Babymore Aston Cot/Bed User manual

1|P a g e
INSTRUCTIONS
ASTON COT/BED
ASD: V1/15
Babymore Ltd Babymore
Babymore
Babymore
Babymore
Thank you for purchasing Babymore If you need assistance, spare parts or you are unhappy with the goods
Call: 020 3475 5588
or email: [e-mail]

2 | P a g e
IMPORTANT: READ CAREFULLY AND
RETAIN FOR FUTURE REFERENCE
INSTRUCTIONS FOR SAFE USE
The correct use and maintenance of your cot/bed will ensure it gives long and trouble-free use. Please ensure
everyone use your cot/bed know how to use it. The safety of your child is your responsibility.
•WARNING: Be aware of the risk of open fires and other sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the cot.
•WARNING: Do not use the cot/bed if any part is broken, torn or missing and use only spare parts approved
by Babymore.
•WARNING: Do not leave anything in the cot or place the cot close to another product which could provide a
foothold or present a danger of suffocaon or strangulaon, e.g. strings, blind/curtain cords, etc.
•WARNING: Do not use more than one maress in the cot.
•WARNING: When converted to a child’s bed, do not place this bed near heat sources, windows and other
furniture.
•The lowest base posion is the safest. Once your child is old enough to sit up unaided the base should be
used in the lowest posion only.
•If your leave the child unaended in the cot, always make sure that the movable side is closed
•The thickness of the maress chosen shall be such that the internal height (surface of the maress to the
upper edge of the cot frame) is at least 500mm in the lowest posion of the bed base and at least 200mm in
the highest posion of the bed base.
•The line engraved on the cot end indicates the maximum thickness of a maress that can be used with this
cot when the bed base is in the top posion.
•We recommend the use of a maress minimum size of 70cm by 140cm for this cot. With a thickness not
exceeding 10cm. The length and width of maress shall be such that the gap between the maress and the
sides and ends does not exceed 30mm.
•Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not be placed
too close to other furniture or windows, and should be placed either ght to any wall or have a gap of
300mm between the wall and the side of the bed.
•Please ensure that all assembly fings always be ghtened properly before use. And fings should be
checked regularly and ghtened as necessary.
•The cot is only ready for use, when the locking mechanism(s) are engaged, check the mechanism(s) is fully
engaged before use.
•Your cot/bed may be cleaned with a damp cloth. Never use bleach or harsh abrasives.
•To prevent injury from falls, once the child is able to climb out of the cot, the cot should no longer be used
for that child.
•This cot bed is intended for children aged from birth to 4 years approximately.
•The cot conforms to EN 716-1/2:2008 + A1:2013. When converted to bed, it conforms to BS 8509:2008 +
A1:2011.

3|P a g e
Improper assembly can result in damage to your furniture or cause harm to your child. Proper assembly is crical
to ensure a safe and comfortable end result. Please read all instrucons before assembly and keep for future use
BEFORE ASSEMBLY
Unpack all the parts and idenfy them against the components and fing lists.
Do not discard any packaging unl you are sure you have all the parts and fings.
If you find any part missing or damaged or incorrect, contact customer services of above.
Read the instrucons thoroughly before aempt construct the cot/bed.
You may find the construcon easier with help of another person, in the room for use, on a so clean
floor so there is no damage caused to the furniture during construcon.
Follow each stage of construcon step-by-step.
FITTINGS
Item Qty Item Qty
B
Item Qty
C
Item Qty
D
1
Item Descrip on Qty
E
2
Description
Dropside Bottom Pin
Description
Dropside Top Pin 2
A12
Description
Barrel Nuts
8
Thank you for purchasing Babymore If you need assistance, spare parts or you are unhappy with the goods
Call: 020 3475 5588
or email: [e-mail]
Item Qty
8
F
Description
Bolt - 20mm
Description
Bolt - 55mm

5
4 | P a g e
COMPONENTS
Item Description Qty Item Description Qty
1 Fixed Side 1 4 2
2 Drop Side 1
3 Base Slats 1
Cot End
2
Base Support Bar
1
23
4
5
4
5

X4
A / Bolts 55mm x 8
B / Barrel Nuts x 8
B x2
Top position
Middle position
Bottom position
A x2
A x2
A x2
A x2
3
4
4
Step 2
Choose 1 of 3 bases
position as show,
main diagram show
base panel install
onto the end panels,
with above fing.
Leave bolts
connection loosen
unl step 6
Step 1
5 | P a g e
5
5
3
F / Bolts 20mm x 8
Align and install base
slats onto base
support bars.
Use bolts F to secure
slat onto the support
bar, as diagram show.

