B&B Electronics iMcV-LIM 10/100 User manual

iMcV-LIM 10/100
Operation Manual
ii
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B
limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B
prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Limited Lifetime Warranty
Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B Electronics warrants that each such
product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is applicable
solely to the original user and is not transferable.
This warranty is expressly conditioned upon proper storage, installation, connection, operation and maintenance of
products in accordance with their written specifications.
Pursuant to the warranty, within the warranty period, B&B Electronics, at its option will:
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B&B Electronics are not subject to any warranty or indemnity offered by B&B
Electronics, but may be subject to the warranties of the other manufacturers.
Notwithstanding the foregoing, under no circumstances shall B&B Electronics have any warranty obligations or any other
liability for: (i) any defects resulting from wear and tear, accident, improper use by the buyer or use by any third party
except in accordance with the written instructions or advice of the B&B Electronics or the manufacturer of the products,
including without limitation surge and overvoltage conditions that exceed specified ratings, (ii) any products which have
been adjusted, modified or repaired by any party other than B&B Electronics or (iii) any descriptions, illustrations, figures
as to performance, drawings and particulars of weights and dimensions contained in the B&B Electronics’ catalogs, price
lists, marketing materials or elsewhere since they are merely intended to represent a general idea of the products and do
not form part of this price quote and do not constitute a warranty of any kind, whether express or implied, as to any of the
B&B Electronics’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE EXPRESS WARRANTY SET
FORTH ABOVE IS B&B ELECTRONIC’ SOLE OBLIGATION UNDER THIS WARRANTY. THE WARRANTY CONTAINED
IN THIS SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS ARE DO NOT INFRINGE OR VIOLATE THE
INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B ELECTRONICS BE LIABLE FOR
LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS, LOST PROFITS OR GOODWILL OR
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES. B&B ELECTRONIC SHALL
DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR INDEMNITIES MADE BY ANY
OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF
B&B ELECTRONIC WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.

iii
Table of Contents
FCC Radio Frequency Interference Statement ....................................................ii 
Limited Lifetime Warranty..................................................................................ii 
About the iMcV-LIM 10/100 ..............................................................................1 
Configuration Instructions ..................................................................................1 
Installing an iMcV-LIM 10/100 ...........................................................................2 
Unmanaged Modules.........................................................................................2 
Modes of Operation...........................................................................................3 
Troubleshooting Features ...................................................................................4 
Link Fault Detection in FORCE Modes (LFD)......................................................5 
LED Operation...................................................................................................6 
Troubleshooting Features ...................................................................................7 
Specifications .....................................................................................................8 
B&B Electronics Technical Support.....................................................................9 
Fiber Optic Cleaning Guidelines.......................................................................10 
Electrostatic Discharge Precautions...................................................................11 
Certifications....................................................................................................12 
1
About the iMcV-LIM 10/100
The iMcV-LIM 10/100 is an SNMP-manageable, IEEE 802.3 single-conversion media
conversion module which converts between:
 10Base-T twisted pair and 10Base-FL multi-mode or single-mode fiber, or
 100Base-TX twisted pair and 100Base-SX multi-mode fiber, 100Base-FX single-
mode fiber or single-strand single-mode fiber.
The iMcV-LIM requires one slot in an SNMP-manageable chassis or an unmanaged
chassis from B&B Electronics. The iMcV-LIM features one RJ-45 connector and one
pair of ST or SC fiber connectors.
Configuration Instructions
In many networks, the media converter is typically installed as a pair, between two
copper-based end devices. The iMcV-LIM 10/100 can also be installed as a single
media converter, between one copper-based device and the other a fiber-based
device. However, when connected to certain fiber-based devices, there may be
difficulty in the installation: if a link partner that is connected to the iMcV-LIM 10/100
media converter is powered down on the copper port, noise on the copper segment
may be detected and transferred to the fiber line. A result of the noise will generate
errors that look like CRC errors. Some fiber-based devices many detect this noise and
disable the fiber segment.

