Bakker Elkhuizen WORK & MOVE Desk User manual

Work Smart - Feel Good
WORK & MOVE Desk
Installation guide
www.bakkerelkhuizen.com

Work Smart - Feel Good
A. Cantilever (2x)
B. Columns (2x)
C. Beam
D. Feet (2x)
E. Wireless Bluetooth
controller
F. Manual controller
G. WORK & MOVE
connector
H. Power cable
I. Tabletop
K. Caps with screws
for the columns
J. Screws:
- 22x Mounting
screws (20 + 2 extra)
- 2x Mounting screws
for the desk panel
- 3x Cable clamps
- 8x M6 screws for
mounting the
feet on columns.
1.
A
B
F
G
H
D
C
J
I
Parts:
E
K

Work Smart - Feel Good
2.
3.
Extend beam to required length
(width 1150 to 1750 mm), adjustable in 50 mm steps.
Make sure, when placing the beam on the tabletop, that the RJ45 socket
is on the same side as the drill holes for the desk controller.
Turn tabletop upside down with the drill holes facing up.
The beam must not be pulled completely apart
to make sure the drive shaft is not pulled apart.
Minimum adjustment in the connection end is 100 mm
(to keep power and RJ45 (data cable) sockets accessible),
otherwise adjustable in 50 mm steps.

Work Smart - Feel Good
4.
Click!
5.
Mount cantilever on the end of both sides of the beam.
Make sure that the cantilevers are placed correctly and
cannot be twisted o the beam.
Do not extract the beam using the cantilevers as handles.
Place a cantilever slightly tilted at end of beam.
Press cantilever into place until a click is heard and
pawls lock cantilever in correct position.
Place assembled frame in correct position.
Make sure that the drill holes match the holes in the beam & cantilevers.
4.3
4.1
4.2
Beam
Cantilever

Work Smart - Feel Good
6.
Fasten frame to tabletop using 20 mounting screws as follows
(lining up with drill holes):
A. 8 screws at ends of beam. Use one of these to x mains cable to beam
with cable clamp creating a cable relief, see step 9.
B. 4 screws at extension points.
C. 8 screws in cantilevers.
AA B
CC
C C
Beam
Cantilever

Work Smart - Feel Good
7.2
7.3
7.
Click!
Mount columns.
Ensure columns
are completely
retracted.
If the column extracts when turned upside down,
press by hand to completely retracted position.
Tilt columns and
place correctly
on beam using
guiding notches.
Fix column to beam by pressing down until a “click”
is heard and both pawls lock column in correct position.
Check that both pawls are visible after mounting of the columns.
Otherwise, remove column and try again.
7.1

Work Smart - Feel Good
8.
9.
Mount manual controller
or the WORK & MOVE cable.
Connect power cable.
Ensure that only one
manual controller is
connected to the beam
at the same time.*
Ensure to make a cable
relief using the cable
clamp when fastening the
cable to the tabletop.
Inside the
RJ45 socket
* If this is connected you can put the orange WORK & MOVE cable into the RJ45
socket so you can operate the table with the WORK & MOVE software that’s
installed on your laptop. If you don’t want to use the WORK & MOVE software, you
still can use the Linak manual controller to alternate between sitting and standing.

Work Smart - Feel Good
10.
Mount feet on columns using
eight M6 mounting screws.
10.1
Mount feet.

Work Smart - Feel Good
11.
10.2
Mount adjustment screws.
12.
Turn the WORK and MOVe desk around on his feet and make sure that
it’s level. If necessary, level out the table with the adjustment screws (see
10.2).
Connect the WORK & MOVE desk to the power outlet and check that both
the manual and WORK & MOVE controllers are working.
Your desk is now ready for use.
If you want to use the desk with the WORK & MOVE cable you will need to
install the software on your laptop.

Work Smart - Feel Good
Notes: