AXIOMTEK SHB211 Series User manual

SHB211 Series
Intel®Core™2 Duo/Celeron®M CPU
PICMG 1.3 Half-Size
Single Board Computer
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is
recommended by the manufacturer that you follow the manufacturer’s
instructions to only replace the same or equivalent type of battery,
and dispose of used ones.
©Copyright 2009 AXIOMTEK Co., Ltd.
All Rights Reserved
April 2009, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity.
To prevent chipsets from electrostatic discharge damage, please take
care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
Before holding the board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. It
discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI®is a registered trademark of American Megatrends Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel®CoreTM 2 Duo / Celeron®M are trademarks of Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered
brands of their respective owners.

iv
Table of Contents
Disclaimers........................................................................................................... ii
ESD Precautions ................................................................................................. iii
CHAPTER 1 INTRODUCTION..................................................................................... 1
1.1 Specifications................................................................................... 2
1.2 Utilities Supported............................................................................ 4
1.3 Block Diagram.................................................................................. 5
1.4 I/O Bracket ....................................................................................... 6
CHAPTER 2 JUMPERS AND CONNECTORS............................................................ 7
2.1 Board Dimensions............................................................................ 7
2.2 Board Layout.................................................................................... 8
2.3 Jumper Settings ............................................................................. 10
2.3.1 COM1 Mode Select Jumpers (JP1, JP2, JP3)............................... 11
2.3.2 Audio Output Selection Jumper (JP4)............................................ 11
2.3.3 COM1~2 Mode Selection Jumpers (JP6, JP5) .............................. 12
2.3.4 CompactFlash™ Device Setting Jumper (JP8~11)........................ 14
2.3.5 ComplactFlash™ Voltage Selection Jumper (JP12)...................... 14
2.3.6 Auto-Power Button Selection Jumper (JP13)................................. 14
2.3.7 USB Voltage Selection Jumpers (JP14, JP15, JP17).................... 15
2.3.8 LVDS Voltage Selection Jumper (JP18) ........................................ 15
2.3.9 CMOS Clear Jumper (JP19) .......................................................... 16
2.3.10 NB PCIex16 Signal Mode Jumper (JP20-21)................................ 16
2.4 Connectors..................................................................................... 17
2.4.1 Audio Connector (CN1).................................................................. 19
2.4.2 Front Panel Connector (CN2)......................................................... 19
2.4.3 Print Port or Floppy Connectors (CN3) .......................................... 21
2.4.4 EPIC Power Connector (CN4)........................................................ 22
2.4.5 CPU & System Fan Connectors (CN5, CN7, CN8)........................ 23
2.4.6 SMBUS Connector (CN6) .............................................................. 23
2.4.7 Display Port Connector (SHB211PGGA, CN9)............................. 24
2.4.8 VGA Connector (SHB211VGGA, CN10)........................................ 25
2.4.9 JST Connector for LVDS Flat Panel (CN11).................................. 25
2.4.10 LVDS Backlight Connector (CN12)................................................ 26
2.4.11 External Mouse/Keyboard Connectors (MS1/KB1)........................ 27
2.4.12 Ethernet RJ-45 Connectors (LAN1/LAN2)..................................... 27
2.4.13 Serial Port Interface (COM1, COM2)............................................. 28
2.4.14 SATA Connectors (SATA1, SATA2) .............................................. 28
2.4.15 USB Connectors (USB1, USB2) .................................................... 29
2.4.16 USB Connectors (USB3/USB4)..................................................... 29
2.4.17 USB Connectors (USB5/USB6)..................................................... 30
2.4.18 CompactFlashTM Socket (SCF1).................................................... 30
CHAPTER 3 HAREDWARE INSTALLATION............................................................ 32
3.1 Installing the Processor.................................................................. 32
3.2 Installing the Memory..................................................................... 35

v
CHAPTER 4 HARDWARE DESCRIPTION................................................................ 36
4.1 Microprocessors............................................................................. 36
4.2 BIOS............................................................................................... 36
4.3 System Memory ............................................................................. 36
4.4 I/O Port Address Map..................................................................... 37
4.5 Interrupt Controller (IRQ) Map........................................................ 39
CHAPTER 5 AMI BIOS SETUP UTILITY................................................................... 40
5.1 Starting........................................................................................... 40
5.2 Navigation Keys ............................................................................. 40
5.3 Main Menu...................................................................................... 41
5.4 Advanced Menu ............................................................................. 42
5.5 PCI PnP Menu................................................................................ 58
5.6 Boot Menu...................................................................................... 60
5.7 Security Menu ................................................................................ 62
5.8 Chipset Menu................................................................................. 64
5.9 Exit Menu ....................................................................................... 67
CHPATER 6 INSTALLATION OF DRIVERS ............................................................. 70
6.1 Installing Chipset Driver ................................................................. 70
6.2 Installing AUDIO Driver.................................................................. 74
6.3 Installing VGA Driver...................................................................... 76
6.4 Installing LAN Driver....................................................................... 80
APPENDIX A WATCHDOG TIMER ........................................................................... 84
Watchdog Timer Setting.................................................................................... 84
Using the Watchdog Function .......................................................................... 84
APPENDIX B PICMG v1.3 INTERFACE DEFINITION............................................ 86
APPENDIX C CONFIGURING SATA FOR RAID FUNCTION................................... 91