2
Installing an iMcV-LIM 10/100
The iMcV Modules install in B&B Electronics’ SNMP manageable iMediaChassis series
or in any MediaChassis.
NOTE
All modules are hot-swappable.
To install an iMcV Modules:
1.
Remove the blank bracket covering the slot where the module is to be installed
by removing the screws on the outside edges of the bracket.
2.
Slide the iMcV Modules into the chassis, via the cardguides, until the module is
seated securely in the connector.
3.
Secure the module to the chassis by tightening the captive screw.
4.
Save any “blanks” removed during installation for future use if the configuration
requirements change.
Managed Modules
To manage one or more iMcV-LIM 10/100, an SNMP agent must be present in the
chassis. To configure Managed Modules, install the module first, and then configure
using the management software. If using management software, software will
override hardware DIP Switch settings.
Unmanaged Modules
Before installing, configure the iMcV-LIM 10/100modules for desired features. Refer
to table which indicates the available features and settings for the iMcV-LIM 10/100
modules.
Dip
Switch
Feature Function Default
S1 LFD Link fault detection available in forced mode only
(S3 is ON)
OFF
S2 PNP
(AN)
Auto Negotiation mode (plug-n-play) available when
forced mode is disabled (S3 is OFF)
ON
S3 Force Force mode forces the module to operate at 10 or
100 Mbps as determined by S4
OFF
S4 10/100 When ON, operates at 10 Mbps.
When OFF, operates at 100 Mbps.
Available when forced mode is enabled (S3 is ON)
OFF
Remaining DIP Switches are factory configured—DO NOT CHANGE
3
Modes of Operation
The iMcV-LIM 10/100 has four modes of operation:
 PNP (Auto Negotiation)
 FORCE 10Mbps
 FORCE 100Mbps
 Selective Advertising AN (All OFF)
NOTE
The iMcV-LIM 10/100 cannot be set for Half- or Full-Duplex manually. Duplex is determined
by the link partners connected to the iMcV-LIM 10/100.
The iMcV-LIM 10/100 media converter is typically installed in pairs and provides
compatibility with legacy 10BASE-FL devices, while also providing support for
100Mbps devices. This is a PHY based device to allow very low propagation delays
but in turn the speed and duplex of both its copper and fiber ports must be the same.
For the iMcV-LIM 10/100 to function properly, the copper port must have link before
the fiber port will link up.
In a back to back configuration, both units must have the Plug-N-Play
PNP (AN)
switch set to ON for the copper ports to auto negotiate from end to end. In this
mode the fiber link becomes transparent allowing the units at both ends of the link to
function as if they were connected over one copper line. All auto negotiation
signaling is the result of signaling received on the ports of the unit. Only use this
mode with two iMcV-LIM 10/100 media converters installed as a pair.
With all switches set to OFF
, the unit sends its own Selective Advertising (AN)
signaling on the copper port. This advertises both FDX and HDX with the physical
speed that is detected on the fiber line. This signaling cannot occur until this fiber
port is active. If auto negotiation signaling is also received over the fiber from the far
end equipment, the auto negotiation signaling on the copper port will include this
information.
In all of the
FORCE modes , no auto negotiation signals are sent or acted on. The unit
will blindly send the speed assigned and supports either FDX or HDX data. The LFD
function is only available in the FORCE modes.

