Badger Basket 02241 User manual

1.2/0407/TG
PRODUCT NAME:
Sleigh Style Baby Changing Table with Drawer
PRODUCT MODEL NUMBERS:
02240 - WHITE, 02241 - NATURAL
02242 - CHERRY
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday to Thursday 7:30 AM-4:30 PM CST)
Web: http://www.badgerbasket.com/parts • E-mail: part[email protected]
PLANT AND GENERAL OFFICE: PO Box 227, Edgar, WI 54426-0227 • Phone: [phone] • Fax: [phone]
CORPORATE OFFICE: 111 Lions Dr., Suite 220, Barrington, IL 60010
BABY CHANGING TABLE
ASSEMBLY INSTRUCTIONS
Adult Assembly Required.
Save these instructions for future use.
Page 1 of 5

1.2/0407/TG
TABLE PARTS INCLUDED:
(A1) 1 - Right Outside Drawer Track
(A2) 1 - Left Outside Drawer Track
(B1) 1 - Right End Panel
(B2) 1 - Left End Panel
(C) 6 - ½” Screws
(D) 16 - Black Pegs
(E) 2 - Top Rails
(F) 6 - Shelf Rails
(G) 16 - 1¾” Bolts
(H) 3 - Shelf Panels (not shown)
(I) 1 - Safety Belt
(J) 1 - Metal Support Bar
(K) 2 - 5/8” Screws
(L) 1 - Mattress Pad (not shown)
DRAWER PARTS INCLUDED:
(M) 4 - Metal Pins
(N) 1 - Left Side Panel
(O) 1 - Right Side Panel
(P) 1 - Back Panel
(Q) 4 - Round Metal Cams
(R) 1 - Bottom Panel
(S) 1 - Front Panel
(T1) 1 - Left Inside Drawer Track
(T2) 1 - Right Inside Drawer Track
(C) 6 - ½” Screws
NOTE: Parts & Hardware diagrams not to scale.
TOOLS NEEDED:
Phillips Screwdriver
Standard Screwdriver
Page 2 of 5
Px1
Sx1
Rx1
Nx1
Ox1
B1x1
Fx6
B2x1
Ix1 Jx1
Ex2
A1x1
Dx16
Cx6
T1x1
Gx16
Kx2
A2x1
T2x1
Mx4 Qx4
PARTSAND HARDWARE:
BEFORE YOU BEGIN ASSEMBLY:
Check all parts and hardware listed. If anything is missing, please
DO NOT call the store or return the product to them. Contact us for
assistance. Most problems are resolved without you needing to leave home. When
emailingor callingus, pleasehave thisinstruction manualand yourproduct model
numberready. For fastest service, goto http://www.badgerbasket.com/parts

1.2/0407/TGPage 3 of 5
STEP1 - PICTURE 1:Attach the TWO OUTSIDE DRAWER TRACKS (A1 andA2) to the TWO END PANELS (B1, B2)
using SIX ½” SCREWS (C) (three screws for each track). Line up the first hole behind the track wheel so that all three screw
holes on (B) match up to holes on (A), and the narrower end of (A) lines up with the end of the track board.
STEP 2 - PICTURE 2: Insert the SIXTEEN BLACK PEGS (D) into the peg holes on the ends of the TWO TOP
RAILS (E) and the SIX SHELF RAILS (F). Push the thinner end of the peg into the hole until the wider end is flush
with the wood.
STEP 3 - PICTURE 3: Attach ONE TOP RAIL (E) and THREE SHELF RAILS (F) to ONE END PANEL (B2 is
shown, but you can begin with B1 if desired) using FOUR 1¾” BOLTS (G).
Insert the PEGS (D) on the RAILS (E, F) into their pre-drilled holes on the END PANEL (B2) to line up the
holes for the BOLTS (G). The grooves on the SHELF RAILS (F) face in and line up with the shelf grooves on the END
PANEL (B2).
STEP 4: See PICTURE 4. Repeat Step 3 to attach the remaining TOP RAIL (E) and THREE SHELF RAILS (F) to the
END PANEL (B2).
PICTURE 1
Track Board
B1
A1
Narrow End
EF
DD
PICTURE 2
E
B2
FF
F
PICTURE 3 PICTURE 4
E
FFF
STEP 5 - PICTURE 5: Rest the table on the END PANEL (B2). Insert the THREE SHELF PANELS (H) into the
grooves on the SIX SHELF RAILS (F) with the white or colored sides (depending on your model) of the shelves facing
up. Be sure the shelves are seated into the grooves on all three sides.
B2

