BainUltra MIA Series User manual

controls - user guide
important information for the installer
and the owner
included : using the mia®series controls
important: to be kept for the owner
The quest for your wellness™

CONTROLS USER GUIDE
3
www.bainultra.com
Printed in Canada. Copyright © January 2010 BainUltra Inc. All rights reserved. 45220001
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
table of contents
THE MIA® SERIES CONTROLS
INSTALLATION 4
USER GUIDE 5 - 15
MAINTENANCE 16 - 18
TROUBLESHOOTING 19 - 20
WARRANTY 21 - 22
DRILLING TEMPLATES 23 - 26
956, chemin Olivier
Saint-Nicolas (Québec)
G7A 2N1
T 418.831.7701 1.800.463.2187
F 418.831.6623 1.800.382.8587 [email protected]

4
CONTROLS USER GUIDE |THE MIA® SERIES CONTROLS
1 800 463.2187 From 8 a.m. to 8 p.m. Monday to Thursday (EST) .From 8 a.m. to 5 p.m. on Friday (EST)
Printed in Canada. Copyright © January 2010 BainUltra Inc. All rights reserved. 45220001
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
THE MIA®SERIES CONTROLS
MIa®& MIaplus® contRols
INSTALLATION
Determine the most convenient location, on either
the wall or the deck, to install the control module or
consult the specifications sheet for the suggested
location. To avoid drilling in an air intake zone or an
electric component, always check under the deck
before drilling. If you have to install the control to the
wall, remove the protective film of sticker behind the
control. You can add a silicone bead to secure it.
Refer to the drilling template on the last page for the
location and diameter of the holes.
LOCATION
DRILLING
INSTALLING THE TOUCHPAD
REQUIRED TOOLS
1Push wiring through drilled holes.
2Remove protective film from watertight
seal.
3Secure touchpad into place on either the
podium or the wall by using 2, 8-32 x 1”
studs and 2 wing nuts.
4Tighten sufficiently to insure seal is airtight.
1Fine teeth jigsaw
2Drill
31/4 in. drill bit
• If control was not factory-installed, it will be attached to the turbine.
WARNING
MIA®& MIAPLUS®CONTROLS - INSTALLATION

THE MIA® SERIES CONTROLS |CONTROLS USER GUIDE
5
www.bainultra.com
Printed in Canada. Copyright © January 2010 BainUltra Inc. All rights reserved. 45220001
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
THE MIA®SERIES CONTROLS
MIa®
USER GUIDE
The Mia®control panel comes standard with the
following baths:
• Azur
• BasaTM
• Thalassa
•Increase or decrease air jet pressure
•Activate Drying cycle function
MAIN FUNCTIONS
ON/OFF
On
Press the (on/off) key to start or to stop the tur-
bine and the Mia®control panel.
ADJUST AIR JET PRESSURE
TO ACTIVATE THE DRYING CYCLE
Air jet pressure can be adjusted for maximum
comfort and a remarkably effective massage.
Default pressure is set to 60%.
Increase or decrease the pressure of the air jets
by repeatedly pressing the or keys until the
desired intensity is reached.
This function completely drains the conduits and
dries them for 90 seconds, regardless of whether
or not the system was activated. By eliminating any
water left in the conduits, the Drying cycle ensures
perfect hygiene.
• No stagnant water
• No water left over from the previous bath
To activate the Drying cycle, press .
The operation will cease after 90 seconds. If you
do not activate the function, the drying process
will begin automatically after 15 minutes. If the
bath is used for soaking only, activate the drying cycle
manually by pressing . You can use the Drying
cycle function immediately after a Hydro-thermo
massageTM session or whenever you wish.
NOTE • The heat for the heated backrest is controlled simultaneously with the intensity
of the jet pressure.
MIA®- USER GUIDE

