Baumatic BR508 User manual

He
BR508 Built under
freezer

2
USER MANUAL FOR YOUR BAUMATIC
BR508 Built under
freezer
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference. for
you or any person not familiar with the operation of the appliance.
DD 08/12/11

3
Contents
Environmentalnote 4
Important safety information 5 – 6
Specifications of your freezer 7 – 8
Dimensions 7
Descriptionoftheappliance 8
Using your Baumatic freezer 9 -11
Beforeswitchingon 9
Duringfirstuse 9
Switching on the appliance and setting the thermostat 10
ControlPanel 11
The freezer compartment 11-14
Freezing fresh food 12
Tips on freezing 12-13
Makingicecubes 13
Freezing with fast freeze 13-14
Saving energy when using your freezer 14-15
Cleaning and maintenance 15-17
Defrosting the freezer compartment 16-17
Installation 17-25
Electrical connection 17-18
Positioning 18
Reversing the door of your appliance 18-20
Aperturedimensions 21
Adjusting the plinth/kickboard 21-22
Fitting the furniture door to the appliance 22-26
Troubleshooting 26-27
Baumatic consumables 28
Technicaldata 29
Contactdetails 30

4
Environmental note
Note : Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.

5
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Advice Line.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
Use of the appliance
oYour appliance is only designed to be used in the
home. It is suitable for freezing and storing frozen
food. If it is used for any other purpose or it is not
used correctly, then Baumatic Ltd. will accept no
liability for any damage that might be caused.
oAltering the specification of the appliance must not be attempted
for reasons of safety.
Before using your appliance
oCheck the appliance for any signs of transport damage. If you
notice any damage, then you should not connect your appliance
to your mains supply and should contact your supplier.
Refrigerant
oYour appliance contains R600a refrigerant, which is a natural gas
that does not contain CFCs that can damage the environment.
However it is a flammable substance, therefore care should be
taken:
During the transportation and installation of the
appliance, make sure that the refrigeration pipework
does not get damaged.
If it does become damaged then sources of ignition
and open flames should be avoided. Also the room
that the appliance is situated in should be thoroughly
ventilated.
oDo not place any objects on top of the appliance,
as this may damage the table top.

6
Child safety
oPackaging material should be kept away from
children.
oChildren should not be allowed to touch the
controls or play with the appliance.
General safety
oDo not pull on the power supply cable to remove the plug from
your mains supply socket.
oDo not pull out or insert the plug with wet hands.
oDo not attempt to use your appliance outdoors or
any place where it is likely to come into contact
with the elements.
oBefore cleaning the appliance or performing
maintenance work, ensure that the appliance has been
disconnected from your mains supply.
oNever allow the back coils of the appliance to come into contact
with the wall surface.
oAlways ensure that the location where you are installing your
appliance is free of stored items such as papers and other
flammable materials.
oNever block the ventilation openings of the appliance, either on
the inside or its exterior.
oIt is vital to keep your appliance well ventilated,
so that there is proper air flow between the
bottom of the unit and the plinth/kick plate
which it is sitting on.
oDo not place electrical devices inside of the appliance, such as
mixers and electric ice cream makers.
Service
You should not attempt to repair the appliance
yourself, as this could cause injury or a more serious
malfunction. If you require a service call then please
contact the Customer Care Department.

7
Specifications of your freezer
Dimensions of appliance
Height: 818 - 868 mm
Width: 596 mm
Depth: 550 mm
Dimensions of aperture*
Height: 820 – 870 mm
Width: 600 mm
Depth: 560 mm (min)
oFreezer star rating ****
oManual defrost
oAdjustable thermostat
oLED controls
oTemperature rise warning indicator
oFast freeze switch
oFast freeze indicator light
o3 wire baskets
oReversible door
oDoor on door fittings
oAdjustable feet
Cubic capacities
oGross capacity: 108 litres
oNet capacity: 91 litres

8
Energy efficiency class
Energy class: A
* Please refer to the installation instructions for more specific
information on the size of aperture that you will require.
IMPORTANT: When you install your appliance it is important to bear
in mind its climatic rating.
In order to find out the climatic rating of your appliance, you should
check the rating plate. The rating plate is located on the front left edge
of the inside of the fridge. You will need to open the door of your
appliance to be able to find it.
The rating plate will indicate the ambient temperature range that your
appliance will function correctly within.
Description of the appliance

