Babymore MILO COT / BED User manual

INSTRUCTIONS
MILO COT / BED
MILO: V1/18
Babymore Ltd. 2018
1 | Pag e
<30m
x1

2 | Page
IMPORTANT: READ CAREFULLY AND
RETAIN FOR FUTURE REFERENCE
INSTRUCTIONS FOR SAFE USE
The correct use and maintenance of your cot/bed will ensure long and trouble free use. Please ensure
everyone use your cot/bed know how to use it. The safety of your child is your responsibility.
• WARNING: Be aware if the risk of open fires and other sources of strong heat, such as electric bar
fires, gas fires, etc. in the near vicinity of the cot.
• WARNING: Do not use the cot/bed if any part is broken, torn or missing and use only spare parts
approved by Babymore.
• WARNING: Do not leave anything in the cot or place the cot close to another product which could
provide a foothold or present a danger of suffocation or strangulation, e.g. strings, blind/curtain
cords, etc.
• WARNING: Do not use more than one mattress in the cot.
• WARNING: When converted to a child’s bed, do not place this bed near heat sources, windows and
other furniture.
• The lowest base position is the safest. Once your child is old enough to sit up unaided the base
should be used in the lowest position only.
• If your leave the child unattended in the cot, always make sure that the movable side is closed.
• The thickness of the mattress chosen shall be such that the internal height (surface of the mattress to
the upper edge of the cot frame) is at least 500mm in the lowest position of the bed base and at least
200mm in the highest position of the bed base.
• Do not use more than one mattress in the cot.
•We recommend the use of a mattress minimum size of 70 cm by 140 cm for this cot. With a thickness
not exceeding 10cm. the length and width of mattress shall be such that the gap between the
mattress and the sides and ends does not exceed 30mm.
• Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not be
placed too close to other furniture or windows, an should be placed either tight to any wall or have a
gap of 300mm between the wall and the side of the bed.
• Please ensure that all assembly fittings always be tightened properly before use. And fittings should
be checked regularly and tightened as necessary.
• The cot is only ready for use, when the locking mechanism(s) are engaged. Check the mechanism(s) is
fully engaged before use.
• Your cot/bed may be cleaned with a damp cloth. Never use bleach or harsh abrasives.
• To prevent injury from falls, once the child is able to climb out of the cot, the cot should no longer be
used for that child.
• This cot bed is intended for children aged from birth to 4 years approximately.
• The cot conforms to BS EN 716: 2017. When converted to bed, it conforms to BS 8509:2008+A1:2011.

FITTINGS
A12
D 2
Allen key 1
B Barrel nut 8
E 2
F
Item Qty
Lower Pin
Bolts-55mm
Upper Pin
C
Bolts-25mm 8
3 | Page
Thank you for purchasing Babymore If you need assistance, spare parts or you are unhappy with the goods
Call : 020 3475 5588 Or email us at [email protected]
Improper assembly can result in damage to your furniture or cause harm. Proper assembly is critical to safe end
result. Please read all instructions before assembly and keep for future use.
BEFORE ASSEMBLY
Read the instruction thoroughly before attempt assembly.
Unpack all the parts and identify against the components and fittings lists.
Do not discard any packaging until you are sure all the parts and fittings.
If any part/s missing or damaged or incorrect, contact customer services.
Construction is easier with help of another person, in the room of use, on soft clean level floor.
Follow step by step construction stages.