6
CONTROLS USER GUIDE |THE MIA® SERIES CONTROLS
1 800 463.2187 From 8 a.m. to 8 p.m. Monday to Thursday (EST) .From 8 a.m. to 5 p.m. on Friday (EST)
Printed in Canada. Copyright © January 2010 BainUltra Inc. All rights reserved. 45220001
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
THE MIA®SERIES CONTROLS
MIaplus®
USER GUIDE
The Mia®control panel comes standard with the
following lines of baths:
•MeridianTM
•Origami®
•Thermal
•Amma®
•TMU
•EleganciaTM
Settings are automatically saved until they are modified.
•Adjust air jet pressure
•Select duration of session
•Select light color (Chromatherapy option)
•Adjust backrest temperature
•Personalize session settings for up to 4 different users
•Personalize drying cycle for air jet conduits
•Lock controls when bath is not in use
•Adjust screen contrast
•Select display language
MAIN FUNCTIONS
MiaPlus®lets you personalize your Hydro-thermo massage
®
with
the following functions and options:
KEYS AND FUNCTIONS
Press this key to start or to stop the turbine and the
MiaPlus®control panel.
Press this key to return to function adjustment.
The Massage function appears on the screen
by default.
Press either of these keys to navigate the main
menu of the MiaPlus®control panel.
Press the key to see the next function.
Functions are displayed in the following order:
•Massage (air jet pressure)
•Duration
•Chroma (Chromatherapy option)
•Backrest (heated backrest)
•Care
•Save
•Drying cycle
•Lock
•Contrast (screen contrast)
•Language
•Contact us
Press either of these keys to navigate the options
of each function.
Press the key to go up.
Press the key to go down.
Press this key to save the selected options and
settings.
MIAPLUS®- USER GUIDE

THE MIA® SERIES CONTROLS |CONTROLS USER GUIDE
7
www.bainultra.com
Printed in Canada. Copyright © January 2010 BainUltra Inc. All rights reserved. 45220001
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
THE MIA®SERIES CONTROLS
MASSAGE
DURATION
CHROMA (OPTION)
• Off Deactivates the chromatherapy function.
• Violet Immunizing and relaxing. Boosts the immune system,
detoxifies the body, and reduces stress.
• Blue Soothing and relaxing. Reduces arterial pressure and
hyperactivity and soothes the soul.
• Green Provides calm and balance. Relaxes entire body and
stabilizes emotions.
• Yellow Digestion and creativity. Helps digestion and regularity and
calms brain activity.
• Orange Healing and pain relief. Boosts respiratory system and
soothes aching muscles.
• Red Stimulating and exciting. Activates circulation and wakes up
the senses.
• Scan Goes through each color in turn.
THE CHROMA FUNCTION FEATURES EIGHT OPTIONS
This function allows the user to regulate air jet
pressure for personalized comfort and a remarkably
effective Hydro-thermo massageTM. The default pres-
sure is the same for the previous bath.
Increase or decrease the pressure of the air jets
by repeatedly pressing the or key until the
desired pressure is reached. Pressure increases
in 10% increments.
Pressing is optional.
This function lets you program the duration of your
bath from 5 to 30 minutes. The selected duration
will remain in the memory until it is modified.
To select the Duration, press the key on the
menu until the Duration function is displayed.
Select the desired duration using the or keys.
Pressing is optional.
Use the arrows or or the key to return to
the basic Massage screen.
This function uses color to provide increased
comfort to body and soul.
To use the Chroma function, press the key on
the menu until the Chroma function appears on
the screen.
•To turn off the Chroma function,
select Off.
NOTE • Should you not see the colors on the screen, pressing the first time will start the color scan.
Pressing a second time will freeze the lights on their color, and the third time will turn the lights off.
MIAPLUS®- USER GUIDE

8
CONTROLS USER GUIDE |THE MIA® SERIES CONTROLS
1 800 463.2187 From 8 a.m. to 8 p.m. Monday to Thursday (EST) .From 8 a.m. to 5 p.m. on Friday (EST)
Printed in Canada. Copyright © January 2010 BainUltra Inc. All rights reserved. 45220001
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
THE MIA®SERIES CONTROLS
CHROMA (NEXT)
Choosing a color
Choose the desired color using the and keys.
Press to validate your choice of color.
Selecting Scan
Select the Scan option using the or keys.
Press to validate your choice.
Use the arrows or or the key to return to
the basic Massage screen.
MIAPLUS®- USER GUIDE
BACKREST
For maximum relaxation and exceptional comfort,
one or two heated backrests can be installed in
your bath and heated individually.
Select the Backrest function by pressing the key
until the Backrest function is displayed.
Four options are available:
• Off
• Low
• Medium
• High
NOTE: Models with 2 backrests will specify backrest
1 and backrest 2.
Choose the desired option using the or keys.
Press to validate your choice.
Use the arrows or or the key to return to
the basic Massage screen.
NOTE: Selecting the Off option will turn off the
backrests.