9
Using your Baumatic freezer
Before switching on
oMake sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
oAfter delivery, wait for eight hours before connecting the
appliance to your mains supply. This will allow any refrigerant
gasses that may have been disturbed during the transportation
process to settle.
oThe outside of the appliance and the removable accessories
contained within it, should be cleaned with a solution of liquid
detergent and water.
oThe interior of the appliance should be cleaned
with a solution of sodium bicarbonate dissolved in
lukewarm water. The interior and accessories
should be thoroughly dried, after the cleaning
process has been completed.
oThere can be an odour when you first switch on the appliance. It
will lessen as the appliance starts to cool.
During first use
oYou should set the thermostat dial to its maximum setting for 24
hours after switching on the appliance for the first time.
oWhen you first switch on the appliance, the compressor will run
continuously for approximately 24 hours or until the freezer
reaches a cool enough temperature.
oDuring this period of time, you should try not to open the door
frequently or place a large amount of food within the appliance.
oYou should then adjust the thermostat dial down to its normal
operating position.
oIf the unit is switched off or unplugged, you must allow at least 5
minutes before restarting the appliance on the thermostat or
connecting it to your mains supply.

10
Switching on the appliance and setting the thermostat
You switch on your appliance by connecting it to your mains supply
and setting the thermostat. The thermostat control knob is located at
the top of the appliance.
oThe thermostat automatically regulates the temperature inside
the freezer, depending on what number you have turned the
thermostat control knob to:-
oPosition <0> means that the appliance will not cool. However
the light will still function.
oPosition <1> will give you a higher temperature inside the
freezer.
oPosition <4> will give you a lower temperature inside the
freezer.
oIdeally the thermostat should be set to a position between <2>
to <3>.
oThe freezer can cool down to -18 degrees centigrade and lower.
oIMPORTANT: The ambient temperature of the room,
the temperature of food and the amount of food that
has been placed in the appliance and how often the door
is opened, will all affect the temperature being
maintained by the appliance.
oOn the maximum setting (position <4>), your freezer will work
harder to maintain a lower temperature and will increase the
energy usage. There is no need to run your appliance on this
setting for prolonged periods. Unless you are freezing fresh food,
you should have the thermostat set to position <2> or <3>.

11
Control panel
oFast freeze light (Orange) - will light up when the fast freeze
switch has been activated.
oTemperature rise warning light (Red) - will light up when
the appliance detects a rise in temperature that could affect the
contents of your freezer.
oPower light (Green) - will light up as soon as the appliance is
connected to your mains supply.
The freezer compartment
The freezer compartment is suitable for storing and freezing food.
oThe freezer compartment temperature must have already
reached -18 degrees centigrade (or lower) before you attempt to
store food that is already frozen or freezing fresh food.
oThe freezer compartment is only able to freeze a certain quantity
of food at one time. You should not attempt to freeze more than
9 kilograms of fresh food within a 24 hour period.
oWarm food should be allowed to cool down before you attempt
to freeze it. If you place warm food in the freezer, then the
increased humidity will cause quicker ice formation and increase
the amount of power that the appliance uses.
oThe guidance of the food manufacturer should be followed, in
regard to the maximum storage time.
oThawed foods must not be frozen for a second time.

12
oDo not open the freezer door too often or leave the door open
for long periods of time, as this will increase the temperature
inside of the appliance and will increase the energy usage.
Freezing fresh food
oTo freeze the maximum quantity of fresh food
specified above, you should turn the
thermostat knob to position <4>, 24 hours
prior to attempting freezing.
oFor smaller quantities of fresh food, you
should turn the thermostat knob to position
<4>, approximately 6 hours prior to
attempting freezing.
oAlternatively you can use the fast freeze option (see the
“Freezing with fast freeze” section of this booklet).
oFresh food should be packed into airtight containers
or packaging. This will help to make sure that the
food doesn’t dry out or lose its flavour. It will also
ensure that flavour does not transfer from other
foods.
oDo not allow fresh food to touch items
that are already frozen.
oAfter 24 hours you should check that
the fresh food is satisfactorily frozen.
If it is then the thermostat should be
turned down to its normal setting
(between <3> and <4>).
Tips on freezing
oFreezer bags, polythene wraps, aluminium foil (extra thick) and
special cans for frozen foods are suitable packaging for storing
frozen goods in.
oTape, rubber bands or plastic clips are
suitable for sealing bags and wrappings.
oBefore sealing a suitable bag, you should
compress the air out of it, as this will help
the food to freeze more easily.