4
Selective Advertising is a mode in which the speed and duplex for the copper and the
fiber are specifically advertised. This mode is available when DSW 1-4 are set to OFF.
Troubleshooting Features
The iMcV-LIM 10/100 media converters include two advanced troubleshooting
features to help locate “silent failures” on the network.
 Transparency
 Link Fault Detection (LFD)
Transparency
Transparency is only available in PNP mode. Transparency treats the connection
between the two end devices as if there were no media converters installed. In a
typical application where two media converters are installed between two copper-
based switches, the twisted pair cables as well as the fiber cable are seen as one
entity. If a fault occurs on any segment between the two end devices, link LEDs on
the end devices will go out. This prevents any failure on the link between the end
units from going undetected.
As stated, transparency is available when iMcV-LIM 10/100 is operating in PNP (AN)
mode:
 S2 PNP (AN) must be ON
 S1 (LFD), S3 (Force) and S4 (10 or 100) must be OFF
Dip
Switch
Feature Selective
Advertising
PNP
(AN)
Force
100
Force
10
Force
100 LFD
Force
10 LFD
S1 LFD OFF OFF OFF OFF ON ON
S2 PNP (AN) OFF ON OFF OFF OFF OFF
S3 FORCE OFF OFF ON ON ON ON
S4 10/100 OFF OFF OFF ON OFF ON
5
Link Fault Detection in FORCE Modes (LFD)
Link Fault Detection (LFD) is only available when using Force 10 or Force 100 mode
and provides the same information as link fault pass through as does in PNP mode to
detect silent failures. When LFD is enabled and the input link is down at one
interface to the iMcV-LIM 10/100, the transmitter output on that interface is turned
off for about 425ms every 3.8 seconds (i.e., blinking). It applies to both network
interfaces and to both data rates. If the link at the other interface to the iMcV-LIM
10/100 is also down, there is no output. LFD causes the Link Up indicator of the link
partner to blink.
When the iMcV-LIM 10/100 is in one of the FORCE modes, enable LFD by setting S1
to the ON position.
In order for LFD to function properly, Force mode must be enabled by setting:
 S3 to ON with either S4 ON for 10 Mbps or S4 OFF for 100 Mbps
 S2 must also be OFF
NOTE
When using the LFD feature, if the DIP Switches are in any other combination than listed
above, the iMcV-LIM 10/100 may exhibit erratic behavior.

6
LED Operation
The iMcV-LIM 10/100 features several standard and diagnostic LEDs per port.
LNK
ACT
100
LFD
PNP
(AN)
PWR
100
ACT
LNK
Twisted Pair Port
Glows green when a twisted pair link is established.
Glows yellow when data is detected on the port.
Glows yellow when 100 Mbps data is detected on the
port.
Glows green when Link Fault Detection is enabled.
Glows green when Auto Negotiation mode is enabled
(transparency).
Glows green when unit has power.
Fiber Port
Glows yellow when 100 Mbps data is detected on the
port.
Glows green when data is detected on the port.
Glows green when a fiber link is established.
NOTE
Before either LNK LED will glow solid, the twisted pair and fiber optic cables must be
connected and the twisted pair crossover/ pass-through switch set correctly.
7
Troubleshooting Features
The 10/100 Autosensing Modules includes two advanced troubleshooting features,
Transparency and Link Fault Detection, to help locate “silent failures” on the
network.
Transparency
Transparency is only available when using AN. When the 10/100 Autosensing
Modules is Auto Negotiating, transparency treats the connection between the two
end devices as if there were no media converters installed. For example, in a typical
application where two media converters are installed between two copper-based
switches the twisted pair cables as well as the fiber cable are seen as “one” entity. If a
fault occurs on any segment between the two end devices, link LEDs on the end
devices will go out.
Since transparency is only available when the 10/100 Autosensing Modules is
operating in Auto Negotiation mode, S2 (AN) must be ON and S1 (LFD), S3 (Force)
and S4 (10/100) must be OFF.
Link Fault Detection
Link Fault Detection (LFD) is only available when using Force 10 or Force 100 mode.
When LFD is enabled and the input link is down at one interface to the 10/100
Autosensing Modules, the LFD LED will blink. This applies to both network interfaces
and to both data rates. If the link at the other interface to the 10/100 Autosensing
Modules 10/100 is also down, there is no output and LFD causes the Link LED to
blink.
When the 10/100 Autosensing Modules is in one of the Force modes, enable LFD by
setting S1 to the ON position. In order for LFD to function properly, Force mode
must be enabled by setting S3 to ON with S4 set for the proper speed.
Twisted Pair Crossover/Pass-Through Switch
The iMcV-LIM 10/100 features a crossover/pass-through push-button switch, located
on the faceplate next to the RJ-45 connector, to set the twisted pair connection type.
Select a pass-through connection by pressing the push-button IN. A crossover
connection is selected when the push-button is OUT. If it is not clear which
connection is needed, set the push-button to whatever setting makes the twisted pair
LNK LED glow.

