Axminster AW370WL User manual

AW370WL
Woodturning Lathe
Code 107700
Original Instructions
AT: 29/01/2021
BOOK VERSION: 03

Index of Contents
2
EU Declaration of Conformity
Specification
Model AW370WL
Rating Workshop
Power 750W
Speed 500-2,000rpm
Spindle Taper 2MT
Spindle Thread 1” x 8tpi (ref T04M)
Taper Tailstock 2MT
Distance Between Centres 1,100 mm (43.3”)
Max Diameter over Bed 370 mm
Tool Rest Stem Diameter 25 mm
Overall L x W x H 1,680 x 470 x 1,155 mm
Weight 97 kg
The symbols below advise the correct safety procedures when using this machine.
Fully read manual
and safety instructions
before use
Eye protection
should be worn
Ear protection
should be worn
HAZARDDust mask
should be worn
EU Declaration of Conformity 02
Specification 02
General Safety Rules 03-04
Specific Safety Rules for Wood Lathes 05-06
Electrical Information 06-07
Know your Wood Lathe 08
Unpacking Contents 9
Assembly 10-11
Adjustments 12
Operation 13-14
Maintenance 14-15
Exploded Diagrams/Lists 16-17
Cert No: MC1100
Axminster Tool Centre Ltd
Axminster Devon
EX13 5PH UK
axminstertools.com
Type Lathe (Wood Lathe)
Model AW370WL conforms to the machinery example for which the
EC Type-Examination Certificate No AE 50390140, AE 50398334, AM 50307837, AN 50170711
has been issued by Laizhou Planet Machinery Co., Ltd.
at: Yutai West Street Laizhou, Shandong 261400 China
and complies with the relevant essential health and safety requirements.
2006/42/EC
2006/95/EC - Annex I
EN 55014-1:2017
EN 55014-2:2015
declares that the machinery described:-
This machine complies with the following directives:
EU Declaration of Conformity
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 55014-1:2006+A1+A2
EN 55014-2:1997+A1+A2
Signed
Andrew Parkhouse
Operations Director Date: 22/01/2018

General Safety Rules
3

General Safety Rules
4

Specific Safety Rules for Wood Lathes
5

Specific Safety Rules for Wood Lathes
6
Electrical Information

Electrical Information
7

Know your Wood Lathe
8

Unpacking Contents
9

Assembly
10

Assembly
11

Adjustments
12

Operation
13

Operation
14
Maintenance

Maintenance
15
Lubricating the drive shaft
Over time the spindle drive on the Variomatic’
speed control assembly will need lubricating to
prevent the moving pulleys from seizing. It is
recommend to check and lubricate the shaft on
a regular basis.
1) Remove the four dome head screws holding the
head stock cover in place. Remove cover, clean the
pulley mechanism and remove any build up resin
debris. Use a push type grease gun for chainsaw
sprocket nose guide bar. Place it over the grease
nipple to the end of the motor drive shaft & pump
in grease several time until you see it emage over
spring assembly. Re-fit the cover and secure in
place.
Remove the four dome
screws holding the
cover
Grease gun for chainsaw
sprocket nose guide bar
1
3
4
5
2
Pump grease into the shaft serveral times, you will see
grease emerge from the spring.
2) Spray ambersil PTFE film anti-stick over the lathes
spindle shaft & Swivel mechanisum this will help to
reduce friction and to help prevent it from corroding.
PUMP Grease into shaft
Grease nipple

Exploded Diagrams/Lists
16

Exploded Diagrams/Lists
17
NO. DESCRIPTION Q’TY
1 HEADSTOCK 1
2 FACEPLATE 1
3 HEADSTOCK SPUR 1
4 SPINDLE 1
5KEY 1
6 BEARING 2
7 “C”RING 2
8 SPRING 1
9 BRACKET-SHIFTING LEVER 1
10 “CRING 1
11 “C”RING 1
12 “CRING 1
13 MOTOR 1
14 KEY 1
15 SCREW 1
16 COVER-MOTOR 1
17 PULLEY-MOTOR(RIGHT) 1
18 PULLEY-MOTOR(LEFT) 1
19 SPRING 1
20 SLEEVE 1
21 “CRING 2
22 PUSH-OUT ROD 1
23 LEVER 1
24 “CRING 3
25 ECCENTRIC ROD 1
26 SCREW 1
27 “CRING 1
28 PULLEY-SPINDLE(LEFT) 1
29 V-BELT 1
30 PULLEY-SPINDLE(RIGHT) 1
31 BEARING 1
32 NUT-LOCK 1
33 NUT 9
34 CLAMP 2
35 NUTM4 2
36 “CRING 1
37 TURNING BASE 1
38 BED 1
39 BAFFLE 2
40 SCREW 4
41 HEX WRENCH 4
42 BOLT-A 1
43 CLAMP-A 1
44 HEX NUT 3
45 ANGULAR SETTING ASSEMBLY 1
46 SCREW 2
47 SPRING WASHER 2
48 GEAR ASSEMBLY 1
49 SPEED LABLE 1
51 HEX SCREW 3
52 BACK 1
53 BOLT-B 2
54 CLAMP-B 2
55 ECCENTRIC ROD 1
56 TOOL REST BODY 1
57 HANDLE ASSEMBLY 2
58 EXTENSION TOOL REST 1
59 LOCK HANDLE-TAILSTOCK 1
60 TOOL REST 1
61 TAILSTOCK SPUR 1
62 TAIL SPINDLE 1
63 TAIL STOCK SCREW 1
64 HANDLE ASSEMBLY 1
65 TAILSTOCK 1
66 WASHER 1
67 HANDLE WHEEL 1
68 SCREW 1
69 SCREW 1
70 SWITCH BOX 1
71 SWITCH 1
72 SWITCH BOX PLATE 1
73 SCREW 2
74 COVER 1
75 SPRING WASHER 8
76 POWER CORD 1
77 MOTOR POWER WIRE 1
78 NUT 20
79 WASHER 20
80 CARRIAGE BOLT STAND 20
81 STAND UPPER COVER 2
82 STAND LEG--I 2
83 STAND LEG--II 2
84 TOOL TABLE 1

The Axminster guarantee
Buy with confidence from Axminster!
So sure are we of the quality, we cover all parts and labour free of charge for three years!
For more information visit axminstertools.com/3years
Axminster Tools, Axminster Devon EX13 5PH
axminstertools.com
The packaging is suitable for recycling.
Please dispose of it in a responsible manner.
Do not dispose of electric tools together with household waste material.
By law they must be collected and recycled separately.
EU Countries Only