aXtion slim User manual
Installation Guide Guide d'installation ご 利 用 ガ イド
Installation Guide Guide d'installation ご 利 用 ガ イド
Open enclosure
from the edge
1
2
Place water test paper
inside, face down to the
front of case/screen side.
Water test paper face down
3
Close enclosure.
Make sure the gap is
closed completely.
6
Water Test Passed
4
2lb.
12 in
30cm
12 in
30cm 10Min
Test under 12" of water for 10 minutes
5
Dry the outer case prior to opening and ensure the
water test pad is dry.
Cleaning Instructions for aXtion Bold
Instructions de nettoyage pour aXtion Bold
aXtion Bold の清掃手順
We recommend cleaning the case after every use cycle.
Most hospital-grade disinfectant wipes with high alcohol
concentrate are safe to use on the aXtion Bold case.
Nous recommandons de nettoyer l’étui après chaque cycle
d'utilisation. La plupart des lingettes désinfectantes de qualité
hospitalière contenant un alcool concentré sont sans danger pour une
utilisation sur l’étui aXtion Bold.
使用ごとにケースを清掃することをお勧めします。高アルコール濃縮物を
含むほとんどの病院グレードの消毒ワイプを、aXtionBoldケースで安全に
使用できます。
1. Remove the tablet from the case and set aside.
Retirez la tablette de l’étui et mettez-la de côté.
ケースからタブレットを取り出し、脇に置きます。
2. Clean the inside back cover with a hospital-grade wipe, using a small stroking
motion. Pay special attention to the crevices.
Nettoyez l’intérieur du couvercle arrière avec une lingette de qualité hospitalière en
effectuant un petit mouvement de va-et-vient. Faites particulièrement attention aux
crevasses.
病院グレードのワイプを使用して小さなストロークで、背面カバーの内側を拭きます。特に
隙間に注意してください。
3. Use a new hospital-grade wipe to clean the inside the screen protector and plastic
frame.
Utilisez une nouvelle lingette de qualité hospitalière pour nettoyer l’intérieur de la
protection d'écran et le cadre en plastique.
新しい病院グレードのワイプを使用して、画面プロテクターとプラスチック製カバーの内側
を清 掃します。
4. Let the case air dry before putting the tablet into the case.
Laissez l’étui sécher à l’air avant d’y remettre la tablette.
ケースにタブレットを入れる前に、ケースを空気乾燥させてください。
1. Clean the back cover with a hospital-grade wipe, using a small stroking motion. Pay
special attention to the crevices.
Nettoyez le couvercle arrière avec une lingette de qualité hospitalière en effectuant
un petit mouvement de va-et-vient. Faites particulièrement attention aux crevasses.
病院グレードのワイプを使用して小さなストロークで、背面カバーを拭きます。特に隙間に
注意してください。
2. Use a new hospital-grade wipe to clean the screen protector and plastic frame.
Utilisez une nouvelle lingette de qualité hospitalière pour nettoyer la protection
d'écran et le cadre en plastique.
新しい病院グレードのワイプを使用して、画面プロテクターとプラスチック製カバーを清掃
します。
3. Let the case air dry before using.
Laissez l’étui sécher à l’air avant utilisation.
使用する前にケースを空気乾燥させてください。
Internal cleaning may be done as needed following these steps
Un nettoyage interne peut être effectué si besoin en suivant ces
étapes.
必要に応じて、これらの手順に従って、内部清掃を実行してください。
* Hospital-grade disinfectant wipes may have more detailed instructions for use. Please
refer to the manufacturer’s instructions.
* These instructions are only for cleaning cases by The Joy Factory. To clean the tablet,
please refer to the manufacturer’s instructions.
* Les lingettes désinfectantes de qualité hospitalière peuvent comprendre des instructions
plus détaillées. Veuillez vous reporter aux instructions du fabricant.
