BCP SKY6209 User manual

SKY6209Ver. 2
Collapsible Treadmill
INSTRUCTION
MANUAL

As shoppers, we’re always trying
to find the perfect balance between
quality & value. At BCP, we believe
we’ve achieved that. Our diverse
catalog of everyday essentials is
tailored especially to our customers
& guaranteed to hit that sweet
spot of high quality & low price.
Always.

| 3
•Keep children and pets away from this machine at all times.
•Reconfirm that all bolts, screws, and knobs are secure every 90 days. May vary depending on how often
you use this item.
•Position this machine on a clear, level surface.
•Always wear appropriate workout clothing when exercising. Running or aerobic shoes are also required.
•Use the provided tools or suitable tools of your own to assemble the machine or repair any parts of
the machine.
•Use only original spare parts for any necessary repairs.
•Read all instructions before use.
•This machine is intended for home use only, not suitable for therapeutic purposes.
•This machine has an adjustable running belt, do not use unless the belt is secure.
•If any parts are missing, broken, damaged, or worn, stop using this product until repairs are made
and/or factory replacement parts are installed.
•Do not use this item in a way that is inconsistent with the manufacturer’s instructions as this could void
the product warranty.
•This product contains small parts for assembly. Keep small children and pets away during assembly.
•This product has a weight capacity of 220lbs. Please do not exceed that weight limit, as this could
result in personal injury and property damage.
•Do not leave unattended children in the same room with the machine.
•Do not use near water, outdoors, or in direct sunlight.
•Consult with your physician or healthcare professional before starting any workout program.
•Do not stand on the running belt before it starts moving.
•Do not start the machine while it is folded.
•Do not wear loose clothing that might catch on any part of the treadmill while in use.
•Do not place the treadmill in area that will block any vents or air openings.
•Do not put any objects on the machine.
•Do not set treadmill or plug near heated places or open fire. Leave a 6-foot clearance of all heat vents,
fireplaces, and other sources of heat.
•Please switch o all functions and pull out plug after each use.
•Increase the running speed in slow increments, failure to do so may result in personal injury.
•When ending a workout, decrease speed slowly.
•Do not adjust the conveyor belt while in motion.
•Clip the safety key onto your clothing during use.
•If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, stop the
workout, and consult a physician immediately.
•Do not place any sharp objects around this machine.
•This product contains moving parts, avoid obstructing. Do not touch parts while they are in motion as
this may result in personal injury.
•To avoid physical injury, it is highly recommended that you stretch before and after every exercise
session.
•Handicapped or disabled persons should not use this machine without the presence of a qualified
health professional or physician.
Please retain these instructions for future reference.
NOTICE
WARNING

4|
HARDWARE
1
4 PCS
D-WASHER M8 WASHER
2
2 PCS
M8 x 16mm
SCREW
3
6 PCS
M16 x 55mm
TENSION KNOB
4
1 PC
TOOLS REQUIRED
UP TO 30 MIN.
ASSEMBLY
1 PERSON
ASSEMBLY
220 LBS
CAPACITY
LBS
WRENCH
(PROVIDED)
ALLEN WRENCH
(PROVIDED)
SILICONE OIL
(PROVIDED)
5
1 PC
M12 x 20mm
FIXED KNOB 6
1 PC
SAFETY KEY 7
2 PCS
M6 x 25mm
SCREW 8
2 PCS
M6 NUT
CALIFORNIA PROPOSITION 65
WARNING: This product can expose you to chemicals including Di(2-ethylhexyl) phthalate (DEHP), which
is known to the State of California to cause cancer and birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
SPARE HARDWARE
1
2 PCS
D-WASHER M8 x 16mm
SCREW
3
2 PCS
7
2 PCS
M6 x 25mm
SCREW
8
2 PCS
M6 NUT
NOTE: These hardware are already attached to the parts for safety and ease transport. Please consider
them spare hardware.

| 5
PRODUCT ASSEMBLY
1
8x2
7x2
BA
Locate and unscrew the pre-assembled hardware on the part A console.
Interlock the part A console to the part B running deck by connecting the power wires in the
side support bars and the console bottom.
Slighty raise the side support bars on the part B running deck, then secure part A console with
the pre-assembled hardware.
NOTE: These fastenings are already attached to the frame for safety and ease transport. Please
consider them spare parts in the count of parts 7 & 8 respectivly.
PARTS
1 PC
CONSOLE
A
1 PC
RUNNING DECK
B