vi
MEMO

SHB211 Socket P Half-Size SBC User’s Manual
Introduction 1
CHAPTER 1 INTRODUCTION
The SHB211 PICMG 1.3 half-size Single Board Computer supports
Socket P (478-pin) for Intel®Core™2 Duo/Celeron®M processors
with FSB 800/1066 MHz MT/s. The board integrates Intel®GM45 and
ICH9M/ICH9M-E chipsets that can deliver outstanding system
performance through high-bandwidth interfaces, multiple I/O functions
for interactive applications and various embedded computing
solutions. There are two 204-pin DDR3 SODIMM sockets for dual
channel DDR3 800/1066, maximum memory capacity up to 8GB. The
board also features dual Gigabit Ethernet, two serial ATA ports at
maximum transfer rate up to 3Gbs, and RAID 0,1,5,10 (optional with
ICH9M-E). Six USB 2.0 high speed compliant ports and built-in Intel®
HD Audio Digital Header can achieve the best stability and reliability
for industrial applications.

SHB211 Socket P Half-Size SBC User’s Manual
Introduction
2
1.1 Specifications
zCPU
Intel®Core™2 Duo/Celeron®M Processors
zSystem Chipset
Intel®GM45 and ICH9M (optional with ICH9M-E)
zCPU Socket
Socket P (478-pin)
zFront-Side Bus
800/1066 MHz
zBIOS
AMI BIOS via SPI interface with socket
zSystem Memory
Two 204-pin DDR3 SO-DIMM sockets
Maximum up to 8GB DDR3 memory
Supports DDR3 800/1066 memory
zL2 Cache: integrated in CPU
zOnboard Multi-I/O
Parallel Port: one 26-pin 2.0 pitch box-header for shared
FDD/LPT
Serial Port: one for RS-232/422/485 (COM1) and one port
for RS-232 (COM2)
Two Serial ATA-2 ports
zUSB Interface
Six USB ports compliant with USB Spec. Rev. 2.0 (two on
the rear I/O, and four ports via wafer connectors)
zExpansion Interface
PCIe x16 for discrete graphic card or PCIe x1 deivces
PCIe x4 for one PCIe x4 or four PCIe x1 I/O Deivces
LPC interface
zSSD
CompactFlash™Type-II Socket via jMicron JM20330
SATA-to-PATA controller

SHB211 Socket P Half-Size SBC User’s Manual
Introduction 3
zVGA Controller
Chipset -- Intel®GM45 GMCH Gen5 integrated graphic
engine; support Microsoft DirectX 10, Blu-ray 40Mb/s
Memory Size up to 256MB frame buffer sharing system
memory
Maximum Resolution –
◆ CRT – 2048 x 1536 @ 75Hz with 32-bit color
◆ LVDS LCD – 4:3 up to UXGA 1600 x 1200
◆ Digital DisplayPort – 2048 x 1536
Output Interface --
◆ CRT connector for DAC output
◆ DisplayPort connector (co-location with CRT D-Sub 15-
pin connector as an option)
◆ LVDS LCD with single/dual channel 18/24-bit mode
zEthernet
Dual Gigabit Ethernet; 2 x RTL8111B
zSerial ATA
Support Serial ATA/Serial ATA II
Two Serial ATA-II ports, 3Gb/s performance and RAID
0,1,5,10 (optional with ICH9M-E)
zAudio
Intel®HD Audio Digital Header
zHardware Monitoring
Support CPU/System temperature, CPU/System voltage,
and CPU/System Smart Fan features
zWatchdog Timer
Reset Supported (1-255 level)
zDimensions
185mm x 126mm

SHB211 Socket P Half-Size SBC User’s Manual
Introduction
4
NOTE All specifications and images are subject to change without
notice.
1.2 Utilities Supported
zIntel®GM45 Utility and Drivers
zVGA Drivers
zEthernet Utility and Drivers
zRAID Utility