6 | P a g e
Step 3
A / Bolts 55mm x 4
A x4
3
1
4
4
A
A
C / Bottom Pin x 2
Step 4
D / Top Pin x 2
1
3
C
C
D
D
x2
D
C
4
4
Install fixed side to
ends by pass (A)
bolts through
predrilled hole onto
cot ends.
Leave bolts
connection loosen
unl step 6
Refer to the
magnified diagram,
attach top pin (D) and
insert Botton pin (C)
onto both cot ends.
Do not over tight.

7 | P a g e
NON
2
3
1
4
4
INSIDE
OUTSIDE
Step 5
Ensure correct way
(Outside/Inside) of
dropside panel for
assembly. “Push” label
face outside.
Align and insert top pin
into top recess of dropside
panel, push cot end panels
outward to allow extra
space where required.
Maximum maress height mark:
Top of maress should be below this mark in al l posions.
NON
2
210
Step 6
Fully ghten all the
connecng bolts.
Rotate the bottom of drop
side panel, carefully align
the lower recess with
bottom pins on cot ends,
use your finger push down
the top of bottom pin,
allow it be inserted into
the long groove of plastic
tracks.
TEST THE DROP SIDE
OPERATE AS NEXT STEP

8 | P a g e
NON
2
1
Step 1
Step 2
Step 7
To lower the dropside ,
Li up the dropside from
centre, hold while using
your leg to push at centre
of boom bar inward,
then allow panel to slide
down to lower posion.
To raise the dropside,
Li up the dropside from
centre, hold while using
your leg to push at centre
of boom bar inward,
then pull up unl it clicks
into the locking posion.
Always verify that both
ends of the dropside are
locked in the up posion
whenever a child is in the
cot.

9 | P a g e
CONVERT TO DAY BED / BED
Step 2
E / Allen Key
Step 1
Remove the dropside ,
insert (C) Allen key
through the holes of
the dropside, push
down top of boom
pins, to remove the
dropside.
Disassemble the cot
by reverse the
assembly step 6 to
Step 1.
2
1
4
4
E / Allen Key
E
E
per diagram,
seperate the top of
ends with boom of
ends.

11| P a g e
Step 3
x 4
A / Bolts 55mm x 8
B / Barrel Nuts x 8
3
4
4
B x2
A x2
A x2
A x2
A x2
Use the above fing
aach base panel (3)
onto the cot end tops.
Ensure base label side
upward.
Fully ghten bolts

11 | P a g e
Due to constant update and improvement, some components may occasionally differ slightly from the diagrams shown
in these instructions.
Any spare components should only be thrown away after you have fully constructed your product. After disassembly, it is
important to retain all metal fixings and components should the product be returned to cot or bed mode in future.
We reserve the right to change the specifications of any piece of product without prior notice.
Care & Maintenance
To preserve the hand crafted quality of Babymore furniture, we recommend using a cotton cloth and a non-toxic
cleaner. Periodic use of furniture polish will maintain the good looks of your furniture. Scuff marks may be
removed with a damp cloth.
SIX MONTHS LIMITED WA RRANTY
We will replace any missing parts at the time of purchase or any defectiv item within 6 months period from the
date of original purchase. Please keep your receipt so that we may process your warranty request. This
warranty only covers new units with original packaging and ownership, and is not transferable. It does not cover
any used, second hand or demo models.
This warranty does not cover any damaged or defective parts that result from installation and assembly,
normal wear and tear, abuse, negligence, improper use, incidental damages or alteration to the finish, design,
and part or fitting of the cot. This in no way affects your statutory rights
Each Babymore item is a unique piece, made of high quality wood and material. Due to the handcrafted nature
of our products and our use of solid woods, each piece is unique and may contain irregular qualities, there will
occasionally be natural markings, miniscule burrs, or slight discolorations. These natural characteristics are
inherent in wood and are not considered manufacturing defects. Because of this, the merchandise will be
considered normal and of good quality and do not merit replacement.
Serial Number locate on label attached onto slat of mattess base.
Thank you for purchasing Babymore If you need assistance, spare parts or you are unhappy with the goods
Call: 020
3475 5588 or email: [e-mail]
3

4