Bang & Olufsen BeoCom 1401 User manual

BeoCom 1401
RINGING SIGNAL
BeoCom 1401 has 10 different settings
of the ringing signal, combined from 3
levels and 3 melodies, and the tone
ringer disconnected.
SETTING THE RINGING SIGNAL
Press Enter
Press
Press 0-9 to select the setting of your
choice.
Press Enter
When the ringing signal is disconnected
(setting 0), it is automatically reconnected
the first time you lift off the handset and
place it in the base again.
ADJUSTING THE VOLUME
During a call, you can adjust the
handset volume in 5 steps by pressing
the +and –buttons. All calls start at
the medium volume level.
Press +to increase the volume.
Press –to decrease the volume.
REDIALING
Press Rdl to call the last number
called.
Telephone numbers exceeding 31 digits
cannot be redialed.
In order to ensure that the last number
is stored and can be redialed, the
handset must be placed in the base (or
press the switch off key on the lower
side of the handset) for at least 1
second.
MICROPHONE
Press to mute the microphone.
A beep signal in the handset indicates
that the microphone is muted.
Press to connect the microphone.
Please note! Pressing other keys one
or two times will connect the micro-
phone as well.
MEMORY
BeoCom 1401 memorizes 10 tele-
phone numbers which can be stored
under the code numbers from 0 to 9.
Numbers of up to 21 digits can be
memorized.
PLEASE NOTE!
If the telephone is disconnected from
the line for more than 1 hour,
numbers stored in the memory may
be erased. This may also happen
when using a computer modem or
another telephone on the same line.
STORING PHONE NUMBERS
Press Enter
Press Mem
Enter the code number (0-9)
Enter the phone number
Press Enter
DIALING A STORED NUMBER
Press Mem
Enter the code number (0-9)
DELETING A STORED NUMBER
A stored number is deleted by storing
a new number under the same code
number.
WALL HOLDER
The package contains a wall holder
that consists of one faceplate which
holds the handset and a choice of
two backplates which attach to the
wall.
The wider backplate is designed to fit
over the wall phone jack. It will slide
down and snap into place over the
pegs on the wall phone jack.
There are tabs inside this backplate
that allow for excess cord to be
wrapped inside the backplate. If you
wrap the cord clockwise then lead
the cord out in the bottom left
channel of the holder and if you
wrap the cord counterclockwise, then
lead the cord out in the bottom right
channel.
The faceplate will then slide down
and lock into place over the clips on
the backplate.
The narrow backplate is designed to
be screwed into the wall if no wall
phone jack is available. Please see the
enclosed instructions for details.
Beocom
Beocom
2
5
8
0
Vol
3
6
9
Mem
Enter
ABC DEF
GHI
PQRS
JKL
TUV
MNO
WXYZ
1
4
R
Rdl
Vol
7
Flash
Slow
Normal
Fast
Disconnected
Low
1
4
7
0
Medium
2
5
8
High
3
6
9

ACCESSORIES
THE TABLE BASE
The table base has 4 rubber feet. Each
foot can be tipped up which allows
the cord to be led out in the direction
of your choice.
The cover plate can be tilted to rest
on the tabletop. Under the cover
plate there is a note pad and a
directory for your stored phone
numbers.
PLACEMENT AND CLEANING
Do not place the telephone in very
dusty or dirty surroundings. Do not
expose it to excessive moisture.
Clean the telephone with a soft,
damp cloth dipped in water mixed
with a few drops of mild detergent.
TECHNICAL SPECIFICATIONS
Power supply from the telephone
network
Ambient temperatures -25oC - +55oC
Relative humidity 15% - 95%
Visit our website on:
www.bang-olufsen.com
3500727 0301 Version 1.0
INDUSTRY CANADA WARNINGS
Notice:
The Industry Canada Label identifies certified
equipment. This certification means that the
equipment meets telecommunications
network protective, operational and safety
requirements as prescribed in the
appropriate Terminal Equipment Technical
Requirements document(s). The Department
does not guarantee the equipment will
operate to the user’s satisfaction.
Before installing this equipment, users
should ensure that it is permissible to be
connected to the facilities of the local
telecommunications company. The
equipment must also be installed using an
acceptable method of connection. The
customer should be aware that compliance
with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be
coordinated by a representative designated
by the supplier. Any repairs or alterations
made by the user to this equipment, or
equipment malfunctions, may give the
telecommunications company cause to
request the user to disconnect the
equipment.
Users should ensure for their own protection
that the electrical ground connections of the
power utility, telephone lines and internal
metallic water pipe system, if present, are
connected together. This precaution may be
particularly important in rural areas.
Caution: Users should not attempt to make
such connections themselves, but should
contact the appropriate electric inspection
authority, or electrician, as appropriate.
Notice: The Ringer Equivalence Number
(REN) assigned to each terminal device
provides an indication of the maximum
number of terminals allowed to be
connected to a telephone interface. The
termination on an interface may consist of
any combination of devices subject only to
the requirement that the sum of the Ringer
Equivalence Number of all the devices does
not exceed 5.
If you have any doubts or questions
concerning the telephone, please do not
hesitate to contact your retailer.
Hearing aid Compatibility:
This telephone
IS HEARING AID COMPATIBLE
BeoCom 1401