Aztech Kyla User manual

User Guide

01
Thanks for using Aztech Kyla product
If you need support or help, please visit www.kyla.aztech.com
Smart Combustible
Gas Sensor

02
Reset
Button
Testing
Button
Status
Indicator
Gas Convection
Holes
Product Description
LED States
a. Solid Green Light with No Alarm Sound: Power On
b. Red Flashing Quickly w/ Sound: Alarm On
c. Solid Yellow Light w/ Long Buzzing: Malfunction
The Smart Combustible Gas
Sensor is used for detecting
combustible gas leakage,
preventing any possible
danger.
The sensor adopts extra
low-power consumption
Zigbee wireless module.

03
CEILING
FLOOR
Max
Diameter
3m
0.3m - 1.0m
Gas Stove
Sensor
0.3m - 1.0m
Installation Tips
Note: Before installation, please confirm the detecting
gas density - if heavier or lighter than air. If detected gas
is heavier than air (LPG, etc.), install at 0.3-1m height from
the floor. If detected gas is lighter than air (natural gas,
manufactured gas, marsh gas, etc.), install at 0.3-1m height
from ceiling, semi-diameter to gas source less than 1.5m.

04
Operation Guide
Step 1:
Download Aztech Kyla App from Google Play/App Store
Aztech Kyla App
Step 2:
Login to Aztech Kyla App, then add “Smart Combustible
Gas Sensor” to device list to enable the device.

05
Insert the Smart Combustible Gas Sensor into power
socket and enter Ad Hoc network condition. App will be
prompted once succesfully connected to the network.
Step 3:
3.1 Ad-Hoc Network

06
b.) Once the detector is on, the power indicator will show
green and the buzzer will beep once, signalling that the
device is on warm-up state. Then, will be followed by red
LED and yellow LED alternately flashing. Flashing will stop
after 3 mins when detector has entered normal working
status. Please do not test gas when detector is warming up.

07
After warming up, keep pressing the reset key for 2 sec
until green LED flashes quickly. App will be prompted
once connected succesfully. Green indicator will turn off
after 3 sec and will start lighting normally once detector
has entered normal working status.
Step 3:
3.2 Manual Network

08
Technical Specications
Product Dimensions: 79 x 68 x 31mm
Alarm Sound: 75dB/m
Alarm Sensitivity: 6% LEL ± 3% LEL
Networking: Zigbee Ad-hoc
Operating Temperature: -10~50°C
Working Humidity: Max 95% RH
Wireless Networking Distance: ≤ 100m (Open Area)

09
Notes
1. Shell surface will be slightly hot on normal working
conditions.
2. Please dismantle detector while decorating house.
3. Avoid spraying aerosol around sensor.
4. Oil adhesion on gas convection window may affect the
sensitivity of gas detector after prolonged usage. Cleaning the
gas convection window every 3 months (or based on specific
oil pollution level) with a brush mixed with a little amount of
detergent is recommended. Don’t let detergent enter the
detector’s body. Please re-test after cleaning.
5. Semi-conductor of the gas detector has a 5-year lifespan.
Please replace detectors timely.
6. Please do not use lighter to test the detector to avoid
damage to the gas sensor.
7. For your safety, in addition to using the detector properly,
please be vigilant and enhance safety precautions in your
daily life.

10
Emergency Alarm Response
The detector will keep alarming while the natural gas level or
LPG density in air has exceeded the normal range.
Please do the following after:
1. Shut down the tube valve right away.
2. Extinguish all fire sources and do not use anything that is a
fire hazard (e.g lighters, matches, etc.).
3. Avoid using switches on various electric equipment.
4. Open the window to make the air flow rapidly.
Troubleshooting
Symptom Reason Remedy
Always warming up
after power on
(LED keeps flashing)
Yellow LED is on
and buzzer keeps
on beeping
1. No usage in a long time
2. Testing gas detector when
warming up
Gas sensor fault
Contact dealer
for repair
1. Turn on detector and
aging test for 24 hours
2. Do not test detectors
when warming up

©2018 Aztech Technologies Pte Ltd. All rights reserved.