BE Power Equipment P2115EN User manual

96397-LJP2115EN
12.2021
2,150 PSI
OPERATOR'S MANUAL
ELECTRIC PRESSURE WASHER
MANUEL D’UTILISATION DU LAVEUSES PRESSION
MANUAL DEL OPERADOR DE LA LAVADORA A PRESIÓN

2
bepowerequipment.com
Congratulations on your purchase of a BE Power Equipment pressure washer. You can be confident that
this pressure washer is constructed and tested with optimum performance and quality in mind.
Reading this manual will help get you the best results for set-up, operation, maintenance and avoid
personal injury or damage to your machine. By knowing how best to operate this machine, you will be
better positioned to show others who may also operate the unit.
All the information in this manual is based on the latest product information available at the time of printing.
BE Power Equipment reserves the right to make changes at any time without notice or incurring any
obligation.
Owner/Operator Responsibility
The owner/operator must have a thorough understanding of the operation, maintenance and dangers
associated with using this machine. It must be understood that it is ultimately up to the owner/operator to
safely use this machine as outlined in this manual.
This manual is considered a part of the machine and needs to be kept in a safe location. If the machine is
resold or given to someone else, this manual needs to be included.
Record Identification Numbers
It is recommended that you record the product identification numbers in this manual. These numbers are
important to have on hand if you need to contact technical support (1-866-850-6662). The model and serial
number can be found on the box and on decal on the machine.
PRODUCT IDENTIFICATION
Model Number: P2115EN
Date of Purchase:
Dealer Name:

3
bepowerequipment.com
TABLE OF CONTENTS
PRODUCT SPECIFICATIONS
Product Specications.......................................................................................... 3
Package Contents ................................................................................................ 4
Hardware Contents............................................................................................... 4
Safety Information ................................................................................................ 5
Assembly Instructions........................................................................................... 7
Operating Instructions ......................................................................................... 10
Care and Maintenance ....................................................................................... 12
Pump Saver........................................................................................................ 13
Troubleshooting.................................................................................................. 14
Limited Warranty ................................................................................................ 15
Replacement Parts List ...................................................................................... 16
SPECIFICATIONS
Model Max PSI
(lbs/sq. in.)
Max GPM
(Gal/per min)
Cold
Water
Volts Frequency
(Hz)
Amps Weight (lbs.)
P2115EN 2150 1.6 ✓120 60 13 26.9

4
bepowerequipment.com
PACKAGE CONTENTSPACKAGE CONTENTS
HARDWARE CONTENTS
AA
Screws
Qty. 4
E
C
D
G
B
AA
K
PW95824
L
F
15°– Yellow
25°– Green
I
H
J
M
ON/I
OFF/O
A
D(Hose reel for
storage only)
Note: Screw is located in
package with manual.
PART DESCRIPTION QUANTITY
J Spray Gun Trigger Lock 1
K O-Ring Kit 1
L High Pressure Foam Cannon 1
M Rotary Nozzle 1
AA Screws 1
PART DESCRIPTION QUANTITY
A Power Washer Unit 1
B Spray Gun Holster 1
C Nozzle Cleaning Wire 1
D High Pressure Hose 1
ENozzle Tray 1
F Zinc Steel Lance 1
GGarden Hose Adapter 1
H Quick Connect Nozzle 2
I Spray Gun 1
Screws
Qty 1