SHB211 Socket P Half-Size SBC User’s Manual
Introduction 5
1.3 Block Diagram

SHB211 Socket P Half-Size SBC User’s Manual
Introduction
6
1.4 I/O Bracket

SHB211 Socket P Half-Size SBC User’s Manual
Jumpers and Connectors 7
CHAPTER 2 JUMPERS AND CONNECTORS
2.1 Board Dimensions

SHB211 Socket P Half-Size SBC User’s Manual
Jumpers and Connectors
8
2.2 Board Layout
Component Side

SHB211 Socket P Half-Size SBC User’s Manual
Jumpers and Connectors 9
Solder Side

SHB211 Socket P Half-Size SBC User’s Manual
Jumpers and Connectors
10
2.3 Jumper Settings
Proper jumper settings configure the SHB211 to meet your application
purpose.
Jumper Default Setting Jumper Setting
JP1 COM1 Mode Selection
Default: RS-232 Short 1-2
JP2 COM1 Mode Selection
Default: RS-232 Short 3-5, 4-6
JP3 COM1 Mode Selection
Default: RS-232 Short 3-5, 4-6
JP4 Audio Speak Out/Line Out Selection
Default: Line Out Short 1-3, 2-4
COM2 Pin 1: DCD Short 7-9
JP5 COM2 Mode Select COM2 Pin 8: RI Short 8-10
COM1 Pin 1: DCD Short 7-9
JP6 COM1 Mode Select COM1 Pin 8: RI Short 8-10
JP8~11 CF Device
Default: ON Short 1-2
JP12 Compact Flash Voltage Selection
Default: 3.3V Short 1-2
JP13 Auto-Power Button Selection
Default: Manual Power Button Short 1-2
JP14 USB1,2 Voltage Selection
Default: 5V Short 1-2
JP15 USB3,4 Voltage Selection
Default: 5V_SBY Short 2-3
JP16
Digital Displayport only or concurrent with
PCIE (SHB211 PGGA )
Default: Digital Displayport concurrent with
PCIE
Short 1-2
JP17 USB5,6 Voltage Selection
Default: 5V_SBY Short 2-3
JP18 LVDS Voltage Selection
Default: 3.3V Short 1-2
JP19 Normal Operation/Clear CMOS setting
Default: Normal Operation Short 1-2

SHB211 Socket P Half-Size SBC User’s Manual
Jumpers and Connectors 11
Jumper Default Setting Jumper Setting
JP20~21 NB PCIEx16 Signal MODE
Default: PCIEx16 Short 2-3
-- The End --
2.3.1 COM1 Mode Select Jumpers (JP1, JP2, JP3)
These jumpers select the COM1 port’s communication mode to
operate RS-232 or RS-422/485.
Description Function Jumper Setting
RS-232
(Default) JP1
JP2 JP3
RS-422 JP1 JP2
JP3
COM1
RS-485 JP1 JP2
JP3
2.3.2 Audio Output Selection Jumper (JP4)
This jumper makes the selection of Audio output.
Description Function Jumper Setting
Line Out
(Default)
Audio Line Out/
Speaker Out
Speak Out

SHB211 Socket P Half-Size SBC User’s Manual
Jumpers and Connectors
12
2.3.3 COM1~2 Mode Selection Jumpers (JP6, JP5)
These jumpers select the COM1, COM2 ports’DCD and RI mode.
Description Function Jumper Setting
Pin 1=12V
Pin 1=5V
*Pin 1=DCD
(Default)
Pin 8=12V
Pin 8=5V
COM1 DCD & RI
Voltage Selection
(JP6)
*Pin 8=RI
(Default)

SHB211 Socket P Half-Size SBC User’s Manual
Jumpers and Connectors 13
Description Function Jumper Setting
Pin 1=12V
Pin 1=5V
*Pin 1=DCD
(Default)
Pin 8=12V
Pin 8=5V
COM2 DCD & RI
Voltage Selection
(JP5)
*Pin 8=RI
(Default)

SHB211 Socket P Half-Size SBC User’s Manual
Jumpers and Connectors
14
2.3.4 CompactFlash™Device Setting Jumper (JP8~11)
Jumper Description Jumper Setting Description Jumper Setting
CF Device
Enable (Default) Disable
2.3.5 ComplactFlash™Voltage Selection Jumper
(JP12)
This jumper is to select the voltage for CompactFlashTM interface.
Description Function Jumper Setting
3.3V (Default)
CompactFlashTM
Voltage Selection
5V
2.3.6 Auto-Power Button Selection Jumper (JP13)
Use this jumper to select either Auto or Manual power button.
Description Function Jumper Setting
Manual Power
Buttom
(Default)
Auto-Power Button
Selection
Automatic
Power Button