13
oFlat packages freeze more easily.
oIf you are freezing liquid, then do not fill the container to the
brim. Liquids will expand when being frozen.
oDo not place bottles (glass or tin)
containing liquids (especially sparkling
liquids) into the freezer as they could
cause the bottle to burst during freezing.
Making ice cubes
oFill an ice cube tray with water and place it in the freezer
compartment.
oAfter the water is completely frozen and turned to ice, you can
twist the ice cube tray (as shown in the drawing below) to
dispense the ice.
Freezing with fast freeze
oPress the fast freeze switch and the freezer will start to run
continuously at its maximum setting.

14
oThe orange fast freeze light will come on when the fast freeze
setting has been switched on.
oThere is no need to adjust the thermostat knob.
oThe freezer temperature will decrease and the appliance will get
to its lowest temperature.
oPlace the food that is to be frozen inside the freezer.
oOnce the food is frozen, you should switch off the fast freeze
setting. DO NOT SWITCH OFF THE FAST FREEZE SETTING
UNTIL THE FOOD IS FULLY FROZEN.
oThe orange fast freeze light will go out and your appliance will
return to normal operation.
oIMPORTANT: DO NOT LEAVE THE APPLIANCE RUNNING IN
FAST FREEZE MODE FOR LONGER THAN 24 HOURS AT A
TIME.
Saving energy when using your freezer
Installing:
oInstall the appliance in a cool position. If it is placed in direct
sunlight or next to an oven or other heat source, the energy
consumption can increase substantially.
oEnsure the appliance is installed with the correct ventilation
requirements. Restricting ventilation can increase the energy
consumption by 15%.
Cleaning and Maintenance:
oOccasionally clean the condenser coils (if present) at the back of
the appliance to maintain a high performance level.
oDefrost the appliance regularly. A build up of thick ice decreases
the efficiency of the appliance. You should defrost whenever the
frost reaches 5 mm thickness.
oClean the door gasket with warm water or a neutral detergent
that leaves no residue. A tight-sealing door gasket is critical to
the efficiency of your appliance.

15
Usage:
oDo not open the door repeatedly or more frequently than you
have to.
oDo not set the thermostat too low. A change of just one degree
can effect the energy consumption by 5%. Use a thermometer to
check the temperature.
oThe freezer should operate at -15 to -18 degrees Celsius.
oAllow food to sufficiently cool before putting it in the appliance
(but don’t let it sit at room temperature for too long).
oIn the freezer, food packages should be scattered and never
grouped or stacked together until they are completely frozen.
oIf you are going away for a long period of time, turn off the
appliance, empty and clean it and leave the door ajar.
oIf you have a second appliance that is not used, make sure that
it is stored with the power off and the door left ajar until it is
actually required.
Disposing:
oIf you're going to throw out your old freezer, see if there's a
chlorofluorocarbons (CFCs) recycler in your area. The
government department which looks after the environment in
your area may be able to help you.
Cleaning and maintenance
WARNING: PLEASE ENSURE THAT YOUR
APPLIANCE IS DISCONNECTED FROM
YOUR MAINS SUPPLY BEFORE
ATTEMPTING TO CLEAN IT.
oDo not clean the appliance by pouring water onto
it or spraying water over it.
oThe freezer should be cleaned periodically, using a
solution of bicarbonate of soda and lukewarm water.

16
oClean the accessories separately with soap and water. Do not
clean them in a dishwasher.
oDo not use abrasive products, detergents or soaps.
oAfter washing the appliance, wipe over the area
that you have cleaned with a damp cloth and then dry it
thoroughly.
oWhen cleaning is complete, dry your hands and then reconnect
the plug to your mains supply.
Defrosting the freezer compartment
The frost in the freezer compartment should be removed periodically.
You can use a plastic scraper to keep down the amount of frost that
builds.
oIMPORTANT: The freezer should be defrosted at least
twice a year. The number of times that you need to
defrost it, will depend on the setting of your thermostat
and how much food you freeze and store in the freezer.
oThe day before you defrost, turn the thermostat dial to position
<4>, this will make sure that the food contained in the freezer is
frozen properly.
oWhilst defrosting the appliance, the food should be removed
from the freezer and wrapped in several layers of paper and
stored in a cool place. The foods rise in temperature will shorten
its storage life and therefore the food should be used within a
relatively short period of time.
oDO NOT PLACE FOOD BACK IN THE FREEZER ONCE IT HAS
STARTED TO THAW.
oSet the thermostat knob to position <0> and disconnect the
appliance from your mains supply.
oLeave the door to the freezer open. You can place a bowl of
warm water inside the freezer to speed up the defrost process.
oYou can use a sponge to mop up the defrost water that will run
into the bottom of the freezer.

