BCP SKY2424 User manual

SKY2424
Ver. 2
INSTRUCTION
MANUAL
Double Door Digital Safe Box

GUN SAFETY
Treat every weapon as if it
were loaded.
Never point weapon at
anything you do not intend
to shoot.
Always keep the weapon’s
safety lock on until you
intend to fire.
Keep finger pointed
straight and o the trigger
until you are ready to fire.
bestchoiceproducts.com

Please retain these instructions for future reference.
| 3
4 PCS
OVERRIDE KEY
PARTS
A
HARDWARE
1
4 PCS
M7 x 79mm
SLEEVE
ANCHOR
TOOLS REQUIRED
•This is not a toy. Do not allow children to operate this item.
•This item is intended for indoor, household use only.
•Place item on a stable and level surface.
•Do not stand on or use any part of this product as a step ladder.
•Firmly secure all bolts, screws and knobs before use.
•Reconfirm that all bolts, screws, and knobs are secure every 90 days.
•Be aware that some parts are heavy and have sharp edges.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
•If any parts are missing, broken, damaged, or worn, stop using this product until repairs are made
and/or factory replacement parts are installed.
•Do not use this item in a way inconsistent with the manufacturer’s instructions as this could void the
product warranty.
NOTICE
8 AA BATTERIES
(PROVIDED)
+AA -
HAMMER
DRILL
SOCKET
WRENCH
FOR SECURING SAFE
11MM
SOCKET
11

CONTROL PANEL
DIAGRAM
4|
TOP SAFE RESET BUTTON (RED)
BOTTOM SAFE
SUCCESS INDICATOR
(GREEN)
OVERRIDE KEYHOLE
ERROR INDICATOR
(RED) KNOB
KEY NUMBER
LABEL
BATTERY COMPARTMENT
Install 4 AA batteries
KEYPAD
CONTROL PANEL
BOLTS

Before first use, use override key to open the safe.
1. Open the battery compartment. If necessary, remove batteries to access the override keyhole.
2. Insert an override key into the keyhole and turn counter-clockwise.
3. While holding the key in position, turn the knob clockwise to open the safe.
4. Remove the key and keep it in a secure location.
NOTE: Do not store keys inside the safe.
You are required to program two codes per safe.
1. With a safe open, press the reset button behind the door, then press the Start button. The display will
show “------” to indicate it is ready to receive a code.
2. Enter a six-digit code. The display will show “IN” to indicate the code is received.
3. Press the Start button and the display will show “------” to indicate it is ready to receive a second code.
4. Enter a dierent six-digit code and press the reset button. The display will show “IN” to indicate the
code is received.
5. Repeat to program codes for the other safe.
OVERRIDE KEY
PROGRAMMING CODES
| 5
OVERRIDE KEYHOLE
RESET BUTTON

OPERATING INSTRUCTIONS
Basic Security:
1. Press Start button and display will show “------".
2. Input one of the two possible codes. The green indicator light will turn on.
3. Turn knob clockwise to open safe.
Advanced Security:
1. Press Start button and display will show “------".
2. Input first code. The display will show “PASS”.
3. Input second code. The display will show “OPEN” and the green indicator light will turn on.
4. Turn knob clockwise to open safe.
If wrong code is entered, the display will show “ERROR” and the red indicator light will turn on.
LOW BATTERY
• To test battery level, press the Start button. If batteries are low, display will show “LOBAT”. Replace the
batteries immediately.
• After replacing batteries, display will show “GOOD”.
Basic Security: The lock is unlocked by one (of two) codes.
To set basic security mode, do the following:
1. Press Start button, then press the 1 key. The display will show “1-----“.
2. Press the reset button. The panel will beep and display will show “SINGLE” to indicate the basic
security mode is set.
Advanced Security: The lock is unlocked by two codes entered in succession.
To set advanced security mode, do the following:
1. Press Start button, then press the 2 key. The display will show “2-----“.
2. Press the reset button. The panel will beep and display will show “DOUBLE” to indicate the advanced
security mode is set.
SECURITY MODES
6|

| 7
1/4 inch
SECURING SAFE
To secure the safe, use four part 1 sleeve anchors to attach the safe to a concrete wall or floor.
1. Drill four holes into the wall/floor.
-NOTE: Drill approximately a ¼” deeper than the length of the sleeve anchor.
2. Insert four sleeve anchors into the holes.
-NOTE: Use a hammer if necessary.
3. Tighten the nuts to secure the safe to the wall/floor.
1x4
TROUBLESHOOTING
REASON
Not opening correctly
PROBLEM
Cannot unlock with
override key
Forgot code
Entered code but
cannot open safe
SOLUTION
Turn key counterclockwise while turning
knob clockwise
-Use override key to open safe
-If basic security mode, try the other code
Buttons not fully pressed Firmly press buttons
Advanced security mode
requires two codes Enter the second code
Wrong code Re-enter code

All items can be returned for any reason within 60 days of the receipt and will receive a full refund as long
as the item is returned in its original product packaging and all accessories from its original shipment are
included. All returned items will receive a full refund back to the original payment method. All returned
items will not be charged a re-stocking fee.
All returned items require an RA (Return Authorization) number, which can only be provided by a Best
Choice Products Customer Service Representative when the return request is submitted. Items received
without an RA may not be accepted or may increase your return processing time. Once an item has been
received by Best Choice Products, refunds or replacements will be processed within 5 business days.
All returns must be shipped back to the Best Choice Products Return Center at the customer’s expense. If
the reason for return is a result of an error by Best Choice Products then Best Choice Products will provide
a pre-paid shipping label via email. Boxes for return shipping will not be provided by Best Choice Products,
and is the customer’s responsibility to either use the original shipping boxes or purchase new boxes.
Pictures may be required for some returns to ensure an item is not damaged prior to its return. Items
returned are not considered undamaged until they are received by Best Choice Products and verified as
such. All damages to items are the customer’s responsibility until the item has been received by and
acknowledge by Best Choice Products as undamaged.
PRODUCT WARRANTY INFORMATION
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or
loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, or neglect of this product.
HELP CENTER
Product Assembly
Product InquiryChat Support Returns & Refunds
Orders FAQ
WARNING
Question about your product? We're here to help. Visit us at:
help.bestchoiceproducts.com
CHAT
US!