* Ces instructions concernent uniquement le nettoyage des étuis The Joy Factory. Pour
nettoyer la tablette, veuillez vous reporter aux instructions du fabricant.
* 病院グレードの消毒ワイプには、より詳細な使用説明書が付属しれている場合があります。メー
カ−の指示を参照してください。
* これらの指示は、The Joy Factoryが製造するケースの清掃のみを対象としています。タ ブ レ ット
を清掃する場合は、メーカ−の指示を参照してください。
7
8
Close enclosure. Make sure the gap
is closed completely.
9
Type cover installation Select models only
support@thejoyfactory.comContact us
DISCLAIMER FOR aXtion™ Slim Military Grade and Waterproof Certified Cases
Congratulations on the purchase of your new aXtion Slim case from The Joy Factory Inc!
BEFORE USE READ ALL INSTRUCTIONS CAREFULLY. IMPROPER USE OF THE CASE COULD RESULT IN DAMAGE TO YOUR
DEVICE.
This aXtion Slim case is designed only for the device type listed on the box. Thus it is only intended for and only warrantied for
proper use with that specific tablet and not for use with another device type. Because different generations of tablets have
different specifications, please refer to the packaging for your aXtion Slim case to determine whether your tablet will be
compatible with the aXtion Slim case you have purchased.
If you are not certain whether the device you intend to use with the aXtion Slim case is compatible with the tablet model you have,
please contact the company from which you purchased the device or the manufacturer of the device to determine whether it is
a model supported by this aXtion Slim case.
All aXtion Slim cases are certified IP68 waterproof. If you have any questions about whether your case will protect against water
in certain situations, contact The Joy Factory prior to using the case in those situations. The IP68 rating means that the aXtion
Slim case is certified as “dust tight” (that is, no dust will enter the case when it is properly installed and used). All aXtion Slim
cases are also designed to be shock resistant. That is, these cases are designed to provide a degree of confidence that your
aXtion Slim case can physically and functionally withstand the relatively infrequent, non-repetitive shocks encountered in various
environments.
It is critical that before using your aXtion Slim case with your device, you first perform a waterproof test without your device in the
case. It is especially important to ensure the case is properly closed when exposing it to water. An improperly closed case will
render it non-waterproof and will damage the device. Do not use your aXtion Slim case with your device without first ensuring you
are readily familiar with your aXtion Slim case and how it functions.
If the aXtion Slim case is damaged or not functioning properly for any reason; immediately stop use. The Joy Factory expressly
disclaims all liability and all warranties, whether expressed or implied, for use of an aXtion Slim case that has been damaged for
any reason. The case is covered under our one year manufacturing warranty and can be replaced free of charge for any
manufacturing defects. If you believe the case has a manufacturing defect, cease use immediately and contact The Joy Factory
by email at support@thejoyfactory.com or by telephone at (949) 216-8888, Monday through Friday, 9:00 a.m. to 5:00 p.m., Pacific
Standard Time. The Joy Factory will not replace an aXtion Slim case that is damaged, other than one with a manufacturing
defect, The Joy Factory is not liable to replace or pay for replacement of your device or any additional items which may be
damaged from use of a case with manufacturing defects.
The Joy Factory disclaims all liability for lost aXtion Slim cases and any device stored in a lost case.
Do not use your aXtion Slim case with any other case or bumper. Use of an additional case or bumper will render the aXtion Slim
Case non-waterproof, and The Joy Factory disclaims all liability from such use and will void any and all warranties, expressed or
implied.
Any alteration to your aXtion Slim case will void any and all warranties and guarantees, whether expressed or implied, and The
Joy Factory disclaims any and all liability for damages arising from use of an altered aXtion Slim case.
Using the aXtion Slim case with any other device could lead to an improper seal of the case and will render the case
non-waterproof. The Joy Factory disclaims all liability and all warranties, whether expressed or implied, for use of the aXtion Slim
case with any other device.
Table of contents
Other aXtion Tablet Accessories manuals
