AXIOMTEK SHB212 Series User manual

Product User Manual
and enterprise branch and head offices
SHB212
$;,207(.
www.enochsystems.com 1-877-722-1116 [email protected]
Copyright © 2013 Enoch Systems, LLC, Enoch Systems and the Enoch Systems logo are trademarks or registered trademarks of Enoch Systems, LLC and/or its affiliates in the U.S. and other countries.
Third-party trademarks mentioned are the property of their respective owners. All rights reserved.

SHB212 Series
IntelAtom™ Processor
PICMG 1.3 Half-Size
Single Board Computer
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. Axiomtek Co., Ltd. assumes no responsibility for
any infringements of patents or any third party‟s rights, and any
liability arising from such use.
Axiomtek does not warrant or assume any legal liability or
responsibility for the accuracy completeness or usefulness of any
information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or
product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of Axiomtek Co., Ltd.
Caution
If you replace wrong batteries, it causes the danger of explosion. It is
recommended by the manufacturer that you follow the manufacturer‟s
instructions to only replace the same or equivalent type of battery,
and dispose of used ones.
Copyright 2011 Axiomtek Co., Ltd.
All Rights Reserved
April 2011, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity.
To prevent chipsets from electrostatic discharge damage, please take
care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them
Before holding the board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. It discharges
static electricity from your body.
Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI is a registered of American Megatrends Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel®and Atom™ are trademarks of Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered
brands of their respective owners.

iv
Table of Contents
CHAPTER 1 INTRODUTION............................................................ 1
1.1 Specifications........................................................................ 2
1.2 Utilities Supported................................................................. 3
CHAPTER 2 JUMPERS AND CONNECTORS................................ 5
2.1 Board Dimensions and Fixing Holes .................................... 5
2.2 Board Layout......................................................................... 7
2.3 Jumper Settings.................................................................... 9
2.3.1 COM1 RS-232/422/485 Mode Select (JP1, JP2, JP3)10
2.3.2 COM1 Data / Power Mode Selection (JP6) ................ 11
2.3.3 COM2 Data / Power Mode Selection (JP5) ................ 12
2.3.4 HD Audio Line Out / Speaker Out Select (JP4).......... 13
2.3.5 CMOS Clear (JP7)...................................................... 13
2.3.6 Power On Control Mode (JP8).................................... 14
2.3.7 USB0,1/USB2,3/USB4,5 Port Power Selection
(JP12,JP14,JP10)....................................................... 14
2.3.8 CompactFlashTM Type Selection (JP11)..................... 15
2.3.9 LVDS LCD Type Support Selection (JP13) ................ 15
2.4 Connectors.......................................................................... 16
2.4.1 Front Panel Connector (CN1)..................................... 17
2.4.2 Parallel Port Connector (CN2).................................... 18
2.4.3 High Definition Audio Connector (CN3)...................... 19
2.4.4 EPIC Power Connector (CN4) .................................... 19
2.4.5 SMBus Connector (CN5) ............................................ 20
2.4.6 LVDS LCD Connector (CN6) ...................................... 20
2.4.7 LVDS LCD Backlight Connector (CN7) ...................... 21
2.4.8 Serial Port 1 Connector (COM1)................................. 22
2.4.9 Serial Port 2 Connector (COM2)................................. 23
2.4.10CPU & System Fan Connectors (FAN1, FAN2) ......... 23
2.4.11PS/2 Keyboard Internal Connector (KB1)................... 24
2.4.12PS/2 Mouse Internal Connector (MS1)....................... 24
2.4.13LAN RJ45 Connector (LAN1, LAN2) .......................... 25
2.4.14SATA Connectors (SATA1, SATA2)........................... 25
2.4.15CompactFlashTM Socket (SCF1)................................. 26
2.4.16USB Connector (USB1, USB2)................................... 28
2.4.17USB Connector (USB3, USB4)................................... 28
2.4.18VGA Connector (VGA1).............................................. 29
CHAPTER 3 HARDWARE DESCRIPTION.................................... 31