6|
PRODUCT ASSEMBLY
3Locate and unscrew the pre-assembled hardware on the part B running deck.
Pull the part A console into the upright position and secure it to the support bars with
pre-assembled hardware.
NOTE: These fastenings are already attached to the frame for safety and ease transport. Please
consider them spare parts in the count of parts 1 & 3 respectivly.
7x2
1
3x2
x2
2Raise the side support bars on the part B running deck into the upright position, then secure
with four part 3 screws, two part 1 d-washers, and two part 2 washers.
1
2
3x4
x2
x2

| 7
PRODUCT ASSEMBLY
4Insert the part 4 tension knob into the tab on the support bar, insert the part 5 fixed knob into
the part B running deck, then insert the safety key into the indicated slot on the part A console.
5
4

8|
FOLDING & UNFLODING THE TREADMILL
TECHNICAL SPECIFCATIONS
BLUETOOTH SETUP
FOLD:
1. Turn o the machine completely.
2. Loosen the part 5 fixed knob on the running deck and lift the running deck into the upright position.
3. Tighten the part 4 tension knob on the side support bar to secure the running board in place.
UNFOLD:
1. Make sure the machine is turned o.
2. Unscrew the part 4 tension knob and gently lower the running board.
3. Tighten the part 5 fixed knob to secure the running deck.
4
5
Voltage
Frequency
Power
Speed
Net Weight
120V
60Hz
1100W
0.5 - 7.5MPH
65LBS
•Turn the treadmill on to make the speakers discoverable
to your device under the name: BT-MUSIC
•On the device you want to pair with the speakers, open
Bluetooth Setting (reference device manual to locate),
find and select BT-MUSIC

| 9
CONSOLE INSTRUCTION
DURING USE
PROG.
START STOP
MODE SPEED
Caution!
To avoid Injury, stand
on the side rails before
starting the treadmill
Caution!
Remove the safety key when
the treadmill is not in use
Keep children away from the
treadmill at all times
SPEED
Before use, connect the machine to power then turn the switch at the front of the base frame.
•START: Press START key and the machine will start at 0.5MPH after 3 seconds.
NOTE: Make sure the safety key is on the panel before use.
•STOP: When in use, press the STOP key to put the machine into the PAUSE status.
•(+)/(-): Press the +key to increase the running belt speed, and the -key to decrease the belt speed.
The lowest speed is is 0.5 MPH and the highest 7.5 MPH.
•MODE: Press the key to set the Time, Distance, and Calories. The scan light will cycle between the three
displays every 5 seconds.
•PROG: Press the key during the standby phase to open the preset workout programs (P1-P12). Press the
key until you select your desired program.
•During the automatic programs, the (+) & (-) keys are not active. To exit the program mode, press the
STOP key or remove the safety key. Restart the machine and select your desired speed.
•For an emergency stop, remove the safety key. The screen will display Err, insert the key again to turn
the machine o.
•Place both hands on the heartrate monitors and grip firmly during your workout to receive a
heartrate reading.

10 |
RUNNING BELT ADJUSTMENT
RUNNING BELT DEVIATE TO THE LEFT
1. Start the machine at 1-1.5 miles/hour, use Allen
wrench to screw the bolt 1/4 turn clockwise.
Keep the machine running for 1-2 minutes to
until satisfactory.
2. Repeat the previous step if more adjustment is
needed, until the belt moves to the center.
RUNNING BELT DEVIATE TO THE RIGHT
1. Start the machine at 1-1.5 miles/hour, use Allen
wrench to screw the bolt 1/4 turn clockwise.
Keep the machine running for 1-2 minutes to
until satisfactory. Keep the machine running for
1-2 minutes to gauge.
2. Repeat the previous step if more adjustment is
needed, until the belt moves to the center.
RUNNING BELT SLIPPING
1. If the running surface is slipping, tighten bolts
on both ends 1/2 turn clockwise with the allen
wrench. Repeat if until the belt is
properly adjusted.
RUNNING BELT LOGJAM
1. If the running belt is not turning, loosen bolts
allen wrench to turn the screws 1/2 circle both
left and right until the issue is resolved.
SILICON OIL APPLICATION
1. Slightly lift the running belt at the back and apply silicon oil to the surface underneath and on top of
the running deck.
2. Start the machine and let it run for 3 minutes to spread the oil evenly.
NOTE: It is recommended to perform this maintenance every 30 working hours of the machine.