Baumatic BHI909TS. GWK User manual

1
BHI909TS.GWK
90cm Induction & Gas
Hob

User Manual for your Baumatic
BHI909TS.GWK
90 cm
Induction & Gas Hob
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
JW 17/05/13
2

3
Contents
Environmental note 4
Important safety information 5 – 8
Specifications 9–11
Productspecifications 9
Standardaccessories 10
Gas&Electricaldetails 10
Hobsurfacelayout 11
Controlpanellayout 12
Using the induction hob 12 - 22
Beforefirstuse 12
Touchcontrols 13
Switchingthehobon 13
Switching on a zone and setting a power level 14
Powerlevels 15
Theboostfunction 15
Switchingoffazone 16
Switchingthehoboff 16
Residualheatindicator 16
Pansensor 17
Cookware that is suitable for an induction hob 17
The hob timer (minute minder) 18
The hob timer (linked to a cooking zone) 19-20
Lockingthehobtop 20
Safetycut-off 21
High temperature protection 21
Hob guidelines 21 - 22
Usingthegashob 23-25
Switchingthehobon 23
Automatic ignition with flame failure device 24
Energysavingtips 25
Cleaning and maintenance 26 - 28
Cleaning the induction hob top 26
Aftereachuse 26
Cleaningtable 26
Using a induction hob scraper 27
Using a specialist induction hob cleaner 27
Cleaning the gas hob burner 27
Maintaining the cast iron pan stand 28
Installation 29-40
Positioning 29-31
Unpacking the appliance 31
Installingtheappliance 31-32
Electricalconnection 33-34
Connecting the mains supply cable 34
Replacing the mains supply cable 34
Gasconnection 35
Ventilation requirements 35-36
Gas Safety (Installation and Use) Regulations 37
GasAdjustment(ConversiontoLPG) 38
Minimum flow adjustment for hob gas taps 39
Gastapmaintenance 40
My appliance isn’t working correctly 41 - 43
Errorcodes 42
Baumatic consumables 44
Contactdetails 47

Environmental note
oThe packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
all packaging material with due regard for the
environment.
oPlease discard
4

5 5
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
ase contact Baumatic Customer Care.
usehold use and for the
e ambient temperature of the room it is located in,
r discolouration at temperatures below the
ntion of this temperature limit, will be the liability of the
uarantee. The foregoing does not affect your
ent of Baumatic Ltd. will
ld not use this appliance to store items on or as a work
be kept away from the
umatic service
engineers or their authorised service agent.
booklet, ple
General Information
This appliance is designed for domestic hoocooking and frying of domestic foodstuffs.
oIMPORTANT: The adjacent furniture and all materials used in the
installation must be able to withstand a minimum temperature of
85°C above th
whilst in use.
oCertain types of vinyl or laminate kitchen furniture are particularly
prone to heat damage o
guidelines given above.
oAny damage caused by the appliance being installed in
contrave
owner.
oYour new appliance is guaranteed against electrical or mechanical
defects, subject to certain exclusions that are noted in Baumatic’s
Conditions Of G
statutory rights.
oThe use of this appliance for any other purpose or in any other
environment without the express agreem
invalidate any warranty or liability claim.
You shouosurface.
oNo modifications to the appliance are permitted by Baumatic Ltd.
oYou should not store or place flammable or highly flammable
liquids/materials on top of or near the appliance. Items made from
aluminium, plastic or plastic film should also
appliance, as they may fuse to the surface.
Repairs may only be carried out by Bao

