Axvue E722 User manual
Get to know us at: www.axvue.com
Please read the following instrucons and warnings carefully
Keep this instrucon manual for future.
For technical support see FAQ page.
For adult use only.
Adapters:
INSTRUCTION MANUAL
Model- E722
Revised at 12/2020
AXVUE E722 Video Baby Monitor
with 2.8'' LCD Screen and Two Cameras
The SCAN, SELECT, ADD, DELETE, VIEW CAMERA opons are only available when mulple
cameras connected with the monitor. Order extra cameras by vising us at
www.axvue.com or search “Axvue Baby monitor” on Amazon.
1. LED*
2. Microphone
3. Power/Video
4. Talk Back/Zoom
5. Volume Up/Up
6. Menu/OK
7. Right
8. Volume Down/Down
9. Le
10. Speaker
11. Baery Compartment
12. DC Jack
13. Kickstand
× 3× 1 × 2
Power & Low Baery Sound Lights
*LED
Keep the distance between sensor
and body at least 0.6 inch for
accurate temperature result.
1. Night-Vision LED
2. Lens
3. Microphone
4. Speaker
5. Power/Code
6. Temperature Sensor
7. DC Jack
8. Wall Mounng Hole
0.6 in
Monitor:
TO USE PORTABLE/BATTERY MODE
Step 1: Charge the baery for at least 8 hours before using portable/baery mode.
Step 2: Make sure the adapter is plugged into camera.
Step 3: The baery life can be up to 10 hours if it is fully charged.
Baery life will be shortened if recharging it connuously. Unplug the power adapter when you are
not using it for a long me.
Please charge the baery for 6~8 hours before using the product.
TO USE PLUGGED-IN MODE
Step 1: Place the monitor display in living room, bedroom or any place you want to watch your baby.
Use adapter to connect camera with electrical outlet.
Step 2: Turn on monitor by pressing
Power/Video“ ”
buon for 6 seconds unl axvue logo or video
shows up on the screen.
Step 3: Press
Power/Video“ ”
buon to turn off the video if you only need to hear the voice.
Step 4: Turn off the monitor completely by pressing and holding
Power/Video“ ”
buon for
5 seconds.
The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer
to the following steps:
TO PAIR MONITOR AND CAMERA (ADD CAMERA)
Step 1: Make sure the camera and monitor are in the same place.
Step 2:
Step 3:
Make sure the power adapter is plugged into
camera and turn on the camera by pressing
Power/Code“ ” buon for 6 seconds.
Turn on monitor by pressing
and holding Power/Video
“ ” buon for 6 seconds.
６
Step 5:
Step 4:
Red LED flashs
vox
TEMP
CF
13 24
13 24
4
2
3
165
Press
Press
SETUP & USE
3 feet
Figure 1
3 feet
Figure 2
Please charge the battery for at least 8 hours before
using the product.
Step 1: Test recepon first, put the camera in a suitable place that
will provide you the best view of your baby in the crib (Note: Do
not hang up the camera firmly unl the inial installaon test is
completed). Plug the adapter into the wall outlet and turn on the
camera.
Step 2: Turn on the monitor by pressing and holding the Power/
Video
“ ”
buon for 6 seconds unl “axvue” shows up, then the
video will show up on the screen immediately. If the video does
not show up, please refer to “TO PAIR MONITOR AND CAMERA
(ADD CAMERA)” on the next page. If the video shows up, the
inial installaon test is completed, then you can set up the
camera according to the instrucon below.
Set Up Camera: Place the camera on a flat surface, such as a
wardrobe or shelf (Figure 1). Or hang it on the wall (Figure 2). No
maer wherever to place the camera, please make sure to keep it
away from the crib for at least 3 feet and all power cords should be
placed behind the camera properly. Then adjust the angle of the
camera lens unl the enre crib shows up on the display, or adjust
it to the best angle that you think to watch your baby.
-Store this product out of the reach of babies (at least 3 feets (0.9 m)
away from the crib). A strap wound around the baby’s neck may result in
asphyxiaon. Use a safety clip to clamp the power cord and keep it out
of baby’s reach. Do not use other extension cords. Only use the power
adapter provided.
-Do not touch the exposed part if the adapter is connected with power.
-Test regularly before inial use or when change the posion of camera.
-Avoid placing the product in humid place or contacng with liquid. (such as bathtub, sink, etc.)
-Do not apply heat to the product.(such as stoves, radiators, etc.)
-Using the product in venlated place. Avoid placing it on sofas, cushions, beds or other places which
may block venlaon.
-The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION
ON YOUR CHILD.
WARNING
-Only use the recommended rechargeable baery. Please contact us if you need to change it.
For the contact list, please refer to the last page of the instrucon.
-Please clean the baery compartment before using it.
-Avoid short circuits the power supply terminal.
-Remove the baery when you are not using it or when running out of power.
-Keep the baery away from children.
-Dispose of the empty baery properly.
