel A D0+
26
N.C.
27
GND
28
GND
29
Channel A D1-
30
N.C.
31
Channel A D1+
32
N.C.
33
GND
34
GND
35
Channel A D2-
36
Channel A CLK-
37
Channel A D2+
38
Channel A CLK+
39
GND
40
GND