6
hild Safety
pliance at any time. During and after use, all surfaces
will be hot.
ensure that they are kept under close supervision at all
times.
n should only be allowed to utilise the appliance when
supervised.
eneral Safety
uld only be installed and connected by a suitably
qualified person.
that you build the appliance into, meet with the relevant standards.
only be installed and connected by a GASSAFE
registered installer.
ains supply. Otherwise there is the risk of electric shock
occurring.
appliance will become hot during use and retain
heat after use.
uring use
he hob surface when it is
delivered should be removed before use.
sing the appliance, otherwise there
is a risk of burns being caused.
to
contact with the hob surface when it is hot or any hot cookware.
oking with fat and oil the appliance should not be
left unattended.
re that all of the cooking zones are switched off after use.
C
oBaumatic strongly recommend that babies and young children are
prevented from being near to the appliance and not allowed to
touch the ap
oIf it is necessary for younger family members to be in the kitchen,
please
oOlder childre
G
oThe appliance sho
oCare should be taken to ensure that the units and work surfaces
oThe appliance should
oIf you notice any scratches, splits or cracks in the induction glass,
you should immediately switch off the appliance and disconnect it
from your m
oCAUTION: This
D
oAny film or stickers that are present on t
oCare should be taken when utili
oYou should not allow the electrical connection cables to come in
oIf fat and oil overheats, then it can ignite extremely quickly. For this
reason, when co
oMake su

7
leaning
Cleaning of the hob should be carried out on a regular basis.
nce, it should
be disconnected from the mains and allowed to cool.
t using this appliance and when
following the cleaning procedure.
any other high pressure cleaning
equipment to clean the appliance.
n
section of this booklet that refers to
installation.
lt of improper use
or incorrect installation of this appliance.
dation
Vehicle, the requirements of N 721 MUST be followed.
hat this appliance is
installed on any type of marine vessel.
eclaration of conformity
This appliance complies with the following European Directives:
/128/EEC This appliance is suitable to come in
004/108/CE Electromagnetic compatibility
ance must be used
by a trained person for domestic purposes only.
C
o
oIMPORTANT: Before attempting to clean the applia
oGreat care should be taken whils
oYou should not use a steam jet or
Installatio
This appliance must be correctly installed by a
GASSAFE registered installer, strictly in accordance
with the manufacturer’s instructions. Please see
the specific
oBaumatic Ltd. declines any responsibility for injury or
damage, to person or property, as a resu
oIf the appliance is being used in a Leisure Accommo
oBaumatic Ltd DOES NOT recommend t
D
-2006/95/CE General regulations / Low tension
-1935/2004/CE 90
contact with food
-2
oThe manufacturer declares that the hob is built using certified
materials and requires the appliance to be installed in accordance
with the standards currently in force. This appli

8
oIMPORTANT: The induction hob fully complies with current
legislation regarding electro-magnetic interference and is
designed not to interfere with other electronic appliances
providing these comply with the same legislation.
oAs the induction hob generates magnetic fields in its
immediate vicinity, pacemakers and active heart implants
must be designed to comply with relevant regulations. If in
doubt, you should consult the manufacturer of your device or
your doctor. In this respect, Baumatic can only guarantee
the conformity of our own product.
oIf an object made of metal, (e.g. saucepan lid, knife, fork or
spoon) is placed on a cooking zone that is switched on, it can
get hot.
To avoid damaging your appliance
oThe induction glass can be damaged by objects falling onto it.
oThe induction glass edge can be damaged by knocks from
cookware.
oCast iron and cast aluminium cookware with damaged bases may
scratch the induction surface if they are dragged across it.
oPans should be lifted on and off the hob surface and not dragged.
oCooking zones should not be switched on without cookware placed
on it. Also the cookware should not be empty.
oFood or liquid that has high sugar content may damage the hob
top, if it comes into contact with the induction hob surface. Any
spillages should be wiped up immediately, however this may not
prevent the hob surface from becoming damaged.

Specifications
Product dimensions: Aperture dimensions:
Depth: 510 mm Depth: 490 mm
Width: 900 mm Width: 880 mm
Height: 55 mm Height: 20 mm (min)
Product specifications:
1 x 3.00 kW induction zone (Ø 210 mm)
1 x 2.30 kW induction zone with booster (3.00 kW) (Ø 210 mm)
1 x 1.40 kW induction zone with booster (1.85 kW) (Ø 160 mm)
1 x 1.40 kW induction zone (Ø 160 mm)
oFront touch control operation
oSafety lock
o4 individual residual heat indicators
o4 independent induction generators
oElectronic timer
oPan compatibility detection
oBevelled edges
1 x 4.00 kW triple crown (wok) burner
oFront control operation
oHeavy duty cast iron pan stand
oAutomatic ignition
oFlame failure safety device on wok burner
9

