Badger Basket Elegance 00830 User manual

5.1/0207/TG
PRODUCT NAME:
Elegance™ Round OR Elite™ Oval
Baby Bassinet with Bedding
PRODUCT MODEL NUMBERS:
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday to Thursday 7:30 AM-4:30 PM CST), part[email protected]
PLANT AND GENERAL OFFICE: PO Box 227, Edgar, WI 54426-0227 • Phone: [phone] • Fax: [phone]
CORPORATE OFFICE: 111 Lions Dr., Suite 220, Barrington, IL 60010
Page 1 of 5
BABY BASSINET
ASSEMBLY INSTRUCTIONS
Adult Assembly Required.
Save these instructions for future use.
ELEGANCE™ MODEL #’s:
00825 - Black Frame with Sage Waffle 00826 - Black Frame with Ecru Waffle
00827 - White Frame with White Eyelet 00829 - Cherry Frame with White Eyelet
00830 - White Frame with Ecru Waffle 00831 - White Frame with Sage Waffle
00832 - White Frame with Sage Toile 00836 - White Frame with Pink/White
00834 - White Frame with Ecru/Beige Gingham 00838 - Black Frame with Black Toile
00835 - White Frame with White/Sage Gingham
00837 - White Frame with Blue/White
ELITE™ MODEL #’s:
00850 - White Frame with White/Sage Gingham
00852 - White Frame with Ecru Waffle/White Pleats
00854 - White Frame with Ecru Waffle/Ecru Pleats
00853 - White Frame with Sage Waffle 00855 - Natural Frame with Ecru Waffle
00856 - Cherry Frame with White Eyelet

5.1/0207/TG
TOOLS NEEDED:
Phillips Screwdriver*
Hammer
* Power screwdriver is helpful but
be careful not to damage the bassinet
PARTS INCLUDED:
(A) 2 - End Panels
(B) 2 - Rails
(C) 4 - Long Bolts
(D) 1 - Shelf
(E1,2,3) 4 each -
Wheels, Bolts, Knobs
(F) 4 - L-Brackets
(G) 16 - Short Bolts
(H) 1 - Bassinet Body
(not shown)
(I) 1 - Fabric Skirt
(J) 1 - Curved Canopy Pole
(not as shown)
(K) 1 - Canopy Frame
(L) 1 - Fabric Canopy
(M) 1 - Fabric Bumper
(N) 1 - Fitted Fabric Sheet
(O) 1 - Mattress
(not shown)
Ax2
Bx2
Dx1
Ix1
Jx1*
Cx4
Hardware not shown to scale
Fx4
*Part J is curved.
*It is not straight as shown.
E2x4
Gx16
PARTSAND HARDWARE:
BEFORE YOU BEGIN ASSEMBLY:
Check all parts and hardware listed. If anything is missing, please
DO NOT call the store or return the product to them. Contact us for assistance. Most
problemsareresolvedwithoutyou needing toleave home.When emailing or callingus,
pleasehave this instructionmanual andyour productmodel numberready.
For faster service, go to http://www.badgerbasket.com/parts
NOTE: Elegance™Round models should
be assembled in the room where you
intend to use it unless your doorways are
wider than 33” (83.8 cm).
Page 2 of 5
Mx1
Lx1
Kx1
Nx1
E1x4 E3x4

5.1/0207/TGPage 3 of 5
STEP 2 - PICTURE 2A (this page) and 2B (on page 3):
Using the FOUR L-BRACKETS (F) and the SIXTEEN
SHORT BOLTS (G), bolt the BASSINET BODY (H) to the
BASSINET STAND.
Put the bassinet body upside down, and then put the bassinet
stand upside down on top of the bassinet body as shown in
PICTURE 2B.
Line up the four pairs of holes on the END PANELS (A)
with the four pairs of holes on the BASSINET BODY (H).
PositiontheL-BRACKETS(F) onthe INSIDEOFTHE END
PANELS and secure them using the SIXTEEN SHORT
BOLTS (G).
WARNING !
Once the bassinet stand is
assembled, do not disassemble
and reassemble for future use.
Doing so may affect the
stability and safety.
PICTURE 1B
A
B
A
DB
PICTURE 1A
STEP 1 - PICTURES 1A and 1B:
Attach ONE CASTER WHEEL (E) to each leg of the END PANELS (A) using ONE
BOLT(E2) and ONE KNOB (E3) for each WHEEL(E1). The knobs go on the inside. The
square hole on the wheel goes on the outside so the head of the bolt “locks” into the hole.
Take ONE END PANEL (A) and attach the TWO RAILS (B) using TWO LONG BOLTS
(C). The grooves on the railsface inwards. TheT-Nuts pre-installedon the endpanels
face out.
Slide the SHELF (D) into the grooves with the white warning label facing up. Then attach
the second END PANEL (A) to the TWO RAILS (B) using TWO LONG BOLTS (C).
PICTURE 2A
H
A
These assembly instructions cover both Elegance™
ROUND bassinets and Elite™OVAL bassinets.
The shape of the units is different but the parts and
assembly steps are identical.
IMPORTANT!
THE T-NUTS
ON THE END
PANELS ARE
ON THE
OUTSIDE.
THE
BRACKETS
ARE ON THE
INSIDE.

