Bartell BR68 User manual

Doc. # OI-B09014
Orig. Rel. 12/2008
Curr. Rev. - 03
Rev. Date - 05/2011
OWNER’S
MANUAL
Bartell Morrison Inc.
375 Annagem Blvd.,
Mississauga, ON, Canada
L5T 2A7
Toll Free (N.A.): 1 866 501 1683
Local: [phone]
Fax: [phone]
RAMMER
BR68
ORIGINAL
LANGUAGE
Doc. # OI-B09014
Orig. Rel. - 12/2008
Curr. Rev. - 08
Rev Date - 06/2014

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX [phone]
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX [phone]
CREATED: 07/04
REVISED: 06/14
RAMMER INSTRUCTION MANUAL
BARTELL MORRISON INC.
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO,
CANADA, L5T 3A7,
LOCAL 905-364-4200 FAX [phone]
Created: 12/08
Revised: 05/11
BARTELL MORRISON (USA) LLC
25 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY,
USA, 07735,
LOCAL 732-566-5400 FAX [phone]
SAFETY PRECAUTIONS
DANGER
EXPLOSION HAZARD
Never operate the machine in an
explosive atmosphe
re, near
combustible materials or where
ventilation does not clear exhaust
fumes.
WARNING
BURN HAZARD
Never come into contact with the
engine or muffler when engine is
operating or shortly after it is
turned off. Serious burns may
occur.
CAUTION
MOVING PARTS
Before starting the machine ensure
that all guards and safety devices
are in place and functioning
properly.
CAUTION
MACHINE DAMAGE
Advance cutter depth in small
increments to avoid premature
blade wear or damage.
ATTENTION
READ OWNERS MANUAL
Read and understand operator's
manual before using this machine.
Failure to follow operating
instructions could result in serious
injury or death.
!
!
!
!
!

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX [phone]
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX [phone]
CREATED: 07/04
REVISED: 06/14
RAMMER INSTRUCTION MANUAL
BARTELL MORRISON INC.
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO,
CANADA, L5T 3A7,
LOCAL 905-364-4200 FAX [phone]
Created: 12/08
Revised: 05/11
BARTELL MORRISON (USA) LLC
25 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY,
USA, 07735,
LOCAL 732-566-5400 FAX [phone]
UPRIGHT RAMMER
Read this material before using this product. Failure to do so can result in serious injury.
SAVE THIS MANUAL.
IMPORTANT!
YOUR WARRANTY IS VOIDED IF:
You do not put engine oil in the Engine’s crankcase prior to its rst use.
Never run the Engine with low or no engine oil
Running the Engine with low or no engine oil WILL permanently damage the Engine.
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating, inspection,
maintenance and cleaning procedures. Write the product’s serial number in the back of the
manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
IMPORTANT SAFETY INFORMATION
In this manual, on the labeling, and all other information provided with this product:
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
DANGER! DANGER indicated a hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING! WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION! CAUTION, used with the safety alert symbol, indicates a hazardous
situation which, if not avoided, could result in minor or moderate injury.
NOTICE! NOTICE is used to address practices not related to personal injury.
CAUTION CAUTION, without the safety alert symbol, is used to address practices
not related to personal injury.
GENERAL SAFETY RULES
WARNING! Read all instructions
Failure to follow all instruction listed below may result in serious injury.
SAVE THESE INSTRUCTIONS
Work area safety1.
Keep work area clean and well lit. Cluttered or dark areas invite accidents.a.
Do not operate power tools in explosive atmospheres, such as in the presence ofb.
ammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX [phone]
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX [phone]
CREATED: 07/04
REVISED: 06/14
RAMMER INSTRUCTION MANUAL
BARTELL MORRISON INC.
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO,
CANADA, L5T 3A7,
LOCAL 905-364-4200 FAX [phone]
Created: 12/08
Revised: 05/11
BARTELL MORRISON (USA) LLC
25 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY,
USA, 07735,
LOCAL 732-566-5400 FAX [phone]
Keep children and bystanders away while operating a power tool. Distractions canc.
cause you to lose control.
Personal safety2.
Stay alert, watch what you are doing and use common sense when operating aa.
power tool. Do not use a power tool while you are tired or under the inuence of
drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Use safety equipment. Always wear eye protection. Safety equipment such as dust b.
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
Avoid accidental starting. Ensure the switch is in the off-position when the unit is notc.
in use. Carrying power tools with your nger on the switch or plugging in power tools
that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench ord.
a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables bettere.
control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing andf.
gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in
moving parts.
Power tool use and care3.
Do not force the power tool. Use the correct power tool for your application. Thea.
correct power tool will do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn it on and off. Any power toolb.
that cannot be controlled with the switch is dangerous and must be repaired.
Store idle power tools out of the reach of children and do not allow personsc.
unfamiliar with the power tool or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or binding of moving parts, breakaged.
of parts and any other condition that may affect the power tools operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
Use the power tool in accordance with these instructions and in the manner intendede.
for the particular type of power tool, taking into account the working conditions and
the work to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
Service4.
Have your power tool services by a qualied repair person using only identical a.
replacement parts. This will ensure that the safety of the power too is maintained.
SPECIFIC SAFETY RULES
Using an engine indoors CAN KILL YOU IN MINUTES. Engine exhaust contains carbon1.
monoxide. This is a poison you cannot see or smell. NEVER use inside a home or
garage, EVEN IF doors and windows are open. Only use OUTSIDE and far away from
windows, doors, and vents.
Fire and explosion2. HAZARD! Do not ll while engine running or hot, while smoking, or if
damaged. Do not overll.
Hold securely with both hands on proper handle locations. Creates strong forces during3.