v
3.1 Microprocessors ................................................................. 31
3.2 BIOS ................................................................................... 31
3.3 System Memory.................................................................. 31
3.4 I/O Port Address Map......................................................... 32
3.5 Interrupt Controller.............................................................. 34
3.6 Memory Map....................................................................... 36
CHAPTER 4 AMI BIOS UTILITY.................................................... 39
4.1 Starting................................................................................ 39
4.2 Navigation Keys.................................................................. 39
4.3 Main Menu.......................................................................... 41
4.4 Advanced Menu.................................................................. 42
4.5 Boot Menu........................................................................... 54
4.6 Security Menu..................................................................... 58
4.7 Chipset Menu...................................................................... 59
4.8 Exit Menu............................................................................ 63
APPENDIX A WATCHDOG TIMER................................................ 65
Watchdog Timer Setting............................................................. 65
Using the Watchdog Function.................................................... 66

vi
MEMO:

SHB212 PICMG1.3 Half-Size SBC User’s Manual
INTRODUCTION
1
CHAPTER 1
INTRODUCTION
The SHB212 is a PICMG1.3 half-size Single Board Computer to
support Intel® Atom™ processor N455/D425/D525. The board
integrates chipset ICH8-M that delivers outstanding system
performance through high-band width interfaces, multiple I/O
functions for interactive applications and various embedded
computing solutions. There is one 204-pin unbuffered SO-DIMM
socket for single channel DDR3-667/800 MHz memory, maximum
memory capacity up to 4GB. (N455 is only for DDR3-667, maximum
memory capacity up to 2GB). It also features two Gigabit/Fast
Ethernet, two Serial ATA channels for total two Serial ATA hard drives
at maximum transfer rate up to 150/300MB/sec, six USB 2.0 high
speed compliant, built-in High Definition Audio Codec that can
achieve the best stability and reliability for industrial applications.

SHB212 PICMG1.3 Half-Size SBC User’s Manual
INTRODUCTION
2
1.1 Specifications
CPU
Intel®AtomTM processor N455/D425/D525
System Chipset
Intel®ICH8M
BIOS
American Megatrends Inc. BIOS.
16Mbit SPI Flash
PXE Ethernet Boot ROM.
System Memory
One 204-pin unbuffered DDR3 SO-DIMM sockets
Maximum to 4GB DDR3 667/800 MHz memory for D425/D525
Maximum to 2GB DDR3 667 MHz memory for N455
IDE Interface
One CompactFlash™ Type II Socket
Two SATA-150/300 connectors
USB Interface
Six USB ports compliant with USB Spec. Rev. 2.0 (two on the
rear I/O, and four ports via wafer connectors)
Onboard Multi I/O
Controller: Winbond W83627DHG
One 26-pin 2.0 pitch box-header for Parallel port
One for RS-232/422/485 (COM1) and one port for RS-232
(COM2)
Display
Support CRT and LVDS LCD output
15-pin D-Sub connector as VGA connector
One 40-pin connector for 18 bit single channel LVDS and one
7-pin inverter connector

SHB212 PICMG1.3 Half-Size SBC User’s Manual
INTRODUCTION
3
Expansion Interface
One PCIe x4 or four PCIe x1 I/O Deivces
There is no PCIex16 signal.
Watchdog Timer
1~255 seconds; up to 255 levels
Ethernet
One port with INTEL 82567V for Gigabit/Fast Ethernet
One port with INTEL 82574L for Gigabit/Fast Ethernet
Audio
HD Audio compliant via Realtek ALC662
Speaker-out/line-out & Line-in & MIC-in via Box Header
connector
Power Management
ACPI (Advanced Configuration and Power Interface)
Dimensions
185mm x 126.39mm
All specifications and images are subject to change without notice.
1.2 Utilities Supported
Chipset Driver
Graphic Driver
Ethernet Driver
Audio Driver
AHCI Driver

SHB212 PICMG1.3 Half-Size SBC User’s Manual
INTRODUCTION
4
MEMO :

SHB212 PICMG1.3 Half-Size SBC User’s Manual
JUMPERS AND CONNECTORS
5
CHAPTER 2
JUMPERS AND CONNECTORS
2.1 Board Dimensions and Fixing Holes
Top Side

SHB212 PICMG1.3 Half-Size SBC User’s Manual
JUMPERS AND CONNECTORS
6
Bottom Side

SHB212 PICMG1.3 Half-Size SBC User’s Manual
JUMPERS AND CONNECTORS
7
2.2 Board Layout
Top Side