5
bepowerequipment.com
SAFETY INFORMATIONSAFETY INFORMATION
Please read and understand this entire manual before attempting
to assemble and operate the product.
This manual contains information that relates to PROTECTING
PERSONAL SAFETY and PREVENTING EQUIPMENT
PROBLEMS. It is very important to read this manual carefully and
understand it thoroughly before using the product. The symbols
listed below are used to indicate this information.
DANGER
Potential hazard that will result in serious injury or loss of
life.
WARNING
Hazard that could result in serious injury or loss of life.
CAUTION
Potential hazard that may result in moderate injury
or damage to equipment.
Note: The word “Note” is used to inform the reader of something
the operator needs to know about the tool.
WARNING
To reduce the risk of injury, the user must read
and understand the instructions before using
this product.
1. Warning – When using this product, basic precautions should
always be followed, including the following.
2. Read all the instructions before using the product.
3. Know how to stop the product and bleed pressures quickly. Be
thoroughly familiar with the controls.
4. Keep operating area clear of persons.
5. Do not overreach or stand on unstable support. Keep good
footing and balance at all times.
6. Follow the maintenance instructions as specied in the
manual.
7. To avoid personal injury and/or damage to property and to
maximize your power washer experience, carefully follow all
of the safety tips, instructions, warnings and safeguards and
become familiar with all of the controls. Be sure you know how
to quickly bleed o󰀨 the pressure from all parts of your power
washer and how to turn o󰀨 the power washer.
8. This power washer conforms to CSA and other safety and
consumer standards. DO NOT modify or rebuild any part of
your power washer.
9. DO NOT use your power washer when you are under the
inuence of alcohol or drugs. Use this power tool carefully
and only when you are alert.
10. Watch your balance and footing while using your power
washer. Surfaces become slippery when wet and are extra
slippery when using a detergent or cleaner.
11. NEVER operate the power washer in bare feet, sandals, or
open-toed shoes.
12. When using the power washer near children, make sure they
are closely supervised by an adult to avoid injury. NEVER let
a child use the power washer.
13. Keep ngers, hands, feet and any part of your body clear of
the stream of high pressure water. The powerful spray can
cause blindness or blast holes in the skin. It can break a
window if you are too close when you pull the trigger on the
spray gun.
14. ALWAYS wear eye protection to prevent injury to eyes when
operating the power washer.
15. To avoid mishaps or injury, ALWAYS use the trigger
safety lock when not using the power washer even if
only stopping briey.
16. The power washer is equipped with a Ground Fault Circuit
Interrupter (GFCI) (For US unit only) which greatly reduces
the chance of electric shock while the unit is in use. If
replacement of the plug or cord is needed, use only identical
replacement parts.
17. Point the spray gun in a safe direction when beginning a
power washer session.
18. Warning- NEVER spray directly at a person, animal, electrical
device or the unit itself.
19. When rst using the spray gun, hold the spray gun and lance
with two hands when pulling the trigger (one hand to pull the
trigger and the other to stabilize the gun assembly) until you
get used to the “kickback” from the spray gun.
20. When you turn the power switch o󰀨, water pressure may
remain in the system. To discharge the pressure, point the
spray gun in a safe direction and pull the trigger.
21. NEVER spray ammable liquids.
22. NEVER use the power washer in areas that contain
combustible dust, liquids or vapors.
23. Avoid contact of the pressure hose with sharp objects and
examine the hose regularly. Replace if damaged. Due to
the high pressure involved, it cannot be repaired if cut or
damaged.
24. Only use detergent specically formulated for power washers
and follow instructions on the detergent’s label. Dish or
laundry soap is too thick and will
clog the nozzle of your foam cannon.

6
bepowerequipment.com
Double Insolated Product
SAFETY INFORMATIONSAFETY INFORMATION
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Servicing of a Double-Insulated Appliance
Ground Fault Circuit Interrupter Protection (For US
unit only):
This pressure washer is equipped with a ground-fault
circuit-interrupter (GFCI) built into the plugs of the
power-supply cord. This device provides additional
protection from the risk of electric shock. Should
replacement of the plug or cord become necessary,
use only identical replacement parts that include
GFCI protection.
In a double-insulated product, two systems of
insulation
are provided instead of grounding. Grounding means
are not provided for a double insulated product, nor
should grounding means be added to the product.
Servicing a double-insulated product requires
extreme care and knowledge of the system, and
should only be done by qualied service personnel.
Replacement parts for a double-insulated product
must be identical to the original parts.
A double-insulated product is marked with the words
“Double Insulation” or “Double Insulated”. Product
may also be marked with symbol shown here.
25. Protect eyes, lungs, and skin from exposure to
detergent.
26. Warning-If connection is made to a potable water
system, the system Should be protected against
backow.
CAUTION
Store the power washer indoors to prevent the
water in the unit from expanding under freezing
conditions. When the water freezes and expands,
your power washer will be damaged and become
inoperable. Or, if storing outdoors, it is
recommended you use pump saver (not included)
to protect pumps.
27. NEVER use hot water with your power washer. It will
overheat and damage the high pressure pump.
28. NEVER leave the power washer unattended while it is
powered “ON”.
29. ALWAYS turn the water supply on before turning the power
washer power to on. Running the pump dry will cause
damage to the internal components.
30. NEVER use a water supply to your power washer that
exceeds 150 PSI maximum.
31. NEVER disconnect the high pressure hose from the power
washer while the system is pressurized.
32. NEVER permanently engage the trigger mechanism on the
spray gun.
33. NEVER operate the power washer unless all components
are properly and securely connected.
34. NEVER allow the power washer pump to run for more than
one minute after you have turned o󰀨 the water supply. This
can cause the motor and pump to overheat and fail.
35. NEVER use lances or other parts that are not compatible for
this specic unit.
36. NEVER use an extension power cord since it defeats the
e󰀨ectiveness of the GFCI (For US unit only) and increases
the chance of electrocuting the operator.
37. NEVER spray any electrical outlet with your power washer.
38. Inspect the power cord before using. DO NOT use it if it is
damaged.
39. Stay alert - watch what you are doing.

