Barracuda PUMPS 92000 User manual

SKU: 691-1615
Model # 92000
UNIVERSAL TETHERED FLOAT SWITCH
BA92000 Manual Rev: 6-18
Inventory
1. Universal tethered oat switch (1)
2. Stainless Steel Hose Clamp (1)
3. Mounng Clamp (1)
4. Hardware Pack (2 screws, 2 washers
& 1 stainless steel cord clamp)
LIMITED WARRANTY
Barracuda Pumps warrants the products specied in this warranty to be free from defects in material or workmanship for one (1) year from date of purchase. During the me period and
subject to the terms and condions, the Barracuda Pumps will repair or replace to the original user or consumer any poron of this product which proves to be defecve due to materials
or workmanship. At all mes the Barracuda Pumps shall have and possess the sole right and opon to determine whether to repair or replace defecve equipment, parts, or components.
The Barracuda Pumps has the opon to inspect any product returned under warranty to conrm that the warranty applies before repair or replacement under warranty is approved. This
warranty sets forth the Barracuda Pumps sole obligaon and purchaser’s exclusive remedy for defecve product. Return defecve product to the place of purchase for warranty
consideraon.
WARRANTY PERIOD - PRODUCTS:
If, within the duraon of product use by the original user, this product proves to be defecve due to materials or workmanship, the product shall be repaired or replaced at the Barracuda
Pumps opon, subject to the terms and condions set forth in this warranty statement. Proof of purchase is required for warranty consideraon. In the absence of suitable proof of the
purchase date, the eecve period of this warranty is 12 months from the product’s date of manufacture.
LABOR, ETC. COSTS:
The Barracuda Pumps shall IN NO EVENT be responsible or liable for the cost of eld labor or other charges incurred by any customer in removing and/or axing any product, part, or
component thereof.
PRODUCT IMPROVEMENTS:
The Barracuda Pumps reserves the right to change or improve its products or any porons thereof without being obligated to provide such a change or improvement for units sold and/or
shipped prior to such change or improvement.
GENERAL TERMS AND CONDITIONS:
This warranty shall not apply to damage due to acts of God, normal wear and tear, normal maintenance services and the parts used in connecon with such service, lightning or condions
beyond the control of the Barracuda Pumps, nor shall it apply to products which, in the sole judgment of the Barracuda Pumps, have been subject to negligence, abuse, accident,
misapplicaon, tampering, alteraon; nor due to improper installaon, operaon, maintenance or storage; nor to excess of recommended maximums as set forth in the instrucons.
Warranty will be VOID if any of the following condions are found:
1. Product is used for purposes other than those for which it was designed and manufactured
2. Product not installed in accordance with applicable codes, ordinances, and good trade pracces
3. Product connected to voltage other than indicated on nameplate or labels
DISCLAIMER:
Any oral statements about the product made by the seller, the Barracuda Pumps, the representaves, or any other pares do not constute warranes, shall not be relied upon by the
user, and are not part of the contract for sale. Seller’s and the Barracuda Pumpss only obligaon, and buyer’s only remedy, shall be the replacement and/or repair by the Barracuda Pumps
of the product as described above. NEITHER SELLER NOR THE BARRACUDA PUMPS SHALL BE LIABLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT, INCIDENTAL OR CONSEQUENTIAL
(INCLUDING, BUT NOT LIMITED TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR PROPERTY, OR ANY OTHER INCIDENTAL OR
CONSEQUENTIAL LOSS), ARISING OUT OF THE USE OR THE INABILITY TO USE THE PRODUCT, AND THE USER AGREES THAT NO OTHER REMEDY SHALL BE AVAILABLE TO IT. Before using, the
user shall determine the suitability of the product for his/her intended use, and user assumes all risk and liability whatsoever in connecon therewith.
THE WARRANTY AND REMEDY DESCRIBED IN THIS LIMITED WARRANTY IS AN EXCLUSIVE WARRANTY AND REMEDY AND IS IN LIEU OF ANY OTHER WARRANTY OR REMEDY,
EXPRESSED OR IMPLIED, WHICH OTHER WARRANTIES AND REMEDIES ARE HEREBY EXPRESSLY EXCLUDED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT EITHER APPLIES TO A PRODUCT SHALL BE LIMITED IN DURATION TO THE PERIODS OF THE EXPRESSED
WARRANTIES GIVEN ABOVE.
Some states and countries do not allow the exclusion or limitaons on how long an implied warranty lasts or the exclusion or limitaon of incidental or consequenal damages, so the
above exclusion or limitaons may not apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
Customer Support
800-495-9278
barracudapumps.com

SKU: 691-1615
UNIVERSAL TETHERED FLOAT SWITCH
Risk of electrical shock. Can burn or kill. To reduce risk of electrical shock, disconnect the power supply before replacing switch. Make
sure switch is connected only to a properly grounded grounding type receptacle.
Short circuit electrical hazard. An incorrect connection may cause electric shock, or burn out the pump motor, resulting in property
damage or personal injury. Make sure all connections are correct before plugging the switch into the outlet.
The outlet voltage and pump voltage must match. Ensure voltage is correct before installing switch. The electrical outlet must be
installed outside the pump basin.
Risk of flooding. It is recommended to operate the pump through two or three complete cycles to ensure proper liquid level control.
Installation and Operating Instructions
1. Determine the required tether length/pumping range for your
installaon using the dimensions in the Tether Length Chart.
Refer to Figure 2.
2. Aach the oat switch cable to the pump discharge pipe using
the plasc mounng clamp and stainless hose clamp (see
Figure 1). NOTE: Do not install the cord under the hose clamp.
3. Locate the clamp at the desired acvaon level and secure to
the discharge pipe.
4. Make sure the oat operates freely without contacng the
sides of the basin.
5. Secure remaining cord to the discharge pipe to avoid possible
obstrucon with the oat switch operaon.
6. Plug the piggyback plug of the oat switch into a grounded
outlet, then plug the pump into the piggyback plug. Refer to
Figure 3.
7. Check for proper operaon by lling the basin with water and
observing the oat switch through at least two complete
cycles. Make sure the pump operates at the desired levels.
Make any necessary adjustments at this me.
Installation & Operating Instructions For
Barracuda Brand Pumps
1. Remove the old oat switch from the pump by removing the screw and
cord clamp.
2. Determine the required tether length/pumping range for your installaon
following the dimensions in the Tether Length Chart or measure the tether
length from the old switch.
3. Aach the stainless steel cord clamp to the new oat switch cord at the
desired tether length.
4. Aach clamp to the pump using the appropriate screw & washer. Refer to
Figure 4.
5. Plug the piggyback plug of the oat switch into a grounded outlet, then
plug the pump into the piggyback plug. Refer to Figure 3.
6. Check for proper operaon by lling the basin with water and observing
the oat switch through at least two complete cycles. Make sure the pump
operates at the desired levels. Make any necessary adjustments at this
me.
* Pump Sold Separately
Aach the oat
switch to the top
of the pump .
Before ghtening
adjust tether
length. Pump
Sold
Separately
Switch
Tether Length Chart
Tether Length 3.5" 6" 9" 12" 15" 18" 22"
Pumping Range 8" 11" 15" 21" 28" 31" 36"
Figure 2
Figure 3
Plug Pump
in here
To Outlet
Figure 1
Figure 4
Safety Guidelines
Washer
Screw
Cord Clamp