THE MIA® SERIES CONTROLS |CONTROLS USER GUIDE
9
www.bainultra.com
Printed in Canada. Copyright © January 2010 BainUltra Inc. All rights reserved. 45220001
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
THE MIA®SERIES CONTROLS
CARE
SAVE
This function lets you vary air jet intensity for a deeper
or gentler massage.
To select the Care function, press the key
on the menu until the Care function appears.
Six options are available:
• Massage – Even intensity throughout
the session
• Wave – Jet intensity cycles from 10% to
maximum desired intensity
• Bather 1, 2, 3, 4 – Stores each
bather’s selection
Use the or keys to select an option.
Press to validate your choice.
Use the arrows or or the key to return to
the basic Massage screen.
The MiaPlus®control system lets you save up to four
personalized presets. This save function lets you
conveniently preselect settings adapted to various
users or purposes. Simply set the functions and
options according to your tastes and save them
under Bather 1, Bather 2, etc. These personalized
settings will stay saved until modified.
Select a bather and save personalized settings
Press the key on the menu until the Save
function appears.
Use the or keys to select a user number.
Press .
Use the arrows or or the key to return to
the basic Massage screen.
Repeat these steps for each user.
MIAPLUS®- USER GUIDE

10
CONTROLS USER GUIDE |THE MIA® SERIES CONTROLS
1 800 463.2187 From 8 a.m. to 8 p.m. Monday to Thursday (EST) .From 8 a.m. to 5 p.m. on Friday (EST)
Printed in Canada. Copyright © January 2010 BainUltra Inc. All rights reserved. 45220001
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
THE MIA®SERIES CONTROLS
DRYING CYCLE
This function completely drains the conduits and
dries them for 90 seconds. By eliminating any
water left in the conduits, the Drying cycle
ensures perfect hygiene.
• No stagnant water
• No water left over from the previous bath
Drying is mandatory after a Hydro-thermo
massageTM session.
Two options are available:
• Daily
• After Bath
Even when the daily drying cycle is programmed,
the automatic drying cycle will activate after
each use.
Select After Bath
The After Bath option lets you program the
Drying cycle to start up to 60 minutes after a bath.
To select the After Bath option, press the key
on the menu until the Drying cycle function
appears.
Use the and keys to select the After Bath
option.
Press .
Dry Delay is displayed.
Press the key to select a value from 5 to 60
minutes.
Press to validate.
Use the arrows or or the key to return to
the basic Massage screen.
If no value is selected, the Drying cycle will start
up automatically 15 minutes after the bath.
MIAPLUS®- USER GUIDE

THE MIA® SERIES CONTROLS |CONTROLS USER GUIDE
11
www.bainultra.com
Printed in Canada. Copyright © January 2010 BainUltra Inc. All rights reserved. 45220001
Some products, specifications, and services mentioned in this manual are described in pending patent applications or are protected by patents.
THE MIA®SERIES CONTROLS
DRYING CYCLE (NEXT)
Select Daily
The Daily option lets you dry and clean the air jet
system conduits at a specific time of day rather
than within an hour of a Hydro-thermo massageTM
session.
To select the Daily option, press the key on the
menu until the Drying cycle option appears.
Use the and keys to select the Daily option.
Press .
Start Time is displayed.
Use the or keys to select the time of day the
Drying cycle function should start.
Press .
Current Time is displayed.
Press and hold the or keys or press them
repeatedly to set the preprogrammed current time
in 10 minute slots.
Press .
Once the Daily option is set, the Drying cycle will
start every day at the same time until the setting is
modified.
Use the arrows or or the key to return to
the basic Massage screen.
NOTE: The time format is preset as follows:
French: 24 hour
English: 12 hour (AM and PM)
Spanish: 24 hour
MIAPLUS®- USER GUIDE