COMPONENTS
Item Description Qty
1 Cot End Panel 2
2 Foot 4
3 Fixed Side 1
4 Base Slat 1
5 Base Support Bar 2
6 Drop Side 1
13
4
5
5
6
1
2
2
2
2
4 | Page

ASSEMBLING THE COT
Step 2
Step 1
A /
B / Barrel Nut x 8
Bolts 55mm x 8
1
2
2
2
5
5
A x8
B x8
Top Position
Middle Position
Bottom Position
5 |P age
Do not fully tighten until step 8

A / Bolts 55mm x 4
C / Blots 25mm x 8
A x4
C x8
4
3
Step 3
Step 4
ASSEMBLING THE COT
6 |P age
Do not fully tighten until step 8

Step 6
Step 5
D / Lower Pin x2
E / Upper Pin x2
D x2
E x2
E
OUTSIDE
INSIDE
6
D
The Second Hole
ASSEMBLING THE COT
7 |P age
IMORTANT:
Ensure correct way
(Outside/Inside) of
Dropside Panel.
"PUSH" label face
outside
Align and insert top
gilde pin into top
recess of dropside
panel, if required,
loosen the bolts of
step 2 and step 3,
to create space.

Step 8
Step 7
D
D
OUTSIDE
Fully Tighten
Fully Tighten
Fully Tighten
3~5mm
1
5
ASSEMBLING THE COT
8 |P age
Rotate the bottom of
dropside panels, align
lower recess ot the
lower pins of cot end,
Push down the top of
retractable pin, insert
it to lower recess.
IMPORTANT:
Ensure both pins
insert into the long
groove of recess.
FULL TIGHTEN ALL
BOLTS.
DO NOT OVER
TIGHTEN.
Allow 3-5mm
even gap between
drop side and cot
ends.
COT READY FOR USE

Step 9
Step 1
UP
Step 2
Push In
ASSEMBLING THE COT
CONVERT TO DAY / BED
Step 1
Back-out
Back-out
Back-out
9 |P age
USE THE DROP SIDE
Lift the drop side to
top, hold, while use
your leg push lower
centre of panel
inward, then allow
the panel to slide
down / up until it
clicks into loscking
position.
ALWAYS VERIFY
BOTH ENDS LOCKED
INTO RAISED
POSITION, WHEN A
CHILD IN THE COT.
E /Allen Key x1
Use Allen Key to
remove lower pin out
of recess.
Reverse assembly step
6 and step 5 to
remove the drop side.
Loosen up the
connection botls for
spae of remove the
panel.

Step 2
D x2
E x2
10 |P age
Middle Position
CONVERT TO DAY / BED
Step 3
Remove cot feet and Upper pins
Change the base to
middle position.
BED READY FOR USE

Serial No: xx xxxx xxx xx-
11 |P age
Care & Maintenance
SIX MONTHS LIMITED WARRANTY
Thank you for purchasing Babymore If you need assistance, spare parts or you are unhappy
with the goods Call : 020 3475 5588 Or email us at [email protected]
Due to constant update and improvements, some components may occasionally differ slightly from the
diagrams show in these instructions.
Any spare components should only be thrown away after you have fully constructed your product.
After disassembly, it is important to retain all metal fixings and components should the product be returned to
cot or bed mode in future.
We reserve the right to change the specifications of any piece of product without prior notice.
To preserve the hand crafted quality of furniture, we recommend using a cotton cloth and a non-toxic cleaner.
Periodic use of furniture polish will maintain the good looks of your furniture. Scuff marks may be removed
with a damp cloth.
We will replace any missing parts at the time of purchase or any defective item within 6 months period from
the date of original purchase. Please keep your receipt so that we may process your warranty request. This
warranty only covers new units with original packaging and ownership, and is not transferable. It does not
cover any used, second hand or demo models.
This Warranty does not cover any damaged or defective parts that result from installation and assembly,
normal wear and tear, abuse, negligence, improper use, incidental damages or alteration to the finish, part or
fitting of the cot. This in no way affects your statutory rights.
Each Babymore item is a unique piece, made of high quality wood and material. Due to the hand crafted
nature of our products and our use of natural material, each piece is unique and may contain irregular
qualities, there will occasionally be natural markings, minuscule burrs, or slight discolorations. These
characteristics are inherent in the material and are not considered manufacturing defects. Because of this, the
merchandise will be considered normal and do not merit replacement.
Serial Number location: Label attached on slat of mattress base.