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX [phone]
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX [phone]
CREATED: 07/04
REVISED: 06/14
RAMMER INSTRUCTION MANUAL
BARTELL MORRISON INC.
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO,
CANADA, L5T 3A7,
LOCAL 905-364-4200 FAX [phone]
Created: 12/08
Revised: 05/11
BARTELL MORRISON (USA) LLC
25 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY,
USA, 07735,
LOCAL 732-566-5400 FAX [phone]
operation. Pregnant women or inrm persons should consult physician before use.
Keep children away during use. Store out of reach of children with engine switch and4.
fuel lever turned off.
Wear steel-toed work boots, ANSI-approved safety goggles, dust mask, ear protection,5.
and heavy-duty work gloves during use.
Keep out from under base.6.
Move carefully and securely in upright position. Refer to manual for details. Rammer7.
extremely top heavy.
Maintain labels and nameplates on the tool. These carry important safety information.8.
The Spring Retaining Base Plate retains heavy springs under compression. When9.
removing the Base Plate, follow the instructions in the “Maintenance” section of this
manual carefully to avoid serious personal injury.
Never perform service or repairs on the Rammer while it is running. Always stop the10.
engine and remove the spark plug to prevent accidental starting.
Make sure all safety guards are in place and in proper working condition.11.
People with pacemakers should consult their physician(s) before use. Electromagnetic12.
elds in close proximity to heart pacemaker could cause pacemaker interference or
pacemaker failure. In addition, people with pacemakers should adhere to the following:
Caution is necessary when near the magneto, spark plug, and park plug wire or a
running engine. The engine should always be off if adjustments are to be made.
The warnings, precautions, and instructions discussed in this instruction manual cannot13.
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
SPECIFICATIONS
IMPORTANT!
This product requires oil and fuel to be added before starting. Attempting to start the Engine
without oil WILL ruin the Engine and void the Warranty.
NOTE:
The Engine’s carburetor may need to be adjusted by a qualied mechanic for high-altitude use.
Model BR68
Motor Petrol, Honda GX100
Power kW (hp) 2.2 (3.0)
Operation Mass kg (lbs) 68 (149)
Percussion Rate per min. 640-695
Impact Force kg 1300
Jumping Stroke mm 40-85
Fuel Tank Capacity L 2.8
Shoe Size mm (in) 330x285 (13x11)
Dimension mm (in) 430x760x1020 (17x31x40)

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX [phone]
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX [phone]
CREATED: 07/04
REVISED: 06/14
RAMMER INSTRUCTION MANUAL
BARTELL MORRISON INC.
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO,
CANADA, L5T 3A7,
LOCAL 905-364-4200 FAX [phone]
Created: 12/08
Revised: 05/11
BARTELL MORRISON (USA) LLC
25 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY,
USA, 07735,
LOCAL 732-566-5400 FAX [phone]
WARNING! Risk of accidental starting; resulting in serious personal injury. Turn the
Power Switch of the tool to its “OFF” position and remove the spark plug
before making any adjustments to the tool.
NOTE: For additional information regarding the parts listed in the following pages, refer to the
Assembly Diagram near the end of this manual.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning
of this manual including all text subheadings therein before set-up or use of this
product.
To Transport the Upright Rammer
CAUTION!1. The Upright Rammer is extremely top heavy. Move carefully and securely
in an upright position. With additional assistance, strap the Rammer to a dolly capable
of supporting the weight of the Rammer. Then carefully move the Rammer to the work
location. (See Figure A).
Pre-start instructions
IMPORTANT!1. Your Warranty is voided if you do not put engine oil in the Engine’s
crankcase prior to its rst use. Before each use, check the oil level. Never run the
Engine with low or no engine oil. Running the Engine with low or no engine oil WILL
permanently damage the Engine and void the Warranty.
The Engine2. MUST be lled with a high quality, 10W/30 grade engine oil.
Dolly
Strap
Strap
Strap
Figure A
Note:
Straps and Dolly
not included with
Rammer.

