Axvue E632 User manual

Get to know us at: www.axvue.com
Please read the following instrucons and warnings carefully
Keep this instrucon manual for future.
For technical support see FAQ page.
For adult use only.
SETUP & USE
Adapters:
INSTRUCTION MANUAL
Model- E632
Revised at 9/2020
Asphyxiaon Danger: Store this product out of the reach of babies (at least 3 feet away from the
crib). A strap wound around baby’s neck may result in asphyxiaon. Use safety clip to clamp the power
cord and keep it out of baby’s reach. Do not use other extension cords. Only use the power adapter
provided.
- Only use the recommended rechargeable baery. Please contact with us if you need to change it.
For contact list, please refer to the last page of the instrucon.
- Please clean the baery compartment before using.
- Avoid short circuit at power supply terminal.
- Remove the baery when you are not using it or when running out of power.
- Keep baery away from children.
- Dispose the empty baery properly.
- Store this product out of the reach of babies (at least 3 feets (0.9 m) away from the crib). A strap
wound around baby’s neck may result in asphyxiaon. Use safety clip to clamp the power cord and
keep it out of baby’s reach. Do not use other extension cords. Only use the power adapter provided.
- Do not touch the exposed part if the adapter is connected with power.
- Test regularly before inial use or when change the posion of camera.
- Avoid placing the product in humid place or contacng with liquid. (such as bathtub, sink, etc.)
- Do not apply heat to the product.(such as stoves, radiators, etc.)
- Using the product in venlated place. Avoid placing it on sofas, cushions, beds or other places which
may block venlaon.
- The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION ON YOUR CHILD.
WARNING
WARNING
BATTERY WARNING
3 feet
Figure 1
3 feet
Figure 2
Please charge the battery for at least 8 hours
before using the product.
Step 1: Test recepon first, put camera in a suitable
place that will provide you the best view of your baby in
the crib (Note: Do not hang up the camera firmly unl
inial installaon test is completed). Plug adapter into
wall outlet and turn on the camera.
Step 2: Turn on monitor by pressing and holding Power /
Menu buon for 5 seconds unl “axvue” shows up,
then video will show up on the screen immediately. If
video does not show up, please refer to “TO PAIR
MONITOR AND CAMERA (ADD CAMERA)” at next page. If
video shows up, the inial installaon test is completed,
then you can set up the camera according to the
instrucon below.
Set Up Camera: Place camera on a flat surface, such as
wardrobe or shelf (Figure 1). Or hang it on the wall
(Figure 2). No maer wherever to place the camera,
please make sure to keep it away from the crib for at least
3 feet and all power cords should be placed behind the
camera properly. Then adjust the angle of camera lens
unl the enre crib shows up on the display, or adjust it
to the best angle that you think to watch your baby.
FEATURES & COMPONENTS
Camera:
AXVUE E632 Video Baby Monitor
with 5.0'' LCD Screen and Two Cameras
TO USE PORTABLE / BATTERY MODE
Step 1: Charge the baery for at least 8 hours before using portable / baery mode.
Step 2: Make sure the adapter is plugged into camera.
Step 3: The baery life can be up to 10 hours if it is fully charged.
Baery life will be shortened if recharging it connuously. Unplug the power adapter when you are
not using it for a long me.
Please charge the baery for 6~8 hours before using the product.
TO USE PLUGGED-IN MODE
Step 1: Place the monitor display in living room, bedroom or any place you want to watch your baby.
Use adapter to connect camera with electrical outlet.
Step 2: Turn on monitor by pressing POWER/MENU buon for 5 seconds unl axvue logo or video
shows up on the screen.
Step 3: Press VIDEO ON/OFF buon to turn off the video if you only need to hear the voice.
Step 4: Turn off the monitor completely by pressing and holding POWER/MENU buon for
5 seconds.
The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer
to the following steps:
TO PAIR MONITOR AND CAMERA (ADD CAMERA)
Step 1: Make sure the camera and monitor are in the same place.
No
Signal
Step 2:
Step 3:
Turn on monitor by pressing
and holding POWER/MENU
buon for 5 seconds.
1. LED*
2. Power / Menu
3. OK / Confirm
4. Zoom
5. Talk Back
6. Video On / Off
7. Up / Volume Up
8. Down / Volume Down
9. Le / Brightness High
10. Right / Brightness Low
11. Microphone
12. Speaker
13. Baery Compartment
14. DC Jack
15. Kickstand
× 3× 1
Monitor:
Power & Low Baery Sound Lights
*LED
1. Lens
2.
Nighme LEDs
3. Microphone
4. Power On / Off Switch
5. Speaker
6. Temperature Sensor
7. DC Jack
8. Wall mounng hole
× 2
5
Make sure the AC adapter is plugged into
camera and turn on the camera by
pressing Power On / Off Switch “ ”
buon for 5 seconds.

cam 1 80°F cam 1 27°C
SETUP & USE (connued)
FCC INFORMATION
This device complies with part 15 of FCC Rules. Operaon is subject to the following
two condions: (1) The device may not cause harmful interference, and (2) This
device must accept any interference received, including interference that may
cause undesired operaon.