SHB212 PICMG1.3 Half-Size SBC User’s Manual
JUMPERS AND CONNECTORS
8
Bottom Side

SHB212 PICMG1.3 Half-Size SBC User’s Manual
JUMPERS AND CONNECTORS
9
2.3 Jumper Settings
Proper jumer settings configure the SHB212 to meet your application
purpose. We are here with listing a summary table of all jumpers and
default settings for onboard devices, respectively.
Jumper
Description
Jumper Setting
JP1
COM1 RS-232/422/485 setting
Default：RS-232
Short 1-2
JP2
COM1 RS-232/422/485 setting
Default：RS-232
Short 3-5、4-6
JP3
COM1 RS-232/422/485 setting
Default：RS-232
Short 3-5、4-6
JP4
HD Audio Line Out / Speaker Out Select
Default：Line Out
Short 1-3、2-4
JP5
COM2 Data/Power Mode Select
Default：RS-232 Data
Short 7-9、8-10
JP6
COM1 Data/Power Mode Select
Default：Standby Power Mod
Short 7-9、8-10
JP7
CMOS Clear
Default：Normal Operation
Short 1-2
JP8
Power On Control Mode
Default：Power On control by Front Panel
Connector
Short 1-2
JP10
USB 4,5 Port Power(5V) Selection
Default：Standby Power Mode
Short 2-3
JP11
CompactFlashTM Type Selection
Default：3.3V type CompactFlashTM
Support
Short 1-2
JP12
USB 0,1 Port Power(5V) Selection
Default：Main Power Mode
Short 1-2
JP13
LVDS LCD Type Support Selection
Default：3.3V type LVDS LCD Support
Short 1-2
JP14
USB 2,3 Port Power(5V) Selection
Default：Standby Power Mode
Short 2-3

SHB212 PICMG1.3 Half-Size SBC User’s Manual
JUMPERS AND CONNECTORS
10
2.3.1 COM1 RS-232/422/485 Mode Select (JP1, JP2,
JP3)
These jumpers select the communication mode of COM1 port to
operate RS-232 or RS-422 or RS-485. When these jumpers are
selected to operate RS-422 or RS485, please make sure the COM1 is
on Data mode.
Function
Jumper Setting
JP1
JP2
JP3
RS-232
(Default)
RS-422
RS-485

SHB212 PICMG1.3 Half-Size SBC User’s Manual
JUMPERS AND CONNECTORS
11
2.3.2 COM1 Data / Power Mode Selection (JP6)
The COM1 port have +5V or +12V level power capability on DCD and
+5V or +12V level power capability for RI, depending on the JP6
setting.
Function
Jumper Setting
COM1 Pin 1 is +12V level
COM1 Pin 1 is +5V level
COM1 Pin1 is DCD
(Default)
COM1 Pin 8 is +12V level
COM1 Pin 8 is +5V level
COM1 Pin 8 is RI
(Default)

SHB212 PICMG1.3 Half-Size SBC User’s Manual
JUMPERS AND CONNECTORS
12
2.3.3 COM2 Data / Power Mode Selection (JP5)
The COM2 port have +5V or +12V level power capability on DCD and
+5V or +12V level power capability for RI, depending on the JP5
setting.
Function
Jumper Setting
COM2 Pin 1 is +12V level
COM2 Pin 1 is +5V level
COM2 Pin 1 is DCD
(Default)
COM2 Pin 8 is +12V level
COM2 Pin 8 is +5V level
COM2 Pin 8 is RI
(Default)

SHB212 PICMG1.3 Half-Size SBC User’s Manual
JUMPERS AND CONNECTORS
13
2.3.4 HD Audio Line Out / Speaker Out Select (JP4)
This jumper is to select which source for the audio output (CN3). When
the Speaker Out is set, it delivers 2W/channel continuous into 8 Ohm
loads.
Function
Jumper Setting
Line Out
(Default)
Speak Out with Amplifier
2.3.5 CMOS Clear (JP7)
You may need to use this jumper is to clear the CMOS memory if
incorrect settings in the Setup Utility.
Function
Jumper Setting
Normal
(Default)
Clear CMOS