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX [phone]
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX [phone]
CREATED: 07/04
REVISED: 06/14
RAMMER INSTRUCTION MANUAL
BARTELL MORRISON INC.
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO,
CANADA, L5T 3A7,
LOCAL 905-364-4200 FAX [phone]
Created: 12/08
Revised: 05/11
BARTELL MORRISON (USA) LLC
25 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY,
USA, 07735,
LOCAL 732-566-5400 FAX [phone]
To add engine oil, unscrew and remove the Oil Dipstick. Pour approximately3. 20 ounces
of engine oil into the Oil Receptacle. Do not overll. Then screw the Oil Dipstick back
into the Oil Receptacle. (See Figure B).
To ll the Fuel Tank, unscrew and remove the Fuel Tank Cap. Fill the Fuel Tank with 4.
approximately ¾ gallon of unleaded gasoline. Avoid fuel spills. Wipe off any spilled
fuel. Then replace the Fuel Tank Cap. WARNING! NEVER attempt to ll the Fuel Tank
when the Engine is running or hot. (See Figure C).
Fuel Cap Fuel Tank
Figure C
Oil Fill Port
Figure B

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX [phone]
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX [phone]
CREATED: 07/04
REVISED: 06/14
RAMMER INSTRUCTION MANUAL
BARTELL MORRISON INC.
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO,
CANADA, L5T 3A7,
LOCAL 905-364-4200 FAX [phone]
Created: 12/08
Revised: 05/11
BARTELL MORRISON (USA) LLC
25 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY,
USA, 07735,
LOCAL 732-566-5400 FAX [phone]
To start the Engine
Unscrew and remove the Hex Bolt (1A) located at the top of the Transmission Housing1.
(3A). Check to make sure the oil is level with the oil ll receptacle in the Housing. If
necessary, top off with S.A.E. 20W/50 oil. Then replace the Hex Bolt. (See Figure G).
Make sure to position the Upright Rammer on a at, level ground surface.2.
Check to make sure the Engine’s On-Off Switch (27) is in its “OFF” position.3. (See
Figure D).
Turn the Engine’s Fuel Valve to its “OPEN” position.4. (See Figure D).
Move the Engine’s Throttle Lever to the “COLD” position. Make sure to move the5.
Engine’s Throttle Lever to the “IDLE” position when starting a warm engine. (See Figure
E).
Turn the Engine’s On-Off Switch to its “ON” position.6. (See Figure D).
Grasp the Starter Handle, and pull slowly until resistance is felt. Allow the Starter Rope7.
to rewind slowly. Then pull the Starter Handle with a rapid, full arm stroke. Allow the
Starter Rope to rewind slowly. If necessary, repeat this procedure until the Engine starts.
(See Figure F).
Allow the engine to warm up. Grasp the Rail rmly and slowly pull the Throttle Lever8.
Indicator towards the RUN position. The Rammer will commence the pounding action.
Never accelerate to wide open throttle position from the resting position. Allow yourself
time to get the feel and required control over guiding the Upright Rammer.
To turn off the Engine, turn the Engine’s On-Off Switch to its “OFF” position. Then turn9.
the Fuel Shut-off Valve to its “CLOSED” position. (See Figures D and E).
Fuel
Shut-off
Valve
On-Off
Switch
Figure D

