B-K lighting AGI2 User manual

RELEASE DATE
12-19-2019
REFERENCE NUMBER
INS-2816-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
1/8”, 3/16” & 0.050” Allen Wrench
Waterproof Wire Connectors
Phillips Screwdriver
Warning High Voltage Hot Surface
NEEDED
FOR
INSTALLATION:
By Others
Hydrolock Plate
(factory wired to
conduit assembly,
arrives installed in
CO2 Housing)
O-Ring
CO2
Housing
Heavy Wall
Composite
Housing
Faceplate
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
AGI2 LED
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
AGI2 Solid State Fixture
Driver Assembly
Plate With Quick
Connects
1” Notch
Direct Burial
Flexible
Conduit with
(3) 12Ga.,
THHN Wire
Mounting
Collar
Optic
Heat
Sink and
OptiLock™
Assembly
LED
Assembly
and Optic
Holder
Conduit
Assembly
Faceplate
Heavy Wall
Composite
Housing
Waterproof Wire
Connectors
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use
a soft cloth or gloves. Oil from skin may cause damage.
SAVE THESE INSTRUCTIONS

RELEASE DATE
12-19-2019
REFERENCE NUMBER
INS-2816-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
1. Place composite housing in hole. Align
flexible conduit through 1” notch in bottom
of composite housing. Pull conduit to splice
location.
Installation
PROJECT:
TYPE:
AGI2 LED
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Soil Prep
Conduit
Trench
Excavated
for Housing
C. Prep soil according to DIG-IT Guide.
Conduit
trench 18”
Dia.
A. Determine Soil Type by referencing DIG-IT
Guide.
B. Dig hole 18” wide and deep enough for
faceplate height above grade as per lighting
plan.
2. Make watertight connections using provided
waterproof wire nuts. See wiring diagram.
Hydrolock
Plate
LINE
COM
GROUND
DIM +
DIM -
WIRING DIAGRAM 3. For soil installation, fill and tamp soil to the
appropriate height. Fixture is above grade
specified by lighting plan.
Aiming Adjustment
1. Remove faceplate using 1/8” Allen wrench. 2. To aim OptiLock® horizontally: lift OptiLock®
from resting position, and rotate to desired
angle. Set down on pins provided in housing.
OptiLock® is gravity held in place.
3. To aim OptiLock® vertically: loosen two (2)
1/4-20 screws using 3/16” Allen wrench. Tilt
swivel arm with LED and optic in desired aiming
direction. Tighten two (2) 1/4-20 screws with
3/16” Allen wrench to secure position.
e below grade portion
of the housing to be 18”

RELEASE DATE
12-19-2019
REFERENCE NUMBER
INS-2816-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
PROJECT:
TYPE:
AGI2 LED
Accessory Holder
1. Remove faceplate using 1/8” Allen wrench. 2. Accessory sits in ring that rests on optic. Loosen
the thumbscrew before lifting the accessory
holder to change accessory.
3. To change or add accessory, pinch retaining
ring to remove from accessory holder. Place
accessory in holder, with honeycomb baffle
furthest from LED. Pinch retaining ring and
slide into holder, then release. Retaining ring is
tension held in place.
Smooth side of accessory lens (if used) faces
LED.
5. Install faceplate using 1/8” Allen wrench and
hand-tighten the faceplate screws in a star
pattern to 30” lbs. min.
Do not use a power tool to install screws. Do
not exceed 40” lbs.
4. Remove any dirt or debris in O-ring groove near
top of housing. Place O-Ring inside of groove.
Failure to clean groove of debris will cause
fixture to fail and void product warranty.
6. Install faceplate using 1/8” Allen wrench and
hand-tighten the faceplate screws in a star
pattern to 30” lbs. min.
Do not use a power tool to install screws. Do
not exceed 40” lbs.
5. Remove any dirt or debris in O-ring groove near
top of housing. Place O-Ring inside of groove.
Failure to clean groove of debris will cause
fixture to fail and void product warranty.
4. Place accessory holder over optic, honeycomb
baffle (If Used) furthest from LED. Retaining ring
is closest to LED. Place it back in place then tight
the thumbscrew for the accessory to be held in
place.

RELEASE DATE
12-19-2019
REFERENCE NUMBER
INS-2816-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
AGI2 LED
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Relamping and Optic Adjustment
10. Install faceplate using 1/8” Allen wrench and
hand-tighten the faceplate screws in a star
pattern to 30” lbs. min.
Do not use a power tool to install screws. Do
not exceed 40” lbs.
9. Remove any dirt or debris in O-ring groove near
top of housing. Place O-Ring inside of groove.
Failure to clean groove of debris will cause
fixture to fail and void product warranty.
1. Remove faceplate using 1/8” Allen wrench.
7. To aim OptiLock® horizontally: lift OptiLock®
from resting position, and rotate to desired
angle. Set down on pins provided in housing.
OptiLock® is gravity held in place.
8. To aim OptiLock® vertically: loosen two (2)
1/4-20 screws using 3/16” Allen wrench. Tilt
swivel arm with LED and optic in desired aiming
direction. Tighten two (2) 1/4-20 screws with
3/16” Allen wrench to secure position.
2. Turn, then lift OptiLock® from housing.
Disconnect OptiLock® assembly from driver
assembly using quick disconnect.
3. Remove optic by turning to the left and lifting
up. Remove the optic holder from the LED
board by loosening three (3) optic holder
fasteners using 0.050” Allen wrench.
6. Attach OptiLock® assembly to installed
driver assembly with quick disconnect. Place
OptiLock® assembly in housing, resting the
OptiLock® on the pins provided inside the
housing. Gravity will hold OptiLock® in place.
4. Use 0.050” Allen wrench to loosen three (3) #2-56
screws on LED component. Reverse install new
LED component. Ensure LED component is firmly
seated on heatsink. LED component can only fit
in one direction.
5. Install optic holder with three (3) optic holder
fasteners using 0.050” Allen wrench. Reverse
install optic.

Warning Hot Surface
TOOLS
NEEDED:
By Others
AGI2 LED
LED Installation
1/8”, 3/16” & 0.050” Allen Wrench
Phillips Screwdriver
Small Pick Tool
RELEASED
12-19-2019
REFERENCE NUMBER
INS-2816-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
1. Remove faceplate using 1/8” Allen wrench. Remove
optional accessory holder (if applicable).
2. Turn, then lift OptiLock® from housing. Disconnect
OptiLock® assembly from driver assembly using
quick disconnect.
9. Attach OptiLock® assembly to installed driver
assembly with quick disconnect. Place OptiLock®
assembly in housing, resting the OptiLock® on the
pins provided inside the housing. Gravity will hold
OptiLock® in place.
3. Remove optic by turning to the left to unlock optic
from optic holder tabs, and lift up.
Do not pull on connector or wiring. Handle with
care.
4. Use small Phillips screwdriver to remove two (2)
#4-40 fasteners on optic holder, then remove optic
holder to expose LED module.
5. Carefully remove LED module from heatsink.
Do not pull on connector or wiring. Handle with
care.
6. Use small pick tool to push connector off LED board
through two small slots behind connector. Once
loose, lift connector upwards and off board.
8. Reverse install optic holder, and then optic.7. Place new LED module onto heatsink. Press
connector straight downwards into slot on module
to snap into place.
Connector will only fit in one direction.