7
bepowerequipment.com
PREPARATION
Before beginning assembly of product, make sure
all parts are present. Compare parts with package
contents list and hardware contents list. If any part is
missing or damaged, DO NOT attempt to assemble
the product.Please call customer service at 1-866-
850-6662 for assistance.
Estimated Assembly Time: 5 minutes.
Tools Required for Assembly (not included): Phillips
screwdriver.
ASSEMBLY INSTRUCTIONS
PREPARATION
Power Unit Assembly
Slide the spray gun holster (B) onto left side, when
facing the power washer unit (A).
1
B
A
Screw x 1
AA
AA
Screw
Qty. 2
2
A
E
AA
Slip tab into slot and screw the nozzle tray (E) on
bottom left, when facing the power washer unit (A).
Secure with screw (AA).
Note: DO NOT use a power screwdriver. When the
screw is completely tight, give a small nal clockwise
twist of the screwdriver. DO NOT overtighten.
Note: When placing the gun with the lance attached,
the nozzle will rest in this tray.
Hardware Used:

8
bepowerequipment.com
3
A
D
High Pressure Hose Assembly
Screw high pressure hose (D) clockwise onto bottom front of
power washer unit (A). Pull back collar and insert o-ring post
into water outlet far enough so collar can thread onto outlet
threads until hand tight. If it takes fewer than six turns you have
not properly tightened the high pressure hose tting. It is easier
to position the power washer in front of you to ensure that the
threads are started correctly. Failure to properly tighten high
pressure hose will result in the hose slipping or popping o󰀨
immediately upon turning unit on. Do not worry about damage if
this occurs–just reinstall and take extra care when screwing on
the high pressure hose tting.
Note: DO NOT use pliers or locking pliers to tighten.
Pull back on collar at the other end of the high pressure hose
(D). Push rmly to connect hose to spray gun (I). Twist collar to
secure. Conrm hose is locked into spray
gun by slightly pulling on them. The hose is now
securely attached to spray gun.
Twist collar then pull back to release the the high
pressure hose (D) connection from the gun (I).
Locking Spray Gun (Before Lance Installation)
To lock trigger of spray gun (I), point gun away
from you and turn dial to lock (“3” and “9” position).
Squeeze or pull trigger to make sure it is locked.
ALWAYS leave in locked position when not in
use. This ensures the gun is in “safe” mode until it
is ready for use. Turn dial to unlock (“12” and “6”
position) to release spray gun trigger.
Note: The trigger lock prevents trigger from being
accidentally engaged.
ASSEMBLY INSTRUCTIONS
3
2
4
I
D
1
D
1
3
5
I
D
3
2
D
6
1
I
Unlocked Locked

9
bepowerequipment.com
ASSEMBLY INSTRUCTIONS
10
A
G
Garden Hose Adapter Installation
Attach collar of garden hose adapter (G) directly to
power washer water inlet (A). Hand tighten.
Extension Lance Installation
While the spray gun (I) is in the locked position, insert
the extention lance (F) into the end of the spray gun,
by inserting and pushing together turning clockwise
simultaneously. To remove, push together and turn
counterclockwise.
Note: Always push the safety lock button to lock the
trigger when changing lances to ensure that they do
not accidentally eject with force during removal.
Attach nozzles (H), rotary nozzle (M) or foam cannon
(L) into end of lance (F) by pressing selected nozzle
into place. It will make a “click” sound when rmly in
place.”
Note: Always turn the safety lock dial to lock trigger
when changing lances and nozzles to ensure that
they do not accidentally eject with force during
removal.
1
2
9
F
H
M
L
To remove nozzle (H), rotary nozzle (M) or foam
cannon (L) pull back on collar of lance (F) and pull
out nozzle.
2
1
7
F
I
8
F
H
M
L

10
bepowerequipment.com
Attach garden hose to the garden hose adapter (G).
Note: Flush out garden hose before connecting
to garden hose adapter.
1
11
G
ASSEMBLY INSTRUCTIONS
OPERATING INSTRUCTIONS
OFF/0
ON/I
OFF/0
ON/I
• Turn the power switch to the “ON” (|) position. The unit will turn
on for 1 - 2 seconds and shut o󰀨. This is a normal function of
the auto start feature. Squeeze the spray gun trigger to begin
pressure washing.
• Begin power washing by squeezing the trigger on the spray gun
all the way into the handle.
• Release the spray gun trigger to stop the power washer.
• Allow the motor to come to a complete stop before squeezing
the trigger again.
• Squeezing rapidly will cause the auto start feature to miss an
on/o󰀨 cycle that may prevent it from turning on while squeezing
trigger after rapid squeezing. Use slow deliberate trigger pulls to
avoid such symptoms.
• Always test a small area to avoid chance of damaging the
surface.
• Make sure the “ON/OFF” switch is in the “OFF” position. The
power switch has international symbols for ‘on’ and ‘o󰀨’: On
(|) O󰀨 (O).
• Unwind the power cord completely and plug the GFCI (For
US unit only) into a grounded 120 volt outlet.
• Turn on water supply at the faucet to completely
open.
• Release safety push trigger lock up and back into trigger.
While pointing the spray gun in a safe direction, squeeze
the trigger on the spray gun until there is a steady stream of
water, letting the water and air out of the hose. Push trigger
lock back down to lock back into place.

11
bepowerequipment.com
OPERATING INSTRUCTIONS
1
2
3 3
Attach Foam Canon (stored in rear of pressure washer) into end
of lance by pressing cannon into place.It will make a “click” sound
when rmly in place.
Note: Always lock spray gun when changing the foam cannon to
ensure it does not eject with force.
• When using the foam cannon, ll it with a properly formulated
detergent or cleaner with water ratio according to instructions
on the container.
• DO NOT use thick gel-like detergents as they will clog the foam
cannon and can cause damage.
• The power washer will pull a ratio of water to detergent of 10:1 or
10 parts water to 1 part detergent. The detergent concentration
can be adjusted by turning the detergent knob on the top of the
cannon. Turn it left for more concentration or turn it right for less
concentration.
Operation Tips
• Note: Test the GFCI (For US unit only) before each use:
1. Plug GFCI into power outlet. Indicator should turn green to
show that cord has power.
2. Press test button, green indicator should turn o󰀨 to verify
that GFCI cut o󰀨 power to the cord.
3. Press reset button – green indicator should turn on to
show that cord has power again.
4. When GFCI is working properly, green indicator will turn
on when power is applied. If green indicator turns o󰀨, it has
detected electric leakage and the GFCI cut o󰀨 power to
theappliance.
Using Power Cord
• Easily remove the power cord from side of unit by swiveling the
bottom red cord hook to the right or left until it faces up. The
power cord then can be easily slid o󰀨 of the side of the power
washer unit.
• Swivel red cord hook back down when ready to wrap the cord
back into place for storage.
• If you hear the motor run intermittently when the trigger is not
being squeezed, that is normal.
The pump is priming itself so it is ready to operate when the
trigger is squeezed. Turn o󰀨 the power washer if not being
used after ve minutes.
• The o-rings on the bayonet end of the nozzle lance should be
cleaned regularly and lubricated with non-water soluble grease
such as petroleum jelly.
• Keep the nozzle cleaning wire for use in unclogging the nozzle.
If you lose the cleaning wire, astraightened paper clip also
works.
How to Avoid Damaging Surfaces
• Damage to surfaces being cleaned occurs because the impact
force of the water pressure exceeds the durability of the
surface. Bare wood can be penetrated; paint can be peeled
o󰀨, etc. You can vary the force of your power washer by
controlling:
1. The angle of the surface being cleaned.
2. The distance of the nozzle from the surface being
cleaned.
• NEVER use a narrow high pressure stream of water on soft
surfaces susceptible to damage.
• Use the 25° quick connect nozzle when cleaning windows.
Squeeze the trigger and vary the spray pattern and angle until
optimum cleaning e󰀩ciency is achieved.

12
bepowerequipment.com
OPERATING INSTRUCTIONSCARE AND MAINTENANCE
Detergents
• Use detergents designed for power washers.
Hardware stores or home centers also have power
washer detergents for di󰀨erent cleaning projects.
The cleaning solution should be the consistency of
water in order to prevent clogging your detergent
bottle and nozzle.
• This system applies detergent under low pressure.
The cleaning power of the detergents is enhanced
when applied with low pressure and enough
time is given to break down dirt and grime. The
combination of low pressure and chemical action
is very e󰀨ective and can be better than scrubbing
if applied properly. ALWAYS spray detergent on a
dry surface. DO NOT pre-soak area. Wetting the
surface rst dilutes the detergent and reduces its
cleaning ability. DO NOT allow detergent to dry
on surface. On vertical surfaces being cleaned,
apply detergent to lower surfaces and work your
way up to prevent detergent from causing streaks
in the dirt and grime. Rinse detergent by pressure
washing from bottom up for same reason.
• If a stain is particularly tough, it may be necessary
to reapply the detergent and use a bristled brush
to scrub the stain. Subsequent power washing
after brushing should successfully complete your
cleaning job.
Cleaning Garden Hose Adapter
• The screen inside the adapter should be cleaned
periodically. Remove it by dragging a thumb over
the screen with enough pressure to pull the screen
and washer out. Rinse it with clean water and then
place it back in the adapter.
Cleaning Nozzles
• A clogged or partially clogged nozzle can cause
signicant reduction of water pressure coming out
of the nozzle and/or cause the unit to pulsate while
spraying.
• Turn o󰀨 the unit.
• Turn o󰀨 the water supply to the unit.
• Relieve any pressure trapped in the hose by
squeezing the trigger 2-3 times, and then lock the
spray gun by pushing the lock button from left to
right.
• Remove the lance from the spray gun.
• Using the nozzle tip cleaner provided (or an
unfolded paper clip), insert the wire into the nozzle
hole and move back and forth until debris is
dislodged.
• Tap quick connect end of lance on hard surface
several times.
• Back ush water through the nozzles using garden
hose and highest pressure available (either
standard water nozzle or use your thumb over the
nozzle to create water pressure for back ush).

13
bepowerequipment.com
OPERATING INSTRUCTIONSCARE AND MAINTENANCE
PUMP SAVER
Pump Saver is a product that protects and prolongs
the life of the pump. This will keep the internal parts
of the pump lubricated and protected from freezing
while being stored in ALL climates. It also assists with
protection from internal corrosion. The BE Power
Equipment part number is: 85.490.046. Purchase at a
BE Power Equipment retailer near you.
Pump Saver Instructions
Follow the previous storage instructions for your
power washer. To prevent staining, protect the surface
under the power washer from any excess uid. Wear
eye protection when using this product.
Turn unit o󰀨 and disconnect the gun before adding
pump protector. Unscrew threaded top from bottle to
remove seal and reattach threaded top to bottle.
Remove black cap from bottle.
1) Place top of pump saver bottle onto the garden
hose adapter.
2) Secure pump saver bottle by turning in a clockwise
direction.
3) Turn the power on.
4) Squeeze bottle to help it into the pump.
5) Turn power o󰀨 when pump saver exits the
machine’s water outlet.
Note: Instructions on Pump Saver Bottle are generic
and not model specic.
1
2
Storage
• When your pressure washer session has been
completed, turn o󰀨 the power switch located on
the front of the power washer. Unplug the power
cord from the outlet. Turn o󰀨 the water supply.
Pull the trigger on the spray gun 2-3 times to
drain out the excess water and to release any
remaining water pressure. Disconnect the garden
hose adapter from the water inlet. DO NOT allow
the power washer to run with no water owing
through it.
• Remove high pressure hose from spray gun.
• Remove lance from the gun. Place the gun in the
holster on the side. Lances are placed into any of
the slots in the back of the unit.
• Make sure to discard any remaining detergent
from the bottle. Residual chemical will stick to
the container which could become cotaminated,
and can cause the detergent injector to clog and
not function properly. Flush the bottle and nozzle
head with fresh water to prevent clogging.
• Hook the power cord around the cord hook on the
right side of the machine when facing it.
• The pressure hose is stored on the hose hook
located on the back of the handle.
• DO NOT store the power washer where it is
exposed to freezing temperatures unless you
use an antifreeze designed for pumps. Store the
power washer indoors to prevent the water in the
unit from expanding under freezing conditions.
When the water freezes and expands, your power
washer will be damaged and become inoperable.
Or, if storing outdoors, it is recommended you use
pump saver (not included) to protect pumps.

14
bepowerequipment.com
PROBLEM CORRECTIVE ACTION
Unit will not turn on. 1. The GFCI module on the end of the power cord must be plugged directly into an
outlet.
2. Do not use an extension cord.
3. With the GFCI Connected make sure the power switch is turned on.
Note: When power switch is turned on, the power washer will turn on by itself for 1-2
seconds and shut o󰀨. This is normal.
The high pressure
(HP) hose will
not connect/stay
connected to the
spray gun. Is this a
spray gun problem?
1. In most cases, the spray gun is not the problem. The problem is the rubber sleeve
covering the tting at the end of the high pressure hose. It has likely slipped up
toward the metal tip. To x: wiggle, twist and/or pull the rubber sleeve down until
the entire tip is visible plus an 1/8 in. of the metal tting below the tip. Now try to
insert the hose tip into the spray gun. It should “click” into place and will not come
out until the hose is released by pushing in the lever on the underside of the gun.
You may cut away the end of the sleeve with a sharp knife if unable to move the
sleeve down. Be careful not to cut or puncture the hose.
2. Do not push in the release button when connecting the high pressure hose.
The unit is running
but there is no water
ow.
1. Power should NOT be turned on until water comes through the spray gun. Doing
so will damage the motor.
2. Check the water source.
3. Eject the nozzle from the lance to determine if clog is coming from the nozzle (If
nozzle is clogged, see nozzle cleaning instructions under “Cleaning nozzles”).
4. Take o󰀨 the lance and just spray out of the spray gun. This will indicate if the
problem is with the lance.
5. Check Garden Hose Adapter for loose connection and the lter for debris.
Why is water
leaking where the
high pressure hose
connects to the spray
gun?
1. Make sure there is an o-ring at the end of the metal tip of the high pressure
hose. If no o-ring is present, the connection between the hose and spray gun will
leak. O-Ring Replacement Kit (K) is included with purchase.
I can’t remove the
lance from the spray
gun. What should I
do?
1. All lances and the detergent bottles are attached and removed from the extension
lance in the same manner. Insert the quick-release end of the lance/detergent
bottle into the extension lance. Press the extension lance and lance together
(about a 1/8”) and turn clockwise. The lance will lock in place. Remove the lance
by reversing this procedure. Press the extension lance and lance together and
turn counter clockwise. The lance will slide out.
2. Or, hold the extension lance and lance in an upright position with the nozzle end
on the oor. Push the whole assembly straight down to loosen the connection,
and then follow the removal process again. You may also spray soapy water or a
lubricant in the area where the lance connects to the extension lance.
TROUBLESHOOTING
If you have any questions regarding the product, please call customer service at 1-866-850-6662.

15
bepowerequipment.com
TROUBLESHOOTING
PROBLEM CORRECTIVE ACTION
The power washer
turns on for
2 seconds, shuts
o󰀨, and will not turn
back on. Do I have a
defective unit?
1. It sounds like your power washer is working just ne. When the water is connected,
the accessories are assembled properly, and the power switch is turned on, the
power washer may turn on for 1 - 2 seconds to prime the pump. It automatically
shuts o󰀨 and waits for the spray gun trigger to be pressed. When the trigger is
pressed, water starts owing through the pump. The water sensor in the pump
“senses” the moving water and automatically turns the power washer on.
2. Turn the power switch to o󰀨, hold in the trigger on the spray gun, so that you have
a steady stream of water. While you are holding the trigger open on the spray gun,
at the same time, turn the power switch on.
TROUBLESHOOTING
LIMITED WARRANTY
BE Power Equipment Inc. warrants the original retail purchaser that this pressure washer is free from defects
in material and workmanship for the periods set forth below. If defects are found in BE Power Equipment
products within the limitations outlined in this warranty statement, BE Power Equipment, at its sole discretion,
will repair or replace the product free of charge.
The warranty coverage is for one year and begins on the date of purchase by the end-user. Valid proof of
purchase must be presented with the warranty claim.
This warranty is limited to defects that occurred during regular operational use. This warranty does not cover
failures due to lack of service, negligence, abuse or misuse. Including, but not limited to, freezing damage,
alterations, chemical deterioration, scale build-up, rust, corrosion, thermal shock, thermal expansion,
transportation damage, oil changes, valve adjustments, fuel system maintenance or using incorrect repair
parts. Furthermore, Using the wrong fuel, water or power supply is considered a form of misuse.
This warranty also does not cover normal wearing items such as O-rings, valves, seals, lters, sparkplugs or
packings. These are considered to be maintenance items.
To obtain warranty, the claimant must take the product, with their original proof of purchase, to an authorized
BE Power Equipment service center. These service centers are located on the website:
https://www.bepowerequipment.com/service-centers
If you cannot resolve the warranty claim satisfactorily, contact the BE Power Equipment Warranty Department
(1-866-850-6662). Be prepared with details of the defect, proof of purchase,and model.
Please note: Power washers sent to the company without an RMA Number will NOT be accepted and will be
shipped back at the expense of the sender.

16
bepowerequipment.com
REPLACEMENT PARTS LIST
Printed in China
For replacement parts, call our customer service department at 1-866-850-6662, 8 a.m. - 4:30 p.m., PST,
Monday - Friday.
PART DESCRIPTION
G 25° Quick Connect Nozzle
HNozzle Tray
IGarden Hose Adapter
JGFCI Assembly (For US unit only)
K O-Ring Kit
L Gun Holster
PART DESCRIPTION
A High Pressure Foam Cannon (34 oz.)
B High Pressure Hose
C Spray Gun
D Extension Lance
E Rotary Nozzle
F 15° Quick Connect Nozzle
K
E
F
G
PW95824
A
D
B
15°– Yellow
25°– Green
IG
J
H
L
C

17
bepowerequipment.com
96397-LJP2115EN
12.2021
2,150 PSI
MANUEL D’OPÉRATEUR
LAVEUSE À PRESSION ÉLECTRIQUE
ELECTRIC PRESSURE WASHER OPERATOR’S MANUAL
MANUAL DEL OPERADOR DE LA LAVADORA A PRESIÓN

18
bepowerequipment.com
TABLE DES MATIÈRES
SPÉCIFICATIONS DU PRODUIT
Spécications du produit .................................................................................... 18
Contenu de l'emballage...................................................................................... 19
Matériel inclus..................................................................................................... 19
Consignes de sécurité........................................................................................ 20
Instructions d'assemblage .................................................................................. 22
Mode d’emploi ..................................................................................................... 25
Entretien et maintenance.................................................................................... 27
Protecteur de pompe.......................................................................................... 28
Dépannage......................................................................................................... 29
Garantie limitée .................................................................................................. 30
Liste des pièces de rechange............................................................................. 31
SPÉCIFICATIONS
Modèle PSI maximum
(k/cm2)
(lb/po2)
Débit maximum
(Litre/min)
(Gal./min)
Eau froide Volts Fréquence
(Hz)
Ampères Poids
(kg)
(lb)
P2115EN 6292
(2150)
6.1
(1.6)
✓120 60 13 12.2
(26.9)

19
bepowerequipment.com
CONTENU DE L'EMBALLAGECONTENU DE L'EMBALLAGE
MATÉRIEL INCLUS
AA
Screws
Qty. 4
Remarque : Les vis se trouvent
dans l’emballage du manuel.
Vis
Qté 1
E
C
D
G
B
AA
K
PW95824
L
F
15°– Yellow
25°– Green
I
H
J
M
ON/I
OFF/O
A
D(Hose reel for
storage only)
15°– Jaune
PIÈCE DESCRIPTION QUANTITÉ
J Verrou de la gâchette de
pistolet pulvérisateur
1
K Ensemble de joints toriques 1
L Canon mousse haute
pression
1
M Buse rotative 1
AA Vis 1
PIÈCE DESCRIPTION QUANTITÉ
A Laveuse à pression 1
B Étui à pistolet pulvérisateur 1
C Tige de nettoyage de la buse 1
D Tuyau à haute pression 1
E Bac à buse 1
F Lance d’arrosage en acier
enduit de zinc
1
G Adaptateur de tuyau d’arro-
sage
1
H Buse à raccord rapide 2
I Pistolet pulvérisateur 1
25°– Verte