5.1/0207/TGPage 4 of 5
STEP 3 - PICTURE 3:
With the bassinet in its upright position, wrap the FABRIC SKIRT
(I) around the lower rim of the BASSINET BODY (H) pressing
the grip tape strips together as you go around. Begin and end at the
rear center where the metal spindle is located (the ends may overlap).
STEP 4 - PICTURE 4:
There are two holes in the metal spindle on the bassinet body to
height adjust the canopy. Insert the METAL CANOPY POLE (J)
into the metal spindle on the bassinet body (H) and line up a hole
on the metal spindle with the push button on the canopy pole. Make
sure the push button snaps into the hole.
STEP 5 - PICTURE 5:
Insert the two free ends of the CANOPY FRAME (K) into the top
of the CANOPY POLE (J). Tap gently with a hammer until the
ends of the frame are fully seated inside the pole.
Place the FABRIC CANOPY (L) onto the CANOPYFRAME (K).
Secure it to the frame with the ribbons and/or the grip tabs.
I
H
PICTURE 3
PICTURE 2B
H
A
A
J
Pushbutton
on canopy
pole (J) must
snap into the
hole on the
metal spindle.
PICTURE 4
PICTURE 5
J
K
F

5.1/0207/TG
•SUFFOCATION HAZARD - Infants can suffocate:
»in gaps between an extra pad and the side of the bassinet,
»on soft bedding.
NEVER add a mattress, pillow, comforter, or padding. Use ONLYthe pad
and/or bedding provided by the manufacturer. If a sheet is used with the pad,
use only the one provided with the bassinet or one that is from Badger Basket
Company or one that is specifically designed to fit the dimension of the the
mattress provided.
• TO REDUCE THE RISK OF SIDS: pediatricians recommend that healthy
infants be placed on their backs to sleep, unless otherwise advised by your
physician.
• DO NOT move or carry the bassinet with your baby inside of it.
• DO NOT allow other children or pets to climb into or onto the bassinet when
your infant is inside.
• DO NOT attach or place toys with strings in or around the basket. Strings can
cause strangulation or choking.
•Keepbassinet away from stoves, heaters, camp fires/flames, fireplaces, stairs, open windows, window blinds, running or
standing water, and any other hazard which could cause injury to your baby.
• NEVER use plastic bags inside the basket such as to cover the mattress.
• Bassinet should always be placed on a firm, flat surface. It should never be placed near stairs or on tables or elevated
surfaces.
Page 5 of 5
Check ALL OF THE HARDWARE to make sure everything is fully tightened. Carefully review the safety
informationbelow.NOTE: Your bedding and canopy may vary in color, pattern, and/or style from what is shown here.
CARE INSTRUCTIONS: Wipe bassinet clean with a damp cloth and mild detergent as needed. Bedding can be
machine washed on cold, gentle cycle, and air dried or tumble dry on low or no heat. Iron on lowest setting for poly/
cotton. Secure all grip tabs together before washing so they do not catch on the bedding or ribbons.
M
N, O
PICTURE 6
STEP 6 - PICTURES 6 and 7:
Position the FABRIC BUMPER (M) inside the BASSINET
BODY (H). Position and then secure the tabs on the bumper to
the thicker dowels and tie the ribbons, and then tie the remain-
ing ribbons to the thinner dowels.
NOTE: Be sure the bumper is secured and check the rib-
bons regularly to make sure they stay tied. Loose bedding
can be a danger to your baby.
Put the FABRIC FITTED SHEET (N) onto the MATTRESS
(O) and place them inside the bassinet. Additional sheets are
sold separately! Contact us or check our web site for more in-
formation or to find a retailer.
FALL HAZARD: To help prevent falls, please note this
bassinet is a safe place for your newborn to sleep until Baby is
4 months old, 20 lbs. (9.09 kg), OR when Baby can push up,
roll over, or crawl - whichever limit comes first.
PICTURE 7
WARNING - FAILURE TO FOLLOW
THESE WARNINGS AND THE
INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH: