Baxton Studio BECKER-FULL-DAYBED User manual

NO PART LIST QTY
BACK REST 1PC
SIDE PANEL
(L)
FRONT
SIDE RAIL
LEG
ITEM HARDWARE QTY
JCBB SCREW
M8 x 20MM
L - KEY
M5 x 65MM
1PC
1PC
4PCS
12PCS
4PCS
4PCS
4PCS
4PCS
STEP 1
STEP 3
1
2
3
4
5
BECKER-FULL-DAYBED
BECKER-QUEEN -DAYBED
6
SIDE PANEL
(R)
Please do not tighten the hardware until the entire assembly is completed.
7
8
SLAT 2 SET
JCBC SCREW
M6 x 35MM
SPRING WASHER
FLAT WASHER
(BIG)
L - KEY
M4 x 65MM
SCREW
M4 x 32MM 14PCS
1PC
1PC
A
B
JCBC SCREW
M6 x 50MM
C
D
E
F
G
H
9
7pcs
2PCS
BACK
SIDE RAIL
1PC
1PC
1PC
CENTER
SUPPORT
SUPPORT
LEG
Begin assembly by attaching each Leg (6) to the bottom of the
Side Panel (2) & (3) securing with 2 Allen Bolt (B) per panel using
L-key (G).
STEP 2
Attach the Front Rail (4) and Back Rail (5) to the Side Panel (2) & (3)
by aligning holes and securing with 2 Allen Bolts (A) per each end using
L-key (H). (DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
Attach the Back Rest (1) to each Side Panel (2) & (3) by aligning the
hole and securing with 2 Allen Bolts (C), 2 Spring Washer (D), 2 Flat
Washer (E) per each end using L-key (G) as picture below.
(DO NOT FULLY TIGHTEN BOLTS FOR THIS STEP)
STEP 4
Secure 2 Support Leg (9) to the Center Support (8) as shown on step 4.1.
Tighten the Support Leg (9) clockwise until secure. Insert the pre-set
metal on Center Support (8) to the metal bracket on each side of Side
Panel (2) & (3) as step 4.2. Then securing the metal bracket as shown in
step 4.3 with 1 Screw (F) each side using Phillips He ad Screwdriver
(NOT INCLUDED)
L
G6
B
3
R
2
3
2
4
5
A
H
3
2
4
5
1
G
F
9
CDE
3
2
4
5
3
2
4
5
3
2
4
5
STEP 4.2
STEP 4.3
3
2
4
5
1
STEP 4.1
8
8

STEP 5 STEP 6
Please do not tighten the hardware until the entire assembly is completed.
Tighten All Bolts from step 1 to step 4 by using L-key (G) & (H) that has been provided.
Attached Slat (7) to Front Side Rail (4) & Back Side Rail (5) by unrolling and securing
with 6 Screw (H), per set using Phillips Head Screwdriver. Securing Slat (7) to Back Side
Rail (5) with 2 Screw (F) as step 5.1. Following by step 5.2, using 1 Screw (F) to secure
Slat (7) to Front Side Rail (4). Repeat the same step to attach another set of Slat (7).
STEP 5.1
ASSEMBLY
COMPLETE
3
2
4
1
7
F
STEP 5.2
7
F