20
bepowerequipment.com
CONSIGNES DE SÉCURITÉCONSIGNES DE SÉCURITÉ
Veuillez lire et comprendre tout ce manuel avant d’essayer de
monter et de faire fonctionner le produit.
Le présent manuel contient des informations concernant la
PROTECTION DE LA SÉCURITÉ PERSONNELLE et la
PRÉVENTION DE PROBLÈMES D'ÉQUIPEMENT Il est important
de lire et de comprendre l'intégralité du manuel avant d'utiliser le
produit. Les symboles apparaissant ci-dessous sont utilisés pour
indiquer ces informations.
DANGER
Risque potentiel ayant pour conséquence des blessures
graves ou la mort.
AVERTISSEMENT
Risque potentiel pouvant causer des blessures graves ou la
mort.
ATTENTION
Risque potentiel pouvant causer des blessures ou des
dommages à l'équipement.
Remarque : Le mot « Remarque » est utilisé pour informer
l'utilisateur d'un renseignement important concernant l'utilisation
de l'appareil.
AVERTISSEMENT
Pour réduire le risque de blessure, l'utilisateur doit lire et
comprendre les instructions avant d'utiliser ce produit.
1. Avertissement — Certaines précautions de base
doivent être toujours suivies lors de l'utilisation de
l'appareil, y compris :
2. Lire les instructions avant d'utiliser l'appareil.
3. Savoir comment arrêter l'appareil et le dépressuriser
rapidement. Connaître le fonctionnement de chaque bouton
de commande.
4. Dénir un périmètre de sécurité.
5. Ne pas s'étirer trop loin ou prendre place sur un support instable.
Toujours garder une position stable et sûre.
6. Suivre les directives d'entretien décrites dans le manuel.
7. Pour éviter des blessures ou des dommages matériels et
pour proter au maximum de l'appareil, suivre les conseils de
sécurité, instructions, avertissements et recommandations et
se familiariser avec les commandes.
8. Cette laveuse à pression est conforme aux normes de la
CSA et à d'autres normes de sécurité. NE PAS modier ni
reconditionner les pièces de cette laveuse à pression.
9. NE PAS utiliser cette laveuse à pression si vous êtes sous
l'inuence d'alcool ou de drogue. Utiliser cet appareil avec
prudence et uniquement lorsque vous êtes alerte.
10. Toujours garder une position stable et sûre pendant
l'utilisation de la laveuse à pression. Les surfaces mouillées
sont glissantes et l'utilisation de détergent les rend encore
plus dangereuses.
11. NE JAMAIS utiliser la laveuse à pression les pieds nus, en
sandales ou avec des chaussures ouvertes.
12. Lorsque des enfants sont présents autour de la zone
d'utilisation de la laveuse à pression, un adulte doit assurer la
surveillance pour éviter le risque de blessures. NE JAMAIS
permettre à un enfant d'utiliser la laveuse à pression.
13. Tenir les doigts, les mains, les pieds et toutes les parties du
corps loin du jet d'eau à haute pression. Le jet d'eau à haute
pression peut causer la cécité ou déchirer la peau. Il peut
fracasser une vitre si la buse est trop proche de la fenêtre
lorsqu'on appuie sur la gâchette du pistolet pulvérisateur.
14. An de prévenir les blessures aux yeux, PORTER toujours
des lunettes de sécurité pendant l'utilisation de la laveuse à
pression.
15. Pour éviter les accidents ou les blessures, VERROUILLER
toujours la gâchette à l'aide du bouton de sûreté lorsque la
laveuse à pression n'est pas en service, même si le jet a été
arrêté temporairement.
16. La laveuse à pression est équipée d'un disjoncteur de fuite
de terre an de réduire le risque de décharge électrique
pendant l'utilisation de l'appareil (Pour l’unité américaine
seulement). S'il est nécessaire de remplacer la che ou
le cordon d'alimentation, utiliser uniquement une pièce de
remplacement identique.
17. Pointer le pistolet pulvérisateur vers une direction sécuritaire
avant de commencer une séance de lavage.
18. Avertissement — NE JAMAIS utiliser le pistolet pulvérisateur
pour arroser une personne, un animal, un appareil électrique
ou la laveuse à pression.
19. À la première utilisation du pistolet pulvérisateur, tenir le
pistolet et la lance à deux mains (une main pour appuyer sur
la gâchette et l'autre pour stabiliser le pistolet et la lance) de
manière à évaluer l'e󰀨et de rebond du pistolet pulvérisateur.
20. Lorsque l'alimentation électrique de la laveuse à pression est
coupée, de l'eau sous pression demeure dans l'appareil. Pour
relâcher la pression, pointer le pistolet pulvérisateur dans une
direction sécuritaire et appuyer sur la gâchette.
21. NE JAMAIS pulvériser de liquide inammable.
22. NE JAMAIS utiliser la laveuse à pression dans un espace
rempli de poussières, de liquide ou de vapeurs combustibles.
23. Éviter tout contact entre le tuyau à HP et des objets tranchants
et vérier le tuyau régulièrement. Remplacer le tuyau s'il est
endommagé. Puisque c'est un tuyau à haute pression, il ne peut
pas à être réparé.
24. Utiliser uniquement un détergent spécialement conçu pour les
laveuses à pression et suivre les instructions sur l'étiquette de
la bouteille de détergent.
25. Utiliser des équipements de protection qui protégeront
les yeux, les poumons et la peau contre l'exposition au
détergent. Le savon à vaisselle et les détergents à lessive
sont trop épais et boucheront la buse de la bouteille à
détergent.