BATTERY WARNING
FEATURES & COMPONENTS
Camera:
６
12
6
SETUP & USE (connued)
Favorite Features
Press and hold the Talk
Back/Zoom“ ” buon on
the monitor to acvate
two-way communicaon
DIGITAL ZOOM IN & OUT
x 1 x 1Zoom x 2
TWO-WAY COMMUNICATION
BRIGHTNESS
ADJUSTMENT
VOLUME
CONTROL
TEMPERATURE DISPLAY
cam 1 85°F cam 1 85°Fcam 1 85°F
vox
TEMP
CF
51
2
43
cam 1 29°C
cam 1 85°F
1
Press &
hold
cam 1 85°F
TO DELETE A CAMERA
3
1
2
vox
TEMP
CF
5
4
CAM SIGNAL WILL BE LOST!
CANCEL YES
87
TO SELECT A CAMERA
12
cam 1 85°F
3
1
2
5
* Press the AUTO-SCAN“ ”
buon again to stop scanning.
TO SCAN ALL CAMERAS (AUTO-SCAN)
cam 1 85°F
31
2
TO SET UP VOX - VIDEO ON CRYING
cam 1 85°F
vox
TEMP
CF
3
1
2
TO ADJUST SCREEN COLOR TEMPERATURE
2
vox
TEMP
CF
5
43 6
71
6
cam 1 VOX 1 85°F
OFF 1 2 3
8
FCC INFORMATION
This device complies with part 15 of FCC Rules. Operaon is subject to
the following two condions: (1) The device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operaon.
CAUTION
Changes and modificaons not expressly approved by AXVUE may void
the users authority to operate this equipment.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device,
Pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protecon against harmful interference in a residenal
installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a
parcular installaon. If this equipment does cause harmful interference
to radio or television recepon, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
CAUTION
1. To comply with the FCC RF exposure compliance requirement, a
separaon distance of 20 cm must be maintained between the antenna
of this device and all persons.
2. This transmier most not be co-located or operang in conjuncon
with any other antenna or transmier.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
• Make sure you read this instrucon carefully before using the product.
• Store this instrucon safely for your future reference.
• Ensure that you read the “Warning” secon of the product package and this instrucon carefully.
• Use the product properly by following this instrucon.
• Wipe the product by wet towel aer you take it down from the wall.
• Avoid possible danger by following manufacturer’s instrucon.
• Do not using the product in humid place or contact with liquid, like bathtub, hand washing sink, kitchen sink, laundry tub, humid
basement, swimming pool, etc.
• Ensure the product is installed in a flat place. Otherwise, it will cause serious personal injury and product damage when dropped.
• Only follow this instrucon and use installaon tools provided by the manufacturer to set up the product.
• The slots and holes on the product are used for venlaon, please ensure that it is not covered or blocked by other objects.
• Do not place the product on bed, sofa, rug or other similar places, it will block or cover the slots and holes on the product. Do not
place the product in a closed bookcase or shelf unless it has parcular part for venlaon.
• This product should be connected with certain power supply unit, if you are not sure about the power supply system in your home,
please contact with your product dealer and local power supply company. Please refer to the operang instrucon if you want to
operate the product in portable/baery mode or by connecng with other power supply sources.
• Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them,
paying parcular aenon to cords at plugs, convenience receptacles, and the point where they exit from the product.
• An outside antenna system should not be located in the vicinity of overhead power lines or other electrical lines or power circuits, it will
cause interference for the signal transmission. When installing an outside antenna system, extremely aenon should be paid to avoid
touching such power lines or circuits, otherwise, you will have possible danger of electrical shock.
• Do not overload wall outlet, extension cords or convenience receptacles, this can be cause a risk of fire or electrical shock.
• Do not insert any ny objects into the product’s inside, it may touch dangerous voltage point or cause short-circuit, this can be cause
a risk of fire or electrical shock. Any kind of liquid spillage happens on the product should be avoid.
• Do not maintain the product by yourself as opening and removing the covering, this may expose you to dangerous voltage or other
hazards. Please contact with qualified service personnel for maintaining.
• Unplug the product from wall outlet and contact with qualified service personnel if you have problems as below:
- When the power-supply cord or plug has been damaged.
- If liquid has been spilled, or objects have fallen into the product.
- If the product has been exposed to rain or water.
- If the product didn’t operate normally by following the operang instrucons, please only adjust those controls which are covered by
the operang instrucons. An improper adjustment of other controls may result in product damage, it will also require extensive
work from qualified service personnel to restore the product to its normal operaon mode.
- If the products has been dropped or damaged in any way, or when the product shows a disnct change in performance
- this indicated that the product need to be maintained.
• Replacement parts - When replacement parts are required, be sure the service technician has used replacement parts specified by
the manufacturer or its have the same characteriscs as the original part. Unauthorized substuons may result in fire, electrical
shock or other hazards.
• Safety Check - Upon compleon of any service or repairs to this product, ask the service technician to run safety checks on the
product to confirm that it is in a proper operang condion.
• The product only can be mounted on the wall or ceiling as recommended by the manufacturer.
• The product should be kept away from heat sources, such as radiator, heat registers, stoves or other products (including amplifier)
which can produce heat.
AXVUE INC.
Revised at 12/2020
*Any updated or revised version please refer to axvue official website.
AXVUE stands behind all of its products.
If you are not completely sasfied or have any quesons,
please contact us at hps://www.axvue.com
IMPORTANT SAFETY INSTRUCTIONS
Connect with us:
732-E72200-0700
7
4
Other Axvue Baby Monitor manuals
