BALCO AU200016 User manual

Motorcycle
Bluetooth Kit
Instruction Manual
Model: AU200016
Version 1.0

21300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitSafety Instructions
Read this manual thoroughly before irst use and keep it in a safe place for
future reference, along with the warranty card, purchase receipt and caron.
The safety precautions enclosed here in reduce the risk of ire, electric shock
and injury when correctly adhered to. Follow all instructions and take notice of
all warnings to reduce the risk of ire or electric shock.
• Do not remove the cover or the back of this product. There are no user-
serviceable pars inside this product.
• Do not repair the unit yourself. Only have it serviced by qualiied personnel.
Supervise young children to ensure they do not play with the product.
• Do not submerge the product in liquids.
• Do not place the product near other items that may damage it, such as
naked lame sources (lit candles) or excessive heat (bar radiator).
• Do not place near strong magnets or strong electric currents.
• Do not expose to chemicals, oils, or other liquids.
• Do not drop or jar the product. Dropping or rough use of the unit will
cause damage.
• Do not attempt to open the product housing. There are no user-
serviceable pars inside this product.
• Dispose of the product according to local standards and regulations
• When you disconnect the power cord or any enhancement, grasp and pull
the plug, not the cord. Never use a charger that is damaged
• Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type
• Battery shall not be exposed to excessive heat such as sunshine, ire or
the like
• Attention should be drawn to the environmental aspects of battery
disposal

3
1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitSafety Instructions
WARNING: Using headphones while operating a motorcycle, motor
vehicle, watercra or bicycle can be dangerous. Use caution while using
your Motorcycle Bluetooth® Kit when you are engaging in any activity
that requires your full attention.
This product has been tested according to AS/NZS CISPR 32:2015, AS/NZS
4268:2017 and AS/NZS 60065:2018

41300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitContents
Safety Instructions 2
Contents 4
Pars List 6
Product Overview 6
Technical Speciications 7
Setup 8
Fitting the Bluetooth receiver to you helmet 8
Charging the Bluetooth reciever 9
Powering on and of 10
Operation 11
Operating with a Bluetooth enabled mobile 11
Pairing 11
Phone calls 11
Operating with a Bluetooth enabled audio device 12
Playing music 12
Answering a call while listening to music 12
Voice assistant 12
The multifunction button 13
Operating the camera 13
Star video recording 13
Taking photos 14
Turning of the camera 14
Viewing videos and photos on your phone 14
Synchronising time with your phone 14

5
1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth Kit
Operating via intercom 14
Pairing one Balco Motorcycle Bluetooth® receiver to another 14
Staring a conversation via the intercom 15
Ending a conversation via the intercom 15
Pairing multiple Bluetooth receivers via the intercom 16
Speaking in a group 17
Operating with a walkie-talkie 17
Maintenance, Storage & Disposal 18
Troubleshooting 19

61300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitPars List
Product Overview
1. 1 x Motorcycle Bluetooth® receiver
2. 1 x Microphone speaker
3. 1 x Clip
4. 1 x Allen key
5. 1 x PTT VELCRO tape
6. 4 x Headphone Velcro
7. 1 x USB Cable
8. 1 x Walkie-talkie PPT control cable
9. 1 x Manual
10. 1 x Warranty card
3
2
4
5
1
7
8
9 10 11
6
1. Antenna
2. WiFi button
3. Camera button
4. Recording indicator
5. Bluetooth indicator
6. Jog wheel
7. Multifunction button
8. Earphone jack
9. Memory card slot
10. Reset button
11. Walkie-talkie jack

7
1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitTechnical Speciications
• Frequency: 2.4GHz
• Suppors: A2DP and AVRCP
• Suppored Bluetooth Proiles: Bluetooth Headset and Hands free
• Camera Resolution: 1080P
• Input rating: 5V d.c. 1A
• Operating Range: Up to 10m for cell phones: up to 500 meters for
intercom function
• Suppor 6 people connection
• Weight: 77grams (excluding accessories)
• Size: 98mm(L) x 58mm(W) x 30mm(H)
• Battery type: Rechargeable Lithium Polymer 1500mAh
• Stand by: Up to 300 hours
• Working Time:
• Video recording: 4.5hours
• Phone: Up to 30 hours
• Intercom: Up to 7 hours
• Charging Time: 3 hours
• Headset: High Power ultra slim speaker with integrated boom
• IP Rating: IP65
• Bluetooth Version: 2.1