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX [phone]
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX [phone]
CREATED: 07/04
REVISED: 06/14
RAMMER INSTRUCTION MANUAL
BARTELL MORRISON INC.
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO,
CANADA, L5T 3A7,
LOCAL 905-364-4200 FAX [phone]
Created: 12/08
Revised: 05/11
BARTELL MORRISON (USA) LLC
25 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY,
USA, 07735,
LOCAL 732-566-5400 FAX [phone]
Machine Operation
WARNING!1. When operating the Upright Rammer, make sure to keep your feet clear
from the Bottom Plate to avoid personal injury.
CAUTION!2. Never operate the Upright Rammer on hard, unyielding surfaces to avoid
damage to the machine.
CAUTION!3. Always use both hands when operating the Upright Rammer.
When operating, guide the Rammer with both hands, but allow the machine to do the4.
work. Bearing down on the handle is unnecessary and limits the Bottom Plate ramming
action.
On nearly level surfaces, the Upright Rammer moves forward in rapid jumps. On5.
uneven surfaces or inclines, rocking the handle slightly may assist the Rammer in
moving forward.
Always guide the Rammer so that the entire Bottom Plate, and not just the front or back6.
edge, does the impacting.
To start the machine operation, move the Throttle Lever to the “RUN” position.7. (See
Figure E).
As the soil becomes compacted, the jump height of the Rammer will increase.8.
With practice, you will learn how to adjust the technique to the specic work conditions.9.
MAINTENANCE AND SERVICING
WARNING! Risk of serious personal injury from accidental starting. Turn the Power
Switch of the tool to its “OFF” position and remove the spark plug before
performing any inspection, maintenance, or cleaning procedures.
Damaged equipment can fail, causing serious personal injury. Do not
use damaged equipment. If abnormal noise or vibration occurs, have the
problem corrected before further use.
Cleaning, maintenance, and lubrication
BEFORE EACH USE1. , inspect the general condition of the tool. Check for loose screws,
misalignment or binding of moving parts, cracked or broken parts, damaged or worn
Shoe (3C), and any other condition that may affect its safe operation.
BEFORE EACH USE2. , unscrew and remove the Fill Plug located at the top of the
Transmission Housing. Check to make sure the oil is level with the oil ll receptacle in
the Housing. If necessary, top off with S.A.E. 20W/50 oil. Then, replace the Hex Bolt.
(See Figure G).
Fill Plug
Sight Gauge
Drain Plug
Figure G

375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-364-4200 FAX [phone]
200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-6400 FAX [phone]
CREATED: 07/04
REVISED: 06/14
RAMMER INSTRUCTION MANUAL
BARTELL MORRISON INC.
375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO,
CANADA, L5T 3A7,
LOCAL 905-364-4200 FAX [phone]
Created: 12/08
Revised: 05/11
BARTELL MORRISON (USA) LLC
25 INDUSTRIAL DRIVE, KEYPORT, NEW JERSEY,
USA, 07735,
LOCAL 732-566-5400 FAX [phone]
EVERY 300 OPERATING HOURS OR 6 MONTHS,3. drain the old oil from the
Transmission Housing and rell with approximately 27 ounces of clean, new S.A.E.
20W/50 oil. To do so, unscrew and remove the Fill Plug located at the top of the
Transmission Housing. Unscrew and remove the Drain Plug located at the bottom of
the Cylinder Cover Body and allow the old oil to drain into a proper container. Allow the
old oil to completely drain. Replace the Drain Plug at the bottom of the Cylinder Cover
Body. Rell the Transmission Housing with new oil. Then replace the Fill Plug at the top
of the Transmission Housing. (See Figure G).
AFTER USE,4. clean external surfaces of the tool with a garden hose. Do not spray the
Engine with water or other liquids.
WHEN STORING,5. drain all fuel out of the Engine’s Fuel Tank (See Engine
manufacturer’s manual). If this is not done, old fuel in the Engine’s Fuel Tank and
Carburetor may become contaminated (average “fuel life” is approximately 90 days)
and prevent the Engine from starting until cleaned out. Do not drain the oil. Always
store the Upright Rammer in a clean, dry, safe location out of reach of children and other
unauthorized people.
ENGINE MAINTENANCE6. : Refer to the Engine manufacturer’s manual (included) for
complete Engine maintenance instructions.
CAUTION7. !All maintenance, service, and repairs not mentioned in this manual must
only be performed by a qualied service technician.
PROBLEM POSSIBLE CAUSES PROBABLE SOLUTIONS
Engine will 1. Power Switch is in “OFF” position. 1. Turn Power Switch to “ON” position.
not start
2. Low on fuel or oil. 2. Add fuel or oil.
3. Faulty Spark Plug. 3. Clean or replace Spark Plug.
4. Throttle Lever in wrong position. 4. Properly adjust Throttle Lever.
5. Fuel Valve in “CLOSED” position. 5. Open Fuel Valve.
6. Spark Plug Wire loose. 6. Attach Wire to Spark Plug.
7. Fuel Line clogged. 7. Clean Fuel Line.
8. Air Filter clogged. 8. Clean Air Filter.
9. Fuel contaminated. 9. Drain fuel and replace with new fuel.
10. Faulty ignition system. 10. Have a qualied technician check
ignition system.
Rammer not 1. Improper use of machine. 1. Refer to “Machine Operation” section.
compacting
properly.