1.2/0407/TGPage 4 of 5
PICTURE 7C
PICTURE 8
STEP 6 - PICTURE 6:
Attach the SECOND
END PANEL (B1) to the
TWO TOP RAILS (E)
and SIX SHELF RAILS
(F) using EIGHT 1¾”
BOLTS (G).
STEP 7 - PICTURES 7A,
7B and 7C:
Note: This step can
also be completed with the
table upside down to make
iteasier.See PICTURE
7A. Slip one end of the
SAFETY BELT (I)
between the TOP RAIL
(E) and the TOP SHELF
RAIL (F).
H
PICTURE 5
B2
HHB1
PICTURE 6
PICTURE 7B
I
F
EJ
EF
I
H
PICTURE 7A
See PICTURE 7B. Using the pre-made hole on the
SAFETY BELT (I) and the pre-drilled hole on the
underside of the TOPSHELF RAIL (F), sandwich the
end of the SAFETY BELT (I) between the METAL
SUPPORT BAR (J) and the top shelf rail as shown and
secure with ONE 5/8” SCREW (K).
See PICTURE 7C. Secure the other end of the
SAFETY BELT (I) and the other end of the METAL
SUPPORT BAR (J) using the second 5/8” SCREW
(K).
STEP 9 - PICTURE 9: Insert the METAL PINS (M), and the wooden pegs, on the LEFT (N) and RIGHT SIDE
PANELS (O) into the holes on the side edges of the BACK PANEL (P). Be sure all of the shelf grooves are lined up.
Insert TWO ROUND METAL CAMS (Q) into the holes on the BACK PANEL (P) with the arrows on the cams
pointing towards the heads of the metal pins. Turn the cams clockwise using a standard screwdriver until they lock over
the heads of the pins. Insert the BOTTOM PANEL (R) into the grooves and be sure it’s seated on all three sides.
STEP 10 - PICTURE 10: Repeat the pin and cam procedure from Step 9 to attach the FRONT PANEL (S) to the
LEFT (N) and RIGHT SIDE PANELS (O). Be sure the BOTTOM PANEL (R) is properly seated in the grooves on all
four sides.
STEP 11 - PICTURE 11: With the drawer upside down, attach the TWO INSIDE DRAWER TRACKS (T1 and T2) to
the SIDE PANELS (N, O) using the pre-drilled holes and THREE ½” SCREWS (C) for each track. The wheels on the
tracks line up with the back edge of the drawer.
STEP 8 - PICTURE 8: NOW YOU
WILLASSEMBLE THE DRAWER!
Take the FOUR METAL PINS
(M) and screw them into the
pre-installed threaded plastic jackets on
drawer parts N, O, and S. Screw in the
pins only as deep as their threads.

1.2/0407/TGPage 5 of 5
N
O
P
R
PICTURE 9 PICTURE 10
S
STEP12 - PICTURE 12: Insert the drawer into the changing table. Angle the drawer so that you can slide the wheels
on the inside tracks (T) over and behind the wheels on the outside tracks (A); then holding the drawer level push it all
the way into the table. When properly installed the drawer will glide in and out smoothly and the wheels act as a stopper
to keep the drawer from falling out when fully opened.
Place the MATTRESS PAD (L) onto the TOP SHELF (H)
underneath the SAFETY BELT (I).
PICTURE 11
T2
PICTURE 12
L
! ! WARNING ! !
READ ALL INSTRUCTIONS before use of this changing table. Keep instructions for
future use. Use only the changing pad provided by Badger Basket. Do not use the
changing table if it is damaged or broken. FALL HAZARD - To prevent death or
serious injury, always keep baby within arm’s reach. NEVER leave your baby
unattended, not even for a moment, when you are changing Baby’s diaper.
ALWAYS use the safety belt; and as an extra precaution keep at least one hand
on your baby at all times. DO NOT allow any children to climb or play on the table. NEVER load
the drawer with items weighing more than a total of five (5) pounds (2.3 kg). NEVER lean on the
drawer when it’s open and never use the drawer as a surface for changing your baby.
Periodically check to make sure all the bolts and screws remain tight and that the drawer is
properly aligned in its tracks.
USE AND CARE INSTRUCTIONS:
Suitable for use with children up to 30 pounds (13.64 kg). Wipe the table, pad, and safety belt clean with a
damp cloth and mild soap as needed.
YOUR CHANGING TABLE IS ASSEMBLED!
DO NOT USE THIS PRODUCT UNTILYOU HAVE
REVIEWED THE SAFETYINSTRUCTIONS BELOW!
Remember that you can accessorize this table with up to
four Badger Nursery Baskets (sold separately)!
Browse our selection at www.badgerbasket.com! B2
B1