Axor Montreux 16815007 Manual

INSTALLATION
ZH ⁄ 用户手册 ⁄ 组装说明 02
EN ⁄ Instructions for use ⁄ assembly instructions 04
Lesezeichen
中文 02
English 04
AXOR Montreux
168150 07
AXOR Shower Select Soft Cube
3 6 711 0 0 7
AXOR Shower Select Square
36718007

02
ZH
安全技巧
装配时为避免挤压和切割受伤，必须戴上手套。
本产品只允许作为洗浴、卫生和洁身之用。
不得让儿童和肢体、精神和⁄或意识有障碍的成人
在不受监管的情况下使用淋浴系统。受酒精或毒
品影响的人员不得使用淋浴系统。
冷热水管间过大的压力差必须予以平衡。
安装提示
⁄ 安装前必须检查产品是否受到运输损害。 安装后
将不认可运输损害或表面损伤。
⁄ 管道和阀门必须根据通用标准进行安装、冲洗和
检查。
⁄ 请遵守当地国家现行的安装规定。
⁄ 该产品不可与液控和热控即热式热水器连接使
用。
技术参数
工作压强： 最大 1 MPa
推荐工作压强： 0,1 - 0,5 MPa
测试压强： 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
热水温度： 最大 60°C
热力消毒: 70°C ⁄ 4 分钟
⁄ 自动防止回流
⁄ 该产品专为饮用水设计！
符号说明
请勿使用含有乙酸的硅胶！
调节(参见第页 08)
安装完成后必须检查调温器的出水温度。如
在取水处测量所得的温度与调温器上设定的
温度有偏差，那么必须进行调整。
安全功能(参见第页 08)
恒温阀芯的安全功能可以预先设定所希望的
最高出水温度，例如最高温度为42℃
保养(参见第页 10)
⁄ 单向阀必须在符合国家或当地的法律的情
况下按照EN 806-5定期检查 (至少一年一
次) 。
⁄ 为了保证恒温器的稳定运转，请务必定期
从最热到最冷转动调温器。
大小(参见第页 17)
流量示意图(参见第页 17)
时的流速
清洗(参见第页 12)
备用零件(参见第页 14)
选装附件(参见第页 16)
不在供货范围内
⁄ 加长 25 mm #13595000
⁄ 加长件22mm (墙壁不够深时) #98860000,
#97407000, 13596000
⁄ 加长件33mm (墙壁不够深时) #14971000,
#14964000, 14960000
操作(参见第页 17)
+

03 ZH
安装(参见第页 06)
问题 原因 补救
⁄龙头出水量小 ⁄ 水压不足 ⁄ 检查总水压
⁄ 调压器过滤网脏污 ⁄ 清洁龙头前面和恒温阀芯的过滤
网。 ( 参见第页 10)
⁄ 花洒滤网有垃圾堵塞
⁄ 花洒过滤器元件有垃圾堵塞
⁄ 清洗花洒和软管间的过滤网
⁄ 清洗花洒和软管间的过滤密封件
⁄串水，在龙头关闭的状态下，热水
被强迫流入冷水管路，或者相反。 ⁄ 单向阀有垃圾堵塞或漏水 ⁄ 清洗单向阀，如有必要则更换新的
⁄龙头出水温度和温度设定的不符 ⁄ 恒温阀芯未被调节 ⁄ 调节恒温器
⁄ 热水温度过低 ⁄ 将热水温度从42ºC升高到60ºC
⁄水温无法调节 ⁄ 恒温阀芯表面结垢 ⁄ 更换-恒温阀芯
⁄ 对于新的安装：基体连接不正确 (
可能是：右冷，左热) 或者安装时
旋转180º
⁄ 安装功能块时，旋转180º
⁄安全停止按钮不工作 ⁄ 弹簧损坏
⁄ 按钮僵化
⁄ 清洁弹簧和⁄或按钮，并视需要更换

