Babyhug Tiny Tots Musical Baby Bouncer User manual

As Soothing As The Mother's Lap!
13.2 cm
19
cm
• Fall Hazard – It is dangerous to use this reclined bouncer on an elevated surface, since child's
movement may cause product to slide or tip over. Use only on floor.
• Suffocation Hazard – Never use it on a soft surface (bed, sofa or cushion), since product can tip over
and cause suffocation in soft surface.
• Always use the restraint system.
• Never leave child unattended when in use.
• Never use the toy bar as a handle
• Not recommended for children who can sit up by themselves
Warning
Style Code : BGBO001
baby bouncer
Vibrator Detachable Toy Bar
Carrying Capacity
11 Kg
Age Group
0 Months +
Care
• The pad is machine washable. Wash the pad separately in cold water on the gentle cycle.
Babyhug Laundry Detergent is recommended for best results.
• Do not use bleach
• Tumble dry separately on low heat and remove promptly.
• The frame and toy bar can be wiped clean using a mild solution and damp cloth.
• Do not immerse the soothing unit or toy bar.
Caution
• This package contains small parts in its unassembled state. Adlut assembly is required.
Imported For & Marketed By:
Brainbees Solutions Pvt Ltd
Corporate & Registered Office Address:
Rajashree Business Park, Plot No: 114,
Survey No. 338, Tadiwala Road,
Near Sohrab Hall, Pune 411 001
Customer Care :
020-30556310
[e-mail]
Operation Instructions
• Please read instructions carefully before assembling and using the product.
baby bouncer

5) Position the footrest so that the soothing unit is upright.
6) Fit the footrest on the end of the base wire.
1) Place the base tube on a flat surface.
2) Position the left and right base wires as shown.
3) Fit the left base wire and right base wire into the
base tube.
4) Position the base so that it faces towards you
and insert the right and left wire base into the
holes of the base tube.
Left
Base Wire
Right
Base Wire
Base Tube Base Tube
Left
Base Wire
Right
Base Wire
Footrest Footrest
Seat
Back Tube
Base Tube
Left
Base Wire
Right
Base Wire
Footrest
7) Position the seat back tube above the
base assembly.
8) Fit the seat back tube completely onto
the base wire.
9) Fix the base wire on corresponding side
of the seat back tube.
10) Repeat the procedure to secure the
other side of the seat back tube.
Base Tube
Seat
Back Tube
Seat
Back Tube
Base Tube
Footrest
12) Fit the pad upper pocket onto the seat back tube.
13) Fit the pad lower pocket onto the footrest.
14) Fit the toy bar ends into the sockets.
Set Up and Use
Securing your child
• If the toy bar is attached, remove it before placing your child on the seat.
• Now place the child on the seat and position the restraint pad between your child's legs.
• Fasten both restraint belts to the buckles on each side of the restraint pad. Make sure you hear “click”
on both sides.
• Attach the toy bar, if desired.
Calming Vibrations
• Make sure your child is properly secured on the seat.
• To turn the vibration on, slide the power switch to “on”.
• To turn vibration off, slide the power switch to “off”.
• Required one “D” (LR20) alkaline battery (not included) for operation.
Remove the Toy Bar
• Pull the end of the latches and lift the toy bar.
15) Make sure the toy bar latches are secure.
Base
Tube
Pad
Left & Right
Base Wire
Footrest
Right
Base Wire Left
Base Wire
Base Tube
Base Tube
Right
Base Wire
Left
Base Wire
Tiny Tots Musical Baby Bouncer - 8034T - BGBO001
11) Pull up the seat back tube, to be sure it is secure. If still you can remove either end of
the seat back tube, you have not assembled it correctly.
Pad
Left & Right
Base Wire
Footrest
Left & Right
Base Wire
Assembly
Before assembly and each use, inspect this
product for damaged hardware, loose
joints, missing parts, or sharp edges. DO
NOT use if any parts are missing or broken.