81300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth Kit
Fitting the Bluetooth receiver to you helmet
1. Open the TF card Slot as shown to the right
and inser the memory card (can suppor a
max of 64G TF card).
2. Using the Allen key provided, loosen the
Headset Clip screws.
3. Slide the Headset Clip onto the le side of
the helmet (when on your head). Take care
to place the inside of the Headset Clip under
the helmet padding.
4. Adjust the clip until you ind the best
location for your helmet. Ensure that the slots in the Headset Clip mount
are facing away from the helmet.
5. Tighten the screws to hold the clip irmly
in place.
Note: Take care not to over tightening the screw as
this can break the clip.
6. Slide the Bluetooth receiver down into the
slots on the headset clip. Make sure that this
is securely locked in.
7. To attach the ear speaker & microphone
headset, test which par of the helmet will
be the best location by putting your helmet on and locating the place
closest to your ears. You will need to put the helmet on a few times to
ind the optimum position to apply the pad. When the correct position is
found, remove
the adhesive
protective strip,
and apply to the
felt adhesive
earphone pad.
Setup

9
1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitSetup
8. Attach ear speaker to the felt adhesive earphone pad. Run the microphone
arm along the inside wall of the helmet, to where your mouth will be. The
microphone arm is lexible and should be adjusted so it sits in the best
position in front of your mouth. Some helmets have removable padding; if
yours does, it is recommended to run the speaker and microphone under
the padding.
9. Connect the
headset to the
Bluetooth®
receiver. The
plug can only be
insered in one
orientation.
10. Secure the cord of
the headset plug
inside the helmet. Tuck any extra wire into the helmet. Ensure that only a
few centimetres of the cord comes out.
You have successfully mounted the Motorcycle Bluetooth Kit.
Charging the Bluetooth reciever
Before using the device fully charge the battery, this will take about 3 hours.
1. Inser the USB-C charging cable into the charging por on the headset.
Inser the other end of the charging cable into either a power adaptor or
your computer’s USB por.
2. When charging, the LED light will be a sold red colour. When the battery is
fully charged the red light with turn of.
3. When the battery is fully charged and the bluetooth is connected a blue
LED light will lash.

10 1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth Kit
Powering on and of
1. To turn the device ON, press the multifunction button for 3 seconds until
you hear a voice prompt: ‘Power on’ then release the button.
2. To turn the device OFF, press the multifunction button for about 8 seconds
until you hear a voice prompt: ‘Power o’ then release the button.
Setup

11
1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth Kit
Operating with a Bluetooth enabled mobile
Pairing
1. Place your Bluetooth enabled phone and the Bluetooth receiver near each
other (within 1 meter).
2. Make sure the Motorcycle Bluetooth is turned of.
3. In shutdown state, hold the Multifunction button down for 6 seconds until
you hear the voice prompt: ‘Pairing’ then release the button, the indicator
LED will lash red and blue.
4. Activate Bluetooth on your mobile phone and search for the Bluetooth
receiver (Refer to your phones instruction if you are unclear on how to
search for a Bluetooth device).
5. Choose the Bluetooth device named Balco Motorcycle Bluetooth and
choose to pair this device.
6. The indicator LED will change to blue and you will hear a voice prompt
‘Connected’.
Phone calls
Answering incoming calls
1. Press the multifunction button once to answer the incoming call you
will hear a voice prompt “Call answered”. (The call will be automatically
answered aer 10 seconds if no action is taken)
2. Use the jog wheel to increase or decrease the volume of the headset.
Ending phone calls
Press the multifunction button once to end the call you will hear a voice
prompt: ‘Call terminated’.
Rejecting phone calls
Hold down the multifunction button for 2 seconds, then release your hand
when you hear a voice prompt: ‘Call rejected’.
Operation

12 1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitOperation
Operating with a Bluetooth enabled audio device
Playing music
1. Select music to play directly from your audio device (check your audio
device or phone instructions for how to do this).
2. Play music through the headset press the multifunction button once.
3. Pause music press the multi-function button again.
4. Skip songs forward by quickly turning the jog wheel in a clockwise
direction.
5. Skip songs backwards by quickly turning the jog wheel in an anti-clockwise
direction.
6. Volume up by turning the jog wheel clockwise and holding until the volume
is at the right level.
7. Volume down by turning the jog wheel anti clockwise and holding until the
volume is at the right level. You will hear a long beep if the volume is at the
highest or lowest level.
Answering a call while listening to music
Calls will automatically come through the headset while music is playing.
1. To answer a call, press the Multifunction button once.
2. To reject a call, hold the multifunction button down until you hear a beep
Music will pause for the call duration and resume automatically once the call
has ended.
Voice assistant
To activate voice assistant (or to inish using the voice assistant function on
your phone): press and hold the multifunction button for 2 seconds (your
phone must be compatible with voice assistant ).