10
Standard accessories
oInduction hob scraper
oLPG conversion jets
Electrical details
Rated Voltage: 220 - 240 Vac 50 / 60 Hz
Supply Connection: 40A (double pole switched fused
outlet with 3mm contact gap)
Max Rated Inputs: 7.40 kW
Mains Supply Lead: 3 core x 6 mm² (not supplied)
Gas details
Connection: Rp ½ (ISO R7)
Type: Natural Gas (20 mbar)
Alternative LPG G30 (28-30/37 mbar)
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of your hob is located on
the underneath of the appliance. Therefore it is a good idea to record
this information before you install your appliance.
Model Number ……………………………….
Serial Number ……………………………….
Date of Purchase ……………………………….

Hob surface layout
A) 3.00 kW induction zone (Ø 210 mm)
B) 1.40 kW induction zone (Ø 160 mm) (booster = 1.85 kW)
C) 2.30 kW induction zone (Ø 210 mm) (booster = 3.00kW)
D) 1.40 kW induction zone (Ø 160 mm)
E) Induction zone control panel
F) 4.00 kW triple crown gas burner
G) Gas wok zone control knob
11

Control panel layout
Induction hob
1) ON / OFF button
2) Plus button(s) / cooking zone
selection button(s)
3) Minus button
4) –
5) Timer button
6) Zone temperature / status
display(s)
7) Timer display
8) –
9) Timer indicator LED
10) –
11) Booster button
Gas Hob
F1) Single (inner) flame
F2) Duel flame
Using the induction hob
Before first use
IMPORTANT: You should clean the induction hob surface
(see “Cleaning and maintenance” section).
oYou should switch on one induction cooking zone at a time for 5
minutes at the maximum setting. This will help to eliminate any
new smell that exists and evaporate any humidity that has
formed on the heating elements during transit.
oDo not burn off more than one zone at once.
oYou must place a saucepan filled half full with cold water on
each zone as you burn it off. Otherwise the induction zone will
not operate.
12

Touch controls
oAll operations are performed by means of the touch controls that
can be found on the control panel.
oThe controls respond to touch so you do not need to add any
pressure.
oYou should use the ball of your finger not the tip when using the
controls.
oA beep will sound each time a touch is registered.
oYou should ensure that the controls are kept clean, dry and that
no objects such as utensils or cloths cover them. Even a thin film
of water may make the controls difficult to operate.
Switching the hob on
oWhen the hob is connected to a power supply the control panel
will initialise for about 3 seconds. The LED lights will illuminate
and the controls will not be operational during this time. Once
the initialisation has completed the hob will go into stand-by
mode. oTo turn the hob on you should press the ON/OFF
button.
oNOTE: Only the ON/OFF button can be pressed
when turning the hob on. If the hob detects
any other key activation it will remain in
stand-by mode.
oAll of the cooking zone indicators will show “0” and the
dot in the bottom corner of each cooking zone selector
(2) will flash to indicate that no zone has been selected.
13

Switching on a zone and setting a power level
IMPORTANT: A zone must be selected within 20 seconds of turning
the hob on. After this time the hob will return to stand-by mode.
oMake sure that the bottom of the pan and the
surface of the hob are clean and dry before
placing a suitable pan on the cooking zone that
you wish to use.
oPress the cooking zone selection button (2) of the
cooking zone that you want to use.
oSelect the power level for the cooking zone that you have
selected using the plus button of the zone you are using
and the minus button. If you do not choose a heat setting
within 20 seconds of turning the hob on, the hob will
switch off automatically.
oYou can alter the power level at any time during cooking using
the plus and minus buttons.
oIf the display flashes with the symbol shown
opposite, alternatively with the heat setting, this
means that:
You have not placed a pan on the correct cooking zone or,
The pan you are using is not suitable for induction cooking or,
The pan is too small or not properly centred on the cooking
zone.
oNo heating will take place unless there is a suitable pan on the
cooking zone. The display will automatically turn off after 20
seconds if no suitable pan is placed on it.
14