04
EN
SAFETY NOTES
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The product may only be used for bathing, hygienic
and body cleaning purposes.
Children as well as adults with physical, mental and ⁄or
sensoric impairments must not use this product without
proper supervision. Persons under the influence of
alcohol or drugs are prohibited from using this product.
The hot and cold supplies must be of equal pressures.
INSTALLATION INSTRUCTIONS
⁄ Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
⁄ The pipes and the fixture must be installed, flushed and
tested as per the applicable standards.
⁄ The plumbing codes applicable in the respective
countries must be observed.
⁄ This mixer cannot be used in conjunction with
hydraulically, electronically or thermally controlled
instantaneous heaters.
TECHNICAL DATA
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Thermal disinfection: 70°C ⁄ 4 min
⁄ Safety against backflow
⁄ The product is exclusively designed for drinking water!
SYMBOL DESCRIPTION
Do not use silicone containing acetic acid!
ADJUSTMENT (see page 08)
After the installation, the output temperature of
the thermostat must be checked. A correction is
necessary if the temperature measured at the
output differs from the temperature set on the
thermostat.
SAFETY FUNCTION (see page 08)
The desired maximum temperature for example
max. 42º C can be pre-set thanks to the safety
function.
MAINTENANCE (see page 10)
⁄ The check valves must be checked regularly
according to EN 806-5 in accordance with
national or regional regulations (at least once
a year).
⁄ To guarantee the smooth running of the
thermostat, it is necessary from time to time to
turn the thermostat from total hot to total cold.
DIMENSIONS (see page 17)
FLOW DIAGRAM (see page 17)
free flow
CLEANING (see page 12)
SPARE PARTS (see page 14)
SPECIAL ACCESSORIES
(see page 16)
order as an extra
⁄ extension 25 mm #13595000
⁄ Extension Set 22 mm (when wall is not deep
enough) #98860000, #97407000,
13596000
⁄ Extension Set 33 mm (when wall is not deep
enough) #14971000, #14964000,
14960000
OPERATION (see page 17)
+

05 EN
ASSEMBLY (see page 06)
FAULT CAUSE REMEDY
⁄ Insufficient water ⁄ Supply pressure inadequate ⁄ Check water pressure (If a pump has
been installed check to see if the pump
is working).
⁄ Regulator filter dirty ⁄ Clean filter in front of the mixer and on
the MTC-thermo cartridge ( see page
10)
⁄ Shower filter seal dirty
⁄ filter insert shower dirty
⁄ Clean filter seal between shower and
hose
⁄ Clean filter insert between shower and
hose
⁄ Crossflow, hot water being forced into
cold water pipe, or vice versa, when
mixer is closed
⁄ Backflow preventers dirty or leaking ⁄ Clean backflow preventers, exchange
if necessary
⁄ Spout temperature does not
correspond with temperature set
⁄ Thermostat has not been adjusted ⁄ Adjust thermostat
⁄ Hot water temperature too low ⁄ Increase hot water temperature to
42 ºC to 60 ºC
⁄ Temperature regulation not possible ⁄ thermo cartridge calcified ⁄ Exchange thermo cartridge
⁄ For new installations: basic body incor-
rectly connected (should be: cold right,
hot left) or installed with 180º rotation
⁄ Install function block turned through
180º
⁄ Safety stop button not operating ⁄ Spring defective
⁄ Button calcified
⁄ Clean spring and⁄or button, exchange
if necessary

06
2.
1.
X
1 - 2 mm
SW 4 mm
(5 Nm)
SW 5 mm
X + 11
2.
3.
0180 0187
1.
2.
1 - 2 mm
Armaturenfett
Grease
䀵滑油
1.
2
5 6
43
1
Montage

07
(0,1 Nm)
3.
4.
SW 3 mm
(2 Nm)
SW 2 mm
(2 Nm)
1.
3.
4.
SW 3 mm
(2 Nm)
1.
2.
Armaturenfett
Grease
䀵滑油
Armaturenfett
Grease
䀵滑油
2.
7 8 9
10
11b
11a
Montage

08
1.
2.
2.
1.
3.
2.
SW 3 mm
SW 2 mm
SW 2 mm
SW 2 mm
(2 Nm)
1.
1 32
21
Justierung ⁄ Safety Function

09
2.
1.
SW 2 mm
(2 Nm)
1.
2.
z. B. 42° C
for example 42° C
2.
1.
3
5
4
6
8
7
Safety Function

10
SW 4 mm
2.
3.
SW 2 mm
1.
SW 24 mm
2
3 4
5 6
1
Wartung