8
Specifications
Operating Temperature
+
32°F to +122°F (0°C to +50°C)
Storage Temperature
-4°F to 158°F (-20°C to +70°C)
Humidity
5 - 95% (non-condensing)
Power Consumption (typical)
650 mA max. @ 5 VDC
For fiber optic specifications, visit the B&B Electronics Web site.
9
B&B Electronics Technical Support
Tel: [phone] (in the U.S. and Canada)
Monday-Friday, 7:00am-7”00pm CST
[phone] (Europe)
Monday through Friday 8:00am - 5:00pm GMT
Fax: [phone] U.S. and Canada
[phone]S5 Europe
E-Mail: [email protected] U.S. and Canada
[email protected] Europe
Web: www.bb-elec.com

10
Fiber Optic Cleaning Guidelines
Fiber Optic transmitters and receivers are extremely susceptible to contamination by
particles of dirt or dust, which can obstruct the optic path and cause performance
degradation. Good system performance requires clean optics and connector ferrules.
1.
Use fiber patch cords (or connectors, if you terminate your own fiber) only from
a reputable supplier; low-quality components can cause many hard-to-diagnose
problems in an installation.
2.
Dust caps are installed at B&B Electronics to ensure factory-clean optical devices.
These protective caps should not be removed until the moment of connecting
the fiber cable to the device. Should it be necessary to disconnect the fiber
device, reinstall the protective dust caps.
3.
Store spare caps in a dust-free environment such as a sealed plastic bag or box so
that when reinstalled they do not introduce any contamination to the optics.
4.
If you suspect that the optics have been contaminated, alternate between
blasting with clean, dry, compressed air and flushing with methanol to remove
particles of dirt.
11
Electrostatic Discharge Precautions
Electrostatic discharge (ESD) can cause damage to any product, add-in modules or
stand alone units, containing electronic components. Always observe the following
precautions when installing or handling these kinds of products
1.
Do not remove unit from its protective packaging until ready to install.
2.
Wear an ESD wrist grounding strap before handling any module or component.
If the wrist strap is not available, maintain grounded contact with the system unit
throughout any procedure requiring ESD protection.
3.
Hold the units by the edges; do not touch the electronic components or gold
connectors.
4.
After removal, always place the boards on a grounded, static-free surface, ESD
pad or in a proper ESD bag. Do not slide the modules or stand alone units over
any surface.
WARNING! Integrated circuits and fiber optic components are
extremely susceptible to electrostatic discharge damage. Do not
handle these components directly unless you are a qualified service
technician and use tools and techniques that conform to accepted
industry practices.

12
Certifications
CE: The products described herein comply with the Council Directive on
Electromagnetic Compatibility (2004/108/EC). For further details, contact B&B
Electronics.
European Directive 2002/96/EC (WEEE) requires that any equipment that bears this
symbol on product or packaging must not be disposed of with unsorted municipal
waste. This symbol indicates that the equipment should be disposed of separately
from regular household waste. It is the consumer’s responsibility to dispose of this
and all equipment so marked through designated collection facilities appointed by
government or local authorities. Following these steps through proper disposal and
recycling will help prevent potential negative consequences to the environment and
human health. For more detailed information about proper disposal, please contact
local authorities, waste disposal services, or the point of purchase for this equipment.
Class 1 Laser product, Luokan 1 Laserlaite,
Laser Klasse 1, Appareil A’Laser de Classe 1
International Headquarters
B&B Electronics
707 Dayton Road
Ottawa, IL 61350 USA
Phone [phone] — General Fax [phone]
Email: [email protected]m
Website: www.bb-elec.com
European Headquarters
B&B Electronics
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone [phone] — Fax [phone]S5
Email: [e-mail]
Website: www.bb-elec.com
© 2013 B&B Electronics. All rights reserved.
The information in this document is subject to change without notice. B&B Electronics assumes no responsibility for any
errors that may appear in this document. iMcV-LIM 10/100 is a trademark of B&B Electronics. Other brands or product
names may be trademarks and are the property of their respective companies.
Document Number 50-80216-01 B6 October 2013