Power levels
oFor a general guide to cooking various foods at the different power
levels please refer to the table below.
oPlease note that this table should be viewed as a guide only and
that other factors such as cookware, weight and amount of food
and personal preference will all influence the power level required.
Power
Level Recommended Use
1 - 2 oDelicate warming of small amounts of food.
oMelting chocolate, butter and foods that burn
quickly.
oGentle simmering.
oSlow warming.
3 - 4 oReheating.
oRapid simmering.
oCooking rice.
5 - 6 oCooking pancakes.
7 - 8 oSautéing.
oCooking pasta.
9 oStir-frying.
oSearing.
oBringing soup to the boil.
oBoiling water.
The boost function
To obtain a faster and more powerful heating speed, the power
booster function can be used for the top cooking zones.
oPress the zone selection button of one of the top zones
(B) or (C).
oThen press the booster button. The cooking zone indicator
will show “P” to indicate that the function has been
activated.
The boost function will operate the zone at maximum power for 10
minutes. After this time, the cooking zone will return to its original
power setting. The booster function can only be used on the back
cooking zones (Zone B = 1.40 kW induction zone +booster = 1.80 kW.
Zone C = 2.30 kW induction zone +booster = 3.00kW).
oThe booster function can be de-activated by selecting the
relevant zone and then pressing either the booster button again,
or by selecting a new temperature from 1 – 9 on the control
panel by using the minus button.
15

Switching off a zone
oPress the cooking zone selection button of the cooking zone that
you want to switch off.
oPress and hold down the minus button until the number in the
cooking zone indicator reaches “0”. Alternatively you can press the
plus and minus buttons simultaneously to reset the zone to “0”.
oAfter a few seconds, the cooking zone will switch off.
oA “H” and “0” symbol will flash alternatively in the cooking zone
indicator until the surface has cooled down to a safe temperature
(see the section on the “residual heat indicator” for further
information).
Switching the hob off
Once you have switched off all of the cooking zones, you should switch
the hob off. oPress the ON/OFF button.
oIt is possible to turn the hob off at any time by
pressing the ON/OFF button.
Residual heat indicator
oAfter a zone is switched off, the corresponding
cooking zone indicator will show a letter “H” (HOT)
and “0” (OFF) flashing alternatively. This means
that the temperature of the zone is over 60°C and
is therefore still high enough to cause injury.
oIMPORTANT: The residual heat indicator will disappear if your
mains supply is cut. Care should be taken in case the surface
temperature is still high.
16

Pan sensor
Each zone has a sensor on it, so it can detect the presence of a pan.
oThe sensor is fine-tuned to detect a pan being placed on it. The
pan should be one size smaller than the nominal diameter of the
zone. oIf after placing a pan on a cooking zone and
selecting that cooking zone, a “U” shaped symbol
appears on the cooking zone indicator, this means
that the pan is either the incorrect size or shape.
Or it could be made from a material that is inappropriate for use
on an induction zone hob.
oIf a cooking zone is selected but no pan is detected, the pan
sensor system will check for the presence of a pan
approximately every few seconds. If no pan is detected after 2.5
seconds the hob will automatically switch off
oYou should check that your pans are suitable for use on an
induction zone hob (see the pan manufacturer’s trademark or
instructions).
Cookware that is suitable for an induction hob
The table below shows cookware that is normally suitable for use on
an induction zone hob:-
Cookware Suitable
Steel, enamelled steel Yes
Cast iron Yes
Stainless steel Yes (if stated by the pan
manufacturer)
Aluminium, copper, brass No
Glass, induction, porcelain No
oThe bottom of the pans should be as flat and thick as possible.
oCertain types of cookware may result in a noise being made
when being used on an induction zone hob. This does not mean
that there is an appliance fault.
oIMPORTANT: You should make sure that all pans are placed in
the centre of the induction zone that you are using.
17

