BCP SKY5287 User manual

SKY5287Ver. 1
INSTRUCTION
MANUAL
10-foot x 10-foot Pergola

Please retain these instructions for future reference.
HARDWARE
19
68 PCS
M6 x 15mm SCREW M6 x 45mm SCREW M6 x 65mm SCREW
20
32 PCS
21
6 PCS
M4 NUT
22
30 PCS
23
5 PCS
M4 x 25mm SCREW EYE BOLT EYE BOLT/WHEEL
24
5 PCS
25
19 PCS
M4 x 10mm SCREW
26
30 PCS
27
1 PC
EYE BOLT/PLATE STRING
28
1 PC
TOOLS REQUIRED
APPROXIMATELY
120 MIN.
ASSEMBLY
NOTICE
•Firmly secure all bolts, screws and knobs before use.
•Reconfirm that all bolts, screws, and knobs are secure every 90 days.
•Fasten screws loosely during assembly. Do not firmly tighten screws until item is fully assembled.
•Do not use or store this item in the proximity of open flame or flammable/combustible chemicals.
•Be aware that some parts are heavy and have sharp edges.
•If any parts are missing, broken, damaged, or worn, stop using this product until repairs are made
and/or factory replacement parts are installed.
•Do not use this item in a way inconsistent with the manufacturer’s instructions as this could void the
product warranty.
2|
ALLEN WRENCH
(2, PROVIDED)
2 PERSON
ASSEMBLY
SMALL
WRENCH LADDER
DRILL

PARTS
1 PC
SHORT REAR FRAME
3 PCS 3 PCS 1 PC
MIDDLE FRAME I
56MIDDLE FRAME II 7LEFT FRAME I 8
1 PC
LEFT FRAME II
1 PC 1 PC 5 PCS
RIGHT FRAME I
910 RIGHT FRAME II 11 TRACK 12
1 PC
COLUMN WITH HOOK
1 PC 5 PCS 5 PCS
LONG REAR FRAME
13 14 ROOF FRAME I 15 ROOF FRAME II
16
7 PCS
CONNECTING PLATE
17
| 3
1 PC
COLUMN I
2 PCS 1 PC 1 PC
COLUMN II
12LONG FRONT FRAME 3SHORT FRONT FRAME
4
4 PCS 1 PC 1 PC
FOOT
18 COVER
29 ROOF
30

1Slide a part 17 connecting plate into a part 3 long front frame and part 4 short front frame.
Attach the front frame pieces to the connecting plate with eight part 19 screws.
Repeat with the part 5 short rear frame and part 14 long rear frame.
2Attach the rear frame to a part 1 column I and part 2 column II with eight part 20 screws.
4|
PRODUCT ASSEMBLY
17
3
5
1
2
4
14
x16
x2
19
x8
20
5
14

3Attach the front frame to a part 2 column II and part 13 column with hook with eight part 20 screws.
PRODUCT ASSEMBLY
4
4
3
213
x8
20
| 5
12
9
8
Slide a part 17 connecting plate into a part 8 left frame I and part 9 left frame II.
Attach the left frame pieces to the connecting plate with eight part 19 screws.
Attach a part 12 track with six part 26 screws.
Repeat with the part 10 right frame I and part 11 right frame II.
x12
x2
26
x16
19
17
x2
10
11

6|
5
PRODUCT ASSEMBLY
Carefully stand the front/rear frames up. Attach the
left frame and right frame with sixteen part 20 screws.
Attach four part 18 feet with eight part 19 screws.
18
x16
20
x8 x4
19
12
x18
26
6Slide a part 17 connecting plate into a part 6 middle frame I and part 7 middle frame II.
Attach the middle frame pieces to the connecting plate with eight part 19 screws.
Attach a part 12 track with six part 26 screws.
Repeat to build an additional two middle frames.
17
7
6
x24
x3
x3
x3
x3
19

| 7
7Attach the three middle frames with six part 21 screws.
PRODUCT ASSEMBLY
8Slide five part 15 roof frame I into five part 16 roof frame II.
x6
21
16
x5
15
x5

8|
9Attach five part 24 eye bolts to a roof frame with five part 22 nuts.
Attach fifteen part 25 eye bolt/wheels to three roof frames fifteen part 22 nuts.
Attach four part 25 eye bolt/wheels and a part 27 eye bolt/plate to a roof frame with five part 22 nuts.
PRODUCT ASSEMBLY
10 Secure the five roof frames to the part 30 roof with the attached adhesive strips.
Arrange roof frames according to the following diagram:
27
24
30
x5
22
x25
25
x19

| 9
11 Insert the wheels into the tracks on the left, right, and three middle frames to attach the roof.
Secure the five part 24 eye bolts to the frames with five part 23 screws and five part 22 nuts.
PRODUCT ASSEMBLY
x5
23
x5
22
24
x5

10 |
12 Tie the part 28 string to the part 27 eye bolt/plate.
Follow steps to route the string through the pulleys:
PRODUCT ASSEMBLY
INSIDE VIEW
INSIDE VIEW
2
1
6
3
4
5
7
Tie the end of the
string back onto
the eye bolt/plate.