Babymore VELVET User manual

1 | Page
INSTRUCTIONS
VELVET COT BED
VEL:V1/16
Babymore Ltd. 2016
Babymore

2| Page
IMPORTANT: READ CAREFULLY AND
RETAIN FOR FUTURE REFERENCE
INSTRUCTIONS FOR SAFE USE
The correct use and maintenance of your cot/bed will ensure it gives long and trouble-free use. Please ensure
everyone use your cot/bed know how to use it. The safety of your child is your responsibility.
• WARNING: Be aware of the risk of open fires and other sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the cot.
• WARNING: Do not use the cot/bed if any part is broken, torn or missing and use only spare parts approved
by Babymore.
• WARNING: Do not leave anything in the cot or place the cot close to another product which could provide a
foothold or present a danger of suffocaon or strangulaon, e.g. strings, blind/curtain cords, etc.
• WARNING: Do not use more than one maress in the cot.
• WARNING: When converted to a child’s bed, do not place this bed near heat sources, windows and other
furniture.
• The lowest base posion is the safest. Once your child is old enough to sit up unaided the base should be
used in the lowest posion only.
• The thickness of the maress chosen shall be such that the internal height (surface of the maress to the
upper edge of the cot frame) is at least 500mm in the lowest posion of the bed base and at least 200mm in
the highest posion of the bed base.
• The line engraved on the cot end indicates the maximum thickness of a maress that can be used with this
cot when the bed base is in the top posion.
•We recommend the use of a maress minimum size of 70cm by 140cm for this cot.
The length and width of maress shall be such that the gap between the maress and
the sides and ends does not exceed 30mm.
• Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not be placed
too close to other furniture or windows, and should be placed either ght to any wall or have a gap of
300mm between the wall and the side of the bed.
• Please ensure that all assembly fings always be ghtened properly before use. And fings should be
checked regularly and ghtened as necessary.
• Your cot/bed may be cleaned with a damp cloth. Never use bleach or harsh abrasives.
• To prevent injury from falls, once the child is able to climb out of the cot, the cot should no longer be used
for that child.
•This cot bed is intended for children aged from birth to 4 years approximately.
•The cot conforms to EN 716-1:2008 + A1:2013. When converted to bed, it conforms to BS 8509:2008 +
A1:2011.
With a thickness not
exceeding 10cm.

3 Page
Improper assembly can result in damage to your furniture or cause harm to
to ensure a safe and comfortable end assembly and keep for future use.
BEFORE ASSEMBLY
If you do find that any parts are missing or damaged or incorrect, contact customer services of above.
FITTINGS
A
12
4
B Bolts-60mm 8
Item Qty
Thank you for purchasing Babymore If you need assistance, spare parts or you are unhappy with the goods
Call : 020 3475 5588 Or email us at [email protected]
Bolts-30mm
C
Allen key
1
E
4
D
Base Bolts Cap Nuts

4 Page
COMPONENTS
Item Qty Item Qty
1 2
2 2
3 1
4 2
5 2
Description
Cot End Panel
Cot Side Panel
Base Slats
Description
Base Support Bar
Bed Side Support A
Bed Side Support B
6 2
1
1
2
3
6
5
4
4
2
5
6

ASSEMBLING THE COT
Step 1
B / Bolts 60 mm x 4
B
B
B
B
1
12
Page
5

6 Page
ASSEMBLING THE COT
The highest base position is only suitable for use until the baby is about three months old.
Step 2
Highest base level
C Base Bolt x 4
C
1
1
4
4
2
C
C
C
C

7 Page
ASSEMBLING THE COT
The middle base position is only suitable for use before the baby can sit up unaided
Step 2
Middle base level
C Base Bolt x 4
C
1
1
4
4
C
C
C
C

8 Page
Step 2
Lowest base level
ASSEMBLING THE COT
The lowest base position is the safest. Once your child is old enough to sit up unaided, the base
should be used in the lowest position only.
Tips
Adjusting the height of the base
Take one of the side panelss off, better view of the fittings and better grip on the components.
It's often useful to loosen the sides first and retighten afterwards, for easy manoeuvre components loose.
Consider loose slats at end of base and retighten afterwards, for easy access of fittings.
C Base Bolt x 4
C
1
1
2
4
4
C
C
C
C

9 Page
A / Bolts 30 mm x 4
Step 3
ASSEMBLING THE COT
1
1
3
D
D
D
A
AA
A
D
D / Cap Nuts 15mm x 4
4
C
D

Page
Step 4
ASSEMBLING THE COT
B / Bolts 60 mm x 4
Cot is ready for use
1
1
2
2
B
B
B
B
10

CONVERT TO DAY BED
A / Bolts 30 mm x4
11 Page
1
1
2
3
4
6
5
A
B
A
A
B
B
Change the cot to a bed as soon as your toddler shows any signs of attempting to climb out
B / Bolts 60 mm x4
Remove one side panel by reverse step
4 and add below
X2
X2

12 Page
CONVERT TO BED
B
A
A
B
4
4
1
1
A
A
A
B
B
B
5
6
6
A / Bolts 30 mm x8
Change the cot to a bed as soon as your toddler shows any signs of attempting to climb out
B / Bolts 60 mm x8
Remove BOTH side panels by reverse
step 4 and add below
X2
X2

13 Page
Due to constant updating and improvements, some components may occasionally differ slightly from the
diagrams shown in these instructions.
Any spare components should only be thrown away after you have fully constructed your product. After disassembly, it is
important to retain all metal fixings and components should the product be returned to cot or bed mode in future.
We reserve the right to change the specifications of any piece of product without prior notice.
Care & Maintenance
To preserve the hand crafted quality of Babymore furniture, we recommend using a cotton cloth and a non-
toxic cleaner. Periodic use of furniture polish will maintain the good looks of your furniture. Scuff marks may
be removed with a damp cloth.
SIX MONTHS LIMITED WARRANTY
We will replace any missing parts at the time of purchase or any defective item within 6 months period from
the date of original purchase. Please keep your receipt so that we may process your warranty request. This
warranty only covers new units with original packaging and ownership, and is not transferable. It does not
cover any used, second hand or demo models.
This warranty does not cover any damaged or defective parts that result from installation and assembly,
normal wear and tear, abuse, negligence, improper use, incidental damages or alteration to the finish, design,
and part or fiting of the cot. This in no way affects your statutory rights.
Each Babymore item is a unique piece, made of high quality wood and material. Due to the handcrafted
nature of our products and our use of solid woods, each piece is unique and may contain irregular qualities,
there will occasionally be natural markings, miniscule burrs, or slight discolora ons. These natural
characteristics are inherent in wood and are not considered manufacturing defects. Because of this, the
merchandise will be considered normal and of good quality and do not merit replacement.
Thank you for purchasing Babymore If you need assistance, spare parts oryou are unhappy with the goods
Call : 020 3475 5588 Or email us at [email protected]
Serial Number locaon: label aached onto slat of maress base.
Serial No: XX XXXX XXX XX -
1
3