The hob timer (minute minder)
Your hob has a timer which will countdown a period of time between 1
and 99 minutes. At the end of the countdown period an audible signal
will sound. No induction zone can be in use while using the
minute minder.
oPress the ON/OFF button to turn the hob on.
oPress the timer button to enter the minute minder
setting mode. The timer indicator will flash and the
default countdown time of “00” minutes will appear in
the display.
oSet the required countdown time using the plus and minus buttons.
Each press of the plus or minus button will increase or decrease the
time by 1 minute.
oIf you press and hold the plus or minus button the time will
increase or decrease at a faster rate.
oWhen the required countdown time is shown in the display (7),
release all buttons. The display will show the remaining time and
the timer indicator will flash for a few seconds before the
countdown begins automatically.
oWhen the set countdown time has elapsed an alarm will sound for 2
minutes or until any button is pressed. The timer indicator will show
“00”.
oYou can cancel the minute minder at any time by
pressing the plus and minus buttons simultaneously.
The timer display will show “00” and the minute
minder will be cancelled.
oYou can modify the countdown timer any time by using the
plus/minus keys.
oYou can also cancel the minute minder by adjusting the countdown
timer down to “00”, or by pressing the power button twice.
18

The hob timer (linked to a cooking zone)
You are able to link a countdown time to a cooking zone so that when
the countdown time has elapsed the cooking zone will switch off
automatically.
oPress the ON/OFF button to turn the hob on.
oPress the cooking zone selection button of the cooking zone
that you want to use and place a suitable pan on the selected
cooking zone.
oSelect the power level for the cooking zone that you have selected,
using the plus and minus buttons
oPress the timer button to enter the countdown setting mode.
The timer indicator will flash and the default countdown time of
“00” minutes will appear in the display.
19
l timer.
oSet the required countdown time using the plus and minus
buttons. Each press of the plus or minus button will increase or
decrease the time by 1 minute.
oIf you press and hold the plus or minus button the time will
increase or decrease by 10 minutes.
oWhen the required countdown time is shown in the display, release
all buttons. The display will show the remaining time and the timer
indicator will flash for a few seconds before the countdown begins
automatically.
oA red dot (LED) will appear in the corner of the timer display
(7) to indicate the relevant zone associated with the hob
timer. E.g. If the bottom right LED is on, the bottom right
cooking zone has an operationa
NOTE: You can set up a hob timer for each induction cooking
zone separately, which can run simultaneously. Just follow the
steps above, using the hob selection buttons (2) to select each
hob independently. Once set, the timer (7) will display the
time/hob ending the soonest.
WARNING: If any other cooking zones are in use without the
hob timer they will continue heating. You will need to switch
them off manually when cooking is complete.
oWhen the set hob time has elapsed an alarm will sound for 2
minutes or until any button is pressed, and the cooking zone will
turn off. The timer indicator will show “00”.

oYou can cancel the hob timer at any time by selecting the
relevant zone using the selection button (2) and then
pressing the plus and minus buttons simultaneously. The
timer display will show “00” and the minute minder will be
cancelled.
oYou can modify the hob timer any time by selecting the relevant
zone and using the plus/minus keys.
oYou can also cancel the hob timer by selecting the relevant zone
and adjusting the countdown timer down to “00” using the
plus/minus buttons, or by pressing the power button twice.
Locking the hob top
It is possible to lock the controls to prevent unauthorised usage of the
controls by other persons such as children.
oThe whole hob top can be locked by pressing the front
right cooking zone selection button and the minus
button simultaneously.
oImmediately after, press the front right cooking zone
selection button only.
oThe timer display will show “L” to indicate that the safety lock
feature has been switched on.
IMPORTANT: The above operation must be completed within 10
seconds, and no other buttons can be pressed, or the hob will
not lock.
NOTE: If a zone is in the ‘hot’ condition, the display will flash
“L” and “H” alternatively, until the zone has cooled.
oWhen the safety lock feature is activated, it will disable all buttons
on the control panel apart from the ON/OFF button.
oTo disable the safety lock feature, you should press
front right cooking zone selection button and the minus
button simultaneously.
oThe “L” symbol will disappear from the timer display and you are
then able to use the hob in normal operation.
Note: If the hob is switched off using the ON/OFF button while the
safety lock is activated, the safety lock will still be activated when the
hob is turned back on.
20