13
1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitOperation
The multifunction button
Music/ FM control: if there is no pairing, double click the multifunction button
to switch to FM then click the multifunction button and switch to music mode.
Note: If you have paired your motorcycle Bluetooth with another rider you will have to
disconnect the intercom, then reconnect your Bluetooth receiver and phone and click
the multifunction button. Double click the multifunction button to switch between
music mode.
FM station selection: Turn the jog wheel clockwise to the next FM channel,
and anti-clockwise to the previous one.
Volume control: Turn the jog wheel clockwise to the end and hold until the
volume reaches your desired level. When the volume meets maximum level you
will hear a tone. To reduce the sound turn the jog wheel anti-clockwise and
hold until the volume reaches the desired level. When the volume reaches the
lowest level you will hear a tone.
Note: This is the same for when using the intercom or listening to music
Next song: Turn the jog wheel clockwise to skip ahead or anticlockwise to hear
the previous song.
Operating the camera
Star video recording
1. Hold down the key for 5 seconds to turn on camera, press the key
once more to enter video recording mode. You will hear a voice prompt:
‘Video recording’ (each video segment will last 3 minutes)
2. Press again to stop recording, you will hear a voice prompt: ‘Video
recording stopped’
3. When it is recording, the LED will show green (when the TF card is full the
Device will cycle record over the oldest footage irst.)
4. If there is no memory card, you will hear a voice prompt: ‘No TF card’ (will
suppor Max. 64G memory card) video recording or photo function can be
used. Note: TF card is not included.

14 1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth Kit
Taking photos
When you are in video recording mode, press the key to capture an image.
.
Turning of the camera
To turn of the camera hold down the until you hear a tone.
Note: Cancelling the Bluetooth connection will not turn of the camera, you will need to
do this separately.
Viewing videos and photos on your phone
1. Download the GoPlus Cam app on to your mobile phone.
2. Turn on Wi-Fi by holding down the key for 3 seconds, you will hear a
voice prompt: ‘Wi-Fi Turn on’ and the green LED will rapidly lash.
3. Aer turning on the Wi-Fi go into Wi-Fi setting on your phone and choose
the “Balco Motorcycle Bluetooth” Wi-Fi name to connect. If it requires a
password, please enter “12345678” and conirm to continue.
4. Open the GoPlus cam app on your phone and view the videos and photos.
Note: You can also view the saved videos or photos on your computer via the TF card.
Synchronising time with your phone
1. Open the GoPlus Cam icon on your phone to open the app.
Note: Your phone must be connected to WIFI to complete this.
2. Click the version number on the button le corner.
3. Click “set the WIFI spor cam time” option, then chose “enable”.
Operating via intercom
Pairing one Balco Motorcycle Bluetooth® receiver to another
1. Turn OFF both Balco Motorcycle Bluetooth receivers.
2. Place both receivers within a 1m visible range of each other.
3. Press and hold the Multifunction button on both receivers for 10 seconds
until you hear a voice prompt: ‘Paring’. The LED indicator will lash blue and
red alternatively.
Operation

15
1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth Kit
4. Quickly press the multifunction button on one of the receivers (we will call
this receiver A) and it will star searching for the other receiver (receiver
B) so they can be paired
5. You will hear a voice prompt ‘Intercom connected’. When they have been
successfully paired the red and blue LED will change to a lashing blue only
light.
Note: If either of the receivers do not have a lashing blue and red LED, clear the
previous intercom connections, see step 1 on page 16 of this manual and then repeat
above steps.
Staring a conversation via the intercom
Once the two receivers are paired, simply begin talking. Use the jog wheel to
increase or decrease the volume.
Ending a conversation via the intercom
Press the multifunction button on either receiver to end the conversation you.
will hear a voice prompt ‘Intercom disconnected’.
Operation

