Backyard Creations 272-3265 User manual

HANGING LOUNGER
272-3265
Instruction Manual

Assembly Instructions for Hanging Lounger, Model # 4717RB, SKU 272-3265
Thank you for purchasing the Hanging Lounger. We hope it provides years of enjoyment. Please read and follow the assembly and
safety instructions for proper assembly and safe use of this product. If you are missing parts or if there are damaged parts, please call
our customer service department at 800-295-6758 or, email [e-mail] before retuning to the retailer.
Part A
Part B
Part C
Part D
Parts E (x2)
Part F
Parts G (x2)
Part H
Part I
Parts J (x2)
Part K
Part L
Part M
Part N
One person should be able to assemble this product, but for easier assembly a second person is advised.

HARDWARE
Hardware and
assembly tools are
located within the
Hardware bag.
Keep bag for
hardware storage
when not in use.
Part O
Parts P
Parts Q
(x2)
Parts R
Parts S (x6)
Part T Part U
Part V (x4)
Part W (x2)
Part X
Parts Y
Part Z (x2)
Parts P : One 3 ½” 16mm double threaded bolt with two 16mm washers and 2 acorn nuts.
Parts Q : Two 2 ¾” x 13mm bolts with two 13 mm lock nuts and four 13mm washers.
Parts R : One 3 ¾” x 13mm bolt with one 13 mm lock nut and two 13 mm washers.
Parts S: Six plastic bolt caps
Part T: Threaded connecting link.
Part U: Closed S-hook.
Parts V: Four 1 3/8” x 13mm Hex head bolts.
Parts W: Two ¾” Hex head bolts.
Part X: Hex Wrench
Part Y: Hand Knob with square nut.
Parts Z: Two Open ended wrenches.

Step 1: Locate Part A and Part B. Connect Part B to Part A by
inserting end of Part B onto swedge end of Part A aligning holes as
shown in (Diagram 1). Place a 13mm washer onto Part Q (2 ¾”
Bolt) and insert through both Part A & B (Box 1), Place a second 13
mm washer onto bolt and then a 13 mm lock nut (Box 2). Tighten
with the open ended wrenches (Part Z)
Box 1 Box 2 Box 3
Part APart B
S
T
E
P
1
Step 2: Locate Part D. Connect to Part B by placing Part B between
the metal flanges of Part D, and align the holes of the flanges with
the hole about halfway along Part B as shown in (Diagram 2). Place a
16 mm washer onto Part P (3 ½” double threaded bolt) and insert
through metal flange of Part D through part B, and the second metal
flange of Part D. Place another 16 mm washer on exposed end of
bolt, and then an acorn nut. (Box 4) Tighten with the two open
ended wrenches. (Part Z)
Diagram 1
Box 4
S
T
E
P
2
Diagram 2
Note: The connection of Part D
with B will still be loose after
tightening acorn nuts allowing
Part D (the leg) to swivel
slightly.
Step 3: Locate parts C and H. Slide part H onto Part C through the
O-bracket of Part H, from the base of Part C (Box 5) to just before
the attached hanging ring. (Box 6)
S
T
E
P
3
Box 5 Box 6

Step 4: Locate Parts Y. Insert square nut into nut slot on bottom of O-ring of Part H, as shown in Box 7. Then insert hand
knob of part Y through the hole of part H as in Box 8. Straighten the Part H assembly so the hand knob is just below the
hanging hook as shown in Box 9, then tighten hand knob so Part H stays in place.
Box 7 Box 8 Box 9
S
T
E
P
4
Box 10 Box 11
Box 12
S
T
E
P
5
Part C
Part B
Step 5: Place bottom end of Part C over the swedge end of Part B as
shown in Box 10. Align holes of Part B and C and insert Part Q (2 ¾”
bolt with 13 mm washer) through hole until bolt shows through
opposite side of Part C as shown in Box 11. Place second 13 mm
washer onto end of bolt then the 13 mm lock nut. Tighten securely
using the open ended wrenches (Parts Z) as in Box 12.
S
T
E
P
6
Step 6: Find Parts E. Identify the ends with the crimp over the hole as
shown in photo. Hold both Parts E with crimps facing each other and
proceed to Step 7.