CAUTION
Changes and modificaons not expressly approved by AXVUE may void the users
authority to operate this equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B
digital device,
Pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protecon against harmful interference in a residenal installaon. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instrucons, may cause harmful interference to radio
communicaons. However, there is no guarantee that interference will not occur in a
parcular installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
CAUTION
1. To comply with the FCC RF exposure compliance requirement, a separaon
distance of 20 cm must be maintained between the antenna of this device and all
persons.
2. This transmier most not be co-located or operang in conjuncon with any other
antenna or transmier.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY INSTRUCTIONS
• Make sure you read this instrucon carefully before using the product.
• Store this instrucon safely for your future reference.
• Ensure that you read the “Warning” secon of the product package and this instrucon carefully.
• Use the product properly by following this instrucon.
• Wipe the product by wet towel aer you take it down from the wall.
• Avoid possible danger by following manufacturer’s instrucon.
• Do not using the product in humid place or contact with liquid, like bathtub, hand washing sink, kitchen sink, laundry tub,
humid basement, swimming pool, etc.
• Ensure the product is installed in a flat place. Otherwise, it will cause serious personal injury and product damage when
dropped.
• Only follow this instrucon and use installaon tools provided by the manufacturer to set up the product.
• The slots and holes on the product are used for venlaon, please ensure that it is not covered or blocked by other objects.
• Do not place the product on bed, sofa, rug or other similar places, it will block or cover the slots and holes on the product.
Do not place the product in a closed bookcase or shelf unless it has parcular part for venlaon.
• This product should be connected with certain power supply unit, if you are not sure about the power supply system in your
home, please contact with your product dealer and local power supply company. Please refer to the operang instrucon if
you want to operate the product in portable/baery mode or by connecng with other power supply sources.
• Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against
them, paying parcular aenon to cords at plugs, convenience receptacles, and the point where they exit from the product.
• An outside antenna system should not be located in the vicinity of overhead power lines or other electrical lines or power
circuits, it will cause interference for the signal transmission. When installing an outside antenna system, extremely aenon
should be paid to avoid touching such power lines or circuits, otherwise, you will have possible danger of electrical shock.
• Do not overload wall outlet, extension cords or convenience receptacles, this can be cause a risk of fire or electrical shock.
• Do not insert any ny objects into the product’s inside, it may touch dangerous voltage point or cause short-circuit, this can
be cause a risk of fire or electrical shock. Any kind of liquid spillage happens on the product should be avoid.
• Do not maintain the product by yourself as opening and removing the covering, this may expose you to dangerous voltage
or other hazards. Please contact with qualified service personnel for maintaining.
• Unplug the product from wall outlet and contact with qualified service personnel if you have problems as below:
- When the power-supply cord or plug has been damaged.
- If liquid has been spilled, or objects have fallen into the product.
- If the product has been exposed to rain or water.
- If the product didn’t operate normally by following the operang instrucons, please only adjust those controls which are
covered by the operang instrucons. An improper adjustment of other controls may result in product damage,
it will also require extensive work from qualified service personnel to restore the product to its normal operaon mode.
- If the products has been dropped or damaged in any way, or when the product shows a disnct change in
performance - this indicated that the product need to be maintained.
• Replacement parts - When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or its have the same characteriscs as the original part. Unauthorized substuons may
result in fire, electrical shock or other hazards.
• Safety Check - Upon compleon of any service or repairs to this product, ask the service technician to run safety checks on
the product to confirm that it is in a proper operang condion.
• The product only can be mounted on the wall or ceiling as recommended by the manufacturer.
• The product should be kept away from heat sources, such as radiator, heat registers, stoves or other products (including
amplifier) which can produce heat.
The SCAN, SELECT, ADD, DELETE, VIEW CAMERA opons are only available when mulple
cameras connected with the monitor. Order extra cameras by vising us at
www.axvue.com or search “Axvue Baby monitor” on Amazon.
TO DELETE A CAMERA
Favorite Features
Press and hold the TALK
BACK buon on the
monitor to acvate two-way
communicaon mode.
* Press the Power / Menu buon again to stop scanning.
DIGITAL ZOOM IN & OUT
x 1 Zoom x 2
TWO-WAY COMMUNICATION
Step 4:
TO SELECT A CAMERA
TO ADJUST SCREEN COLOR TEMPERATURE
4
cam 1
3
OK
5
OK
1
2
TO SET UP VOX - VIDEO ON CRYING
cam 1
Press &
hold
Press & hold
for 5 seconds
TO SCAN ALL CAMERAS (AUTO-SCAN)
1
2
CAM SIGNAL WILL BE LOST!
CANCEL YES
732-0E63200-0701
AXVUE INC.
Revised at 09/2020
*Any updated or revised version please refer to axvue official website.
AXVUE stands behind all of its products.
If you are not completely sasfied or have any quesons,
please contact us at hps://www.axvue.com
Connect with us:
VIDEO
ON/OFF
°F °C
1
2
5
OK
7
OK
5
OK
4
3
OK
6
3
OK
Red LED flashs
1
cam 1 scan 2
3
OK
2
cam 1
No
Signal
4
cam 2
3
OK
5
OK
1
2
4
cam 1 vox 3
3
OK
5
OK
1
2
BRIGHTNESS ADJUSTMENTVOLUME CONTROL
TEMPERATURE DISPLAY
OFF 1 2 3
Press
cam 1
x 1
cam 1