17
oIMPORTANT: You should place some old towels on the flooring
that is immediately in front of the appliance. In case any defrost
water comes out of the freezer and onto the floor.
oOnce all the ice that has built up has melted, then the inside of
the freezer should be dried thoroughly. Failure to do this will
result in immediate ice build when the appliance is switched back
on.
oWith dry hands, reconnect your appliance to your mains supply.
Set the thermostat knob to position <4> for a 24 hour period,
before returning it to the normal setting of between <2> and
<3>.
oYou should not attempt to freeze fresh food inside the freezer
until this 24 hour time period has elapsed.
oDo not defrost the appliance with other electrical devices
(e.g. hair dryer). Do not use sharp metal objects to
remove the ice on the freezer, as this could cause damage
to the refrigerant system.
Installation
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found on the front left edge of the
inside of the freezer.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.
Electrical connection
YOUR FREEZER IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
We recommend that the appliance is connected by a
qualified electrician, who is a member of the N.I.C.E.I.C.
and who will comply with the I.E.E. and local regulations.
oYour freezer comes supplied with a 13 amp plug fitted. If in
future you need to change the fuse in this plug, then a 13 amp
ASTA approved (BS 1362) fuse must be used.

18
oThe wiring in the mains lead is coloured as follows:
Brown Live
Blue Neutral
Green and yellow Earth
oAs the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals
in your spur box, please proceed as follows:
The brown wire must be connected to the terminal marked “L”
(live), or coloured red.
The blue wire must be connected to the terminal marked “N”
(neutral), or coloured black.
The green and yellow wire must be connected to the terminal
marked “E” (earth), or by the earth symbol, or coloured green
and yellow.
oWhen the connection is completed, no stray strands or cut wire
should be present. The cord clamp must be secured over the
outer sheath.
Positioning
oIt is advisable that your appliance is only installed in a location
where the ambient temperature of the room, corresponds with
the climate classification that is stated on the rating plate of your
appliance. Your appliance may not function correctly if the
ambient temperature falls outside of the following ranges.
oYour appliance should not be located in direct sunlight or
exposed to continuous heat or extremes of temperature (e.g.
next to a radiator or boiler).
oThe door should be able to open completely and freely.
oThe appliance should be situated so you can easily access the
food that is stored in it.
oYou should check whether there is an electrical socket available,
which will be accessible after your appliance is installed.
Climate classification Appropriate ambient temperature
SN +10 to +32 degrees centigrade
N +16 to +32 degrees centigrade

19
Reversing the door of your appliance
This procedure MUST be completed before the furniture
door is attached.
Any parts that you remove from the appliance whilst
reversing the door, should be retained for later use.
WARNING- Take care when opening the hinges, they
are sprung loaded and there is the risk of injury if
they close on your hand.
Tools required:-
oPhillips screwdriver
oFlat bladed screwdriver

20
oSlacken the retaining screws (1) on the appliance and then
carefully remove the appliance door.
oPlace the appliance door on a cushioned surface, so that damage
does not occur to it.
oLever off the cover caps (3).
oInsert the retaining screws (1) into the opposite side of the
appliance from their original position. These screws should be
partially tightened but not fully tightened.
oRemove the door retaining screws (2) and then reverse the
position of the top and bottom hinge (as shown in the diagram
on page 18).
oReattach the appliance door and then fully re-tighten the
retaining screws (1) and the door retaining screws (2).
oInsert the cover caps (3) into the holes that are now exposed on
the right hand side of the cabinet.
IMPORTANT: Check that the door opens and shuts correctly,
without fouling, after you have completed the door reversal
process.
After the door has been reversed, you should check
the door seal of the appliance. The seal should not
be creased or crushed; otherwise there will be a gap
between it and the inside of the door.
oThe seal must adhere properly all the way around the door.
oIf the seal is not adhering to the cabinet properly, then you
should either:-
1. Use a warm damp cloth and manipulate the seal until it does
adhere to the cabinet properly, all the way around the door.
or
2. Use a hair dryer on its lowest heat setting and lightly heat the
areas of the door seal that are not adhering correctly. The
heat will make the seal more pliable and this will allow you to
manipulate the seal into the correct position.
IMPORTANT: DO NOT HEAT THE DOOR SEAL ON ANYTHING BUT
THE LOWEST HEAT SETTING, OR HEAT THE SEAL FOR A LONG
PERIOD OF TIME. OTHERWISE DAMAGE MAY BE CAUSED TO