16 1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth Kit
Pairing multiple Bluetooth receivers via the intercom
You can have up to 6 Motorcycle Bluetooth receivers connected at one time.
1. To clear any previous intercom connections. Press and hold the
Multifunction button of both Balco Motorcycle Bluetooth receivers for
8 seconds until you hear a voice prompt: ‘O’ then hold the button for
another 3 seconds until you hear a double beep.
2. “A” connects with “B: and shutdown B aer pairing.
Note: You will need to shut down without clearing the intercom connection to each last
paired device.
3. Connect B to C and shutdown C aer pairing.
4. C connects with D and shutdown D aer pairing.
5. D connects with E and shutdown E aer pairing.
6. E connects with F.
Connect A, B, C, D, E, F in tandem arrangement
1. Press the Multifunction button of D to connect to E, you will hear an
intercom prompt voice.
2. Press the Multifunction button of C to connect to D, you will hear an
intercom prompt voice.
3. Press the Multifunction button of B to connect to C, you will hear an
intercom prompt voice.
Operation

17
1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth Kit
4. Press the Multifunction button of A to connect to B, you will hear an
intercom prompt voice.
Now A, B, C, D, E, F are successfully connected, and you can use group talk.
Speaking in a group
Once all the Bluetooth receivers are connected you can star talking to all
riders at the same time. See staring a conversation via the intercom on page
15 for instructions.
Operating with a walkie-talkie
1. Connect the Bluetooth receiver to the walkie-talkie with the PPT control
line.
2. Bind the PPT Velcro tape to the handlebar of your motorbike.
3. Stick the PTT button to the Velcro tape.
4. Place the walkie-talkie in a suitable place so you can use the walkie-talkie
while you are riding.
Note: When connected to multiple devices the functions will work in the following
priority order: Phone calls > PPT intercom > Bluetooth music/GPS/Voice reminder.
Operation

18 1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitMaintenance, Storage & Disposal
The Motorcycle Bluetooth Kit does not require scheduled maintenance or
cleaning. Should cleaning be necessary, simply wipe the outside surace with a
dry so cloth. Be sure to unplug this device before cleaning.
Always store your device in a clean dry environment and avoid storage in
extreme heat or cold.
At the end of its working life, do not throw this product out with your
household rubbish. Electrical and electronic products contain substances that
can have a detrimental efect on the environment and human health if disposed
of inappropriately. Observe any local regulations regarding the disposal
of electrical consumer goods and dispose of it appropriately for recycling.
Contact your local authorities for advice on recycling facilities in your area.
Observe and local regulations regarding the disposal of waste products.
Contact your local authorities for advise on recycling facilities in your area.
Please keep the original packaging caron and materials in a safe place. It will
help to prevent any damage if the product needs to be transpored in the
future. In the event it is to be disposed of, please recycle all packaging material
where possible.
If you require another copy of this instruction manual, please contact
[e-mail] to obtain an electronic copy.

19
1300 663 907
Aer Sales Suppor
[e-mail]
www.balcobrands.com Model number: AU200016
Motorcycle Bluetooth KitTroubleshooting
Bluetooth cannot be turned on
If the Bluetooth cannot be turned on but the Bluetooth receiver can be
turned in, it is usually because the Bluetooth was not successfully reset aer
a shutdown. Please press and hold the reset button for 5 seconds to rest the
Bluetooth and then try to turn on the Bluetooth again.
Bluetooth receiver can not be turned on
If the Bluetooth receiver can not be turned on even though the battery
has enough charge, it is usually because the Bluetooth receiver was not
successfully reset aer the last shut down. Please press and hold the reset
button for 2 seconds to reset the Bluetooth and then try to turn on the
Bluetooth again.
The music freezes when I open the app to view the video
When opening the App to view the video, due to the size of the video stream, it
will interere with the Bluetooth. The Bluetooth needs to be temporarily turned
of and should only be turned on aer exiting the app .
There is crackling noise when playing video on my mobile
Wi-Fi needs to be turned of aer the video has been downloaded and is played
for the irst time. Doing this should prevent any crackling noise.
I cannot hear music/incoming calls
Check the volume on the Bluetooth receiver. Setting your phone or audio
device to maximum volume usually resolves this issue.