Baby Lock Endurance II BND9-2 Installation and operating instructions

1
ENGLISH
Before using the machine, carefully read both this manual and the Instruction and Reference
Guide included with your machine.
Contents
Pattern Type Selection Screen ....................................................................................................2
Additional keys .......................................................................................................................2
Checking the Needle Drop Point with LED Pointer ....................................................................2
Turning the LED pointer “ON” or “OFF”.................................................................................3
Various Types of Embroidery Frame Selections ..........................................................................3
Embroidery frame holders .......................................................................................................3
When It Is Difficult to Reach the Embroidery Frame..................................................................4
Changing the Embroidery Position Using Various Speed Keys....................................................4
Moving the Needle on the Error Message Screen .......................................................................5
Information about Appliqué Display ..........................................................................................5
Indicating when the machine stops .........................................................................................5
A specific needle bar number for appliqué..............................................................................5
Adjusting the Brightness of the Screen Display...........................................................................6
Cancelling the Thread Color Settings for All Previously Stitched Designs ..................................7
Moving Five Hundred Stitches Forward/Back.............................................................................8
Editing Patterns as a Group ........................................................................................................8
Sewing the repeated pattern without sorting colors .....................................................................9
Sending Embroidery Patterns From a Computer to the Machine (Link Function) .....................10
Operations available with the Link function..........................................................................10
Embroidering using the Link function....................................................................................11
Disabling the Link function ...................................................................................................14
Error messages in the Link function .......................................................................................15
Selecting the Thread Color Information for “PES” Format Data...............................................15
Checking the Length of Time until the Machine’s Next Stop ....................................................16
Checking the Temporary Needle Bar Setting............................................................................16
Cancelling the Temporary Needle Bar Setting .......................................................................17
New Character Patterns ...........................................................................................................18

2
Pattern Type Selection Screen
The pattern type selection screen slightly differs
from the screens listed in the Instruction and
Reference Guide. For details on the patterns
displayed when each key is pressed, refer to the
Quick Reference Guide.
Additional keys
Checking the Needle Drop Point with LED Pointer
The LED pointer shows you the location of the
needle penetration so that it is easier to adjust the
embroidery position.
1Needle drop point
The LED pointer turns on automatically while the
embroidering screen appears, and it turns off when
you start embroidering. You can set the LED pointer
function on or off in the settings screen.
Note
●The LED pointer may not be available
depending on the type of embroidery
frame attached.
●With fabric that has a very uneven or
textured surface, the position of the LED
pointer may not be correctly aligned. In
this case, the pointer indication should be
used only as a reference.
Press this key to select
one of the ten patterns
that were added.
Press this key to select
one of the patterns that
was available with
in the previous
version (excluding
).
Press this key to select
or , which were
available with in
the previous version.
provides patterns used
with examples in the
Instruction and Reference
Guide.
provides patterns used
for checking the thread
tension. For details on
checking the thread tension,
refer to page 67 in the
Instruction and Reference
Guide.

3
ENGLISH
Turning the LED pointer
“ON” or “OFF”
1Press .
2Display page 4 of the settings screen.
3Press to turn on the LED pointer to
check the needle drop point.
The key appears as when “ON” is
selected, and it appears as when
“OFF” is selected.
* Each touch of the key turns the setting either on or off.
Various Types of Embroidery Frame Selections
Various types of embroidery frames can be used with this machine to suit your project by changing the
embroidery frame holders.
Embroidery frame holders
Two types of embroidery frame holders
(embroidery frame holder A and embroidery frame
holder B) are included with this machine.
Embroidery frame holder A is used with the four
included embroidery frames. Embroidery frame
holder B is used with the optional embroidery
frames. In addition, if optional embroidery frame
holder C is used, a frame from the optional round
frame series can be installed. For details on which
embroidery frame can be installed on each
embroidery frame holder, refer to “Embroidery
frame types and applications” listed in the
Instruction and Reference Guide.
1Embroidery frame holder A
2White corner covers
3Embroidery frame holder B
4Light gray corner covers
5Magnet
6Embroidery frame holder C (optional)
7Dark gray corner covers

4
When It Is Difficult to Reach the Embroidery Frame
Depending on the position of the needle bars, it
may be difficult to reach the embroidery frame. In
that case, follow the procedure described below to
move the embroidery frame.
1Press .
XThe needle bar move screen appears.
2Press .
XThe carriage automatically moves to a
position where the embroidery frame can
easily be reached/removed.
• Touch to close the needle bar move
screen and to move the carriage to the
previous position.
Changing the Embroidery Position Using Various Speed Keys
The embroidery position can be moved using the
three variable speed keys.
1Move the position by 0.1mm
2Move the position by 0.5 mm
3Move the position at maximum speed.
Note
●Move the pattern in desired direction
using , after the speed is selected,
for maximum speed press and hold.
123

5
ENGLISH
Moving the Needle on the Error Message Screen
Press to move the needle backward or
forward to the position desired after correcting the
error.
Information about Appliqué Display
There is information about the appliqué display
which helps your operation.
Refer to “Appliqué Sewing” listed in the Instruction
and Reference Guide for the detailed instruction.
Indicating when the
machine stops
If an appliqué pattern was selected, appears in
the screen at places where the machine is stopped
to create appliqué.
A specific needle bar
number for appliqué
If an appliqué pattern was selected, "APPLIQUE
MATERIAL", "APPLIQUE POSITION" and
"APPLIQUE" are all assigned to a specific needle
bar number. Set the thread colors to be used for the
appliqué to that specific needle bar.

6
Adjusting the Brightness of the Screen Display
If the LCD screen is too dark or too light, you can
adjust the brightness of the screen display.
1Press .
2Display page 5 of the settings screen.
3Press or to adjust the brightness of
the screen display.
* The screen will appear dimmer if the number on the
settings screen decreases. The screen will appear
brighter as the number increases.

7
ENGLISH
Cancelling the Thread Color Settings for All Previously
Stitched Designs
Note
●The color settings will be completely
canceled even if the machine is in the
middle of the embroidery.
1Touch .
2Touch .
XThe thread color setting is canceled.
3Touch .
XThread colors are assigned by the machine
again, regardless of the previous spool
setting.
Note
●This function will not clear anchor settings
of any of the needles which have been
assigned a thread color (Refer to “Reserved
Needle Bar Settings” listed in the
Instruction and Reference Guide).

8
Moving Five Hundred Stitches Forward/Back
and have been added to the stitch
navigation screen. For details on moving forward or
backward through the stitching, refer to
“Embroidering From the Beginning or Middle of the
Pattern” listed in the Instruction and Reference
Guide.
Each touch of this key moves five hundred
stitches back through the stitching.
Each touch of this key moves five hundred
stitches forward through the stitching.
Editing Patterns as a Group
Combined patterns can be grouped and can all be
edited (rotated, resized, etc.) at the same time.
1Touch so that it changes to .
XAll patterns displayed in the pattern
display area are grouped.
* Touch to ungroup the patterns. If there are
multiple grouped patterns, the selected pattern group
is ungrouped.