Azoteq IQ Switch ProxSense IQS231EV02 User manual

IQ Switch®
ProxSense®Series
Copyright © Azoteq (Pty) Ltd 2015.
IQS231EV02 Quick start guide
Page 1 of 3
All Rights Reserved.
Revision 1.0
August 2015
IQS231EV02 Quick start guide
Single Channel Capacitive Proximity/Touch/SAR Controller with movement detection
The IQS231ProxSense®IC is a self-capacitance controller designed for SAR applications
where a reliable proximity detection function is required along with human and inanimate
object distinction. The IQS231 uses quick release and movement detection to achieve this.
The IQS231 operates standalone or I2C can be configured via OTP (One Time
Programmable) bits.
1 Reference design and pin layout
Figure 1.1 IQS231EV02 Figure 1.2 TSOT23-6 Pin layout
Table 1.1 Multifunction pin descriptions
IQS231 in TSOT23-6
Pin
Name
Type
Function
1
PRIMARY I/O
Digital Input/Output
Multifunction IO1 / SCL (I2C Clock signal)
2
VSS
Signal GND
3
SECONDARY
I/O / Tx
Digital Input/Output
Multifunction IO2 / SDA (I2C Data output)
/ Tx
4
VREG
Regulator output
Requires external capacitor
5
VDDHI
Supply Input
Supply:1.75V –3.6V
6
Cx
Sense electrode
Connect to conductive area intended for
sensor
Table 1.2 Pin-out description
Multifunction pin name
Multifunction pin option
IO1
Proximity output / Proximity output with heartbeat
IO2
Sensitivity input / Synchronization input /
Movement output / Touch output
IQS
231
IO1 / SCL
VSS
IO2 / SDA / Tx
Cx / Rx
VDDHI
VREG
1
2
3
6
5
4

IQ Switch®
ProxSense®Series
Copyright © Azoteq (Pty) Ltd 2015.
IQS231EV02 Quick start guide
Page 2 of 3
All Rights Reserved.
Revision 1.0
August 2015
Figure 1.3 Reference design
2 Default UI
Figure 2.1 Proximity UI no movement
GND
C1
1uF
GND
C2
100pF
C4
100pF
C3
1uF
GND
VDDHI
GND
CX
VIN
VDDHI
GND
R1
470R
GND
VDDHI
Configure these resistors for IQS231 I2C operation.
PIN3: IQS231 SDA Pull-up PIN1: IQS231 SCL Pull-up
R2
4.7K
R3
4.7K
VDDHI
SEC/SDA
GND
IO1/SCL
IO2/SDA/TX
Optional: LED and current limiting resistor
PIN1: Output LED and current limiting resistor
on primary output
VDDHI
R4
1.0K
DS1
BLUE
PRIM/SCL
IO1/SCL IO1/SCL
IO1/SCL
IO2/SDA/TX
IO2/SDA/TX
C5
10pF
GND
LK1
2W-SLink Open
IO2/SDA/TX
3
IO1/SCL
1
VREG
4
CX/RX
6
VSS
2
VDDHI
5
U1
IQS231
Option: Sensitivity input
GND for more sensitivity
POR
Hand held detect
Proximity Active
Quick release
active &
Proximity Active
Filter halt
Idle
Prox clear
Redo ATI
Prox active
ATI error
Prox active
HH
Proximity Active
QR detect
Prox detect
5sec !Mov
2sec !Mov
Normal
prox
release
5sec
no prox
HH detect
enabled
Reference (LTA)
out-of-bounds
POR auto-ATI
calibration
complete
No calibration
convergence
10 sec
time-out
Mov
detect
5sec
!Mov
Disable HH
detect

IQ Switch®
ProxSense®Series
Copyright © Azoteq (Pty) Ltd 2015.
IQS231EV02 Quick start guide
Page 3 of 3
All Rights Reserved.
Revision 1.0
August 2015
Figure 2.2 IQS231 GUI
Different UI’s can be selected in the IQS231 GUI and can then be selected to run in
standalone mode.
The GUI is available for download from the Software & Tools section of azoteq.com and the
CT210 (sold separately) is used in conjunction with the GUI to select the different UI’s and
settings.
Using USBProg the IQS231 can be configured in different variations. Please note when
settings are programmed it is permanent.

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for Touch Sensor Development Tools category:
Click to view products by Azoteq manufacturer:
Other Similar products are found below :
TSC2100EVM TSC2003EVM-PDK ATMXT1066T2-DEV-PCB ATMXT336UDEVPCB LC717A00ARGEVK ATMXT641TDAT-I2C-PCB
MAX20353EVSYS# 1374 MIKROE-1906 1602 SEN0164 1982 STEVAL-PCC009V3 ATSAMD20-QTRDEMO ATQT2-XPRO ATQT6-
XPRO 2340 DM160221 DM160229 DM160222 ATQT5-XPRO DFR0129 SEN0170 SLEXP8019A SLEXP8018A 1375 SEN0186
SEN0148 DK-000013-03 ROB0103 cs-useful-01 DFR0385 SEN0184 SX8651EVKA 1362 2024 3575 4830 AS8579-TS_EK_DB
ATQT600 IQS227/228ASEV01 SKU-6515 CY3280-MBR2 CY3280-MBR3 DFR0030 DM160219 AC160219 AC320007 AC47H23A
ATEVK-MXT1066T2-A