BEA MS41 User manual

MS41
75.5996.03 MS41 20210421 Page 1 of 4
Specifications are subject to change without prior notice.
All values measured in specific conditions.
Visit website for
available languages of
this document.
MOUNTING BOX COMPATIBILITY
SINGLE-GANG
2 ¾" H × 3 ¼" W × 15⁄16" D
DOUBLE-GANG
4 ½" H × 4 ½" W × 15⁄16" D
6” ROUND
6" H × 6" W × 1" D
SURFACE-MOUNT 10BOX24SGSM
10ABOXSGSMS
10BOXDGSM
10BOX475SQSM1
10BOX45SQSM1
10BOX6RNDSM1
FLUSH-MOUNT standard, single-gang
electrical box2
standard, double-gang
electrical box2
10BOX45SQFM1
standard, single-gang
electrical box2
Stainless steel, touchless actuator with
adjustable range and relay hold time
SINGLE-GANG
ENGLISH
4.5” SQUARE
1. Must use adapter bracket.
2. Not provided by BEA.
6” ROUND
TECHNICAL SPECIFICATIONS
Technology: microwave motion sensor
Radiated frequency: 24.125 GHz
Radiated power density: < 5 mW/cm2
Supply voltage:
to be operated from SELV-compatible
power supplies only
12 – 24 VAC ±10%
12 – 24 VDC +30% / -10%
Supply frequency: 50 – 60 Hz
Power consumption: < 1.5W
Output
relay contact rating (max. voltage):
relay contact rating (max. current):
Max. switching power:
relay with switch-over contact (voltage-free)
60 VDC / 125 VAC
1A (resistive)
30W DC / 60 VAC
Wire gauge: 26 – 22 AWG
Detection range: 4 – 24” (adjustable)
Detection mode: motion (bidirectional)
Output hold time: 0.5 – 30 sec
Temperature range: -4 – 131 °F (-20 – 55 °C)
Weight: 0.34 lbs
IP rating: IP55
*Apply silicone to sensor housing base to achieve IP65 (see page 4)*
Certification: Electromagnetic compatibility (EMC) according to 2004/108/EC
FCC: G9B-210161
IC: 4680A-210161

1
2
Page 2 of 4 75.5996.03 MS41 20210421
9When wiring multiple devices together to create a system configuration, it is best to ensure that each device works
independently. This will reduce troubleshooting if a discrepancy occurs.
9Prior to installing any equipment in either new or existing circuits, verify correct line voltage and line stability.
Always remember to shut off the power before performing circuit wiring.
9Do not place the sensor in the door’s opening range, where the sensor may see door movement.
9Do not place moving objects in front of the sensor.
INSTALLATION TIPS
WIRING
REMOVE FACE PLATE
Wire the MS41 to the door control according to the
diagram shown here.
NOTE: Use either N.O. or N.C. –not both. Refer
to the door control manual to determine which
must be used.
Detach the face plate from the cube by inserting a flathead screwdriver into one of the
snap fittings and twisting to loosen from the face plate (see image below). Repeat on
the nearby snap fitting located on the same side, top or bottom.
You may loosen the cube from the plate on either the top or bottom. Only two snap
fittings must be loosened.
empty
N.C.
N.O.
COM
12–24 VAC/VDC
12–24 VAC/VDC
PRECAUTIONS
Shut off all power going to header before attempting any wiring procedures.
Maintain a clean and safe environment when working in public areas.
Constantly be aware of pedestrian traffic around the door area.
Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the
door.
ESD (electrostatic discharge): Circuit boards are vulnerable to damage by electrostatic discharge. Before handling any
board, ensure you dissipate your body’s ESD charge.
Always check placement of all wiring before powering up to ensure that moving door parts will not catch any wires and
cause damage to equipment.
Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be performed by
BEA, Inc. Unauthorized disassembly or repair:
1. May jeopardize personal safety and may expose one to the risk of electrical shock.
2. May adversely affect the safe and reliable performance of the product resulting in a voided warranty.
Recommended:
22 –26 AWG

2
3
2
1
5
6
3 4
75.5996.03 MS41 20210421 Page 3 of 4
WIRING (cont.)
SET-UP
Six adjustments can be made to the sensor:
LED color+logic: DIP bank 1 determines LED color (see
table)
Output Mode switch: determines Toggle mode or Timer mode
= Toggle (detection activates the relay and the relay holds until a second detection deactivates
the relay (recommended for switch applications)
= Timer (detection activates the relay for 0.5 to 30 seconds; relay will hold as long as detection
occurs)
LED activity (when illuminated):
= animated (movement around track)
= standard (on, static)
Buzzer sound (when in detection):
= on
= off
Hold time potentiometer: adjust relay hold time from 0.5 to 30 seconds (rotate clockwise to increase)
Sensitivity potentiometer: adjust detection field from 4 to 24 inches (rotate clockwise to increase)
5
6
2
3
4
DIP1 DIP2 DIP3 DETECTION NO DETECTION
 blue off
 off blue
 blue blue
 green off
 off green
 green green
 blue green
 green blue
1
RETROFIT APPLICATION
You can retrofit hardwired push plates using the 900 MHZ Touchless Retrofit Transmitter
(10TD900TR) and Receiver (10RD900):
1. Locate existing 2 wires previously used for the hardwired, mechanical push plate and
connect to the MS41 terminals marked 12 – 24 VAC/VDC.
2. Wire to the transmitter's power wires (red and black) with the two MS41 power wires.
3. Wire the transmitter's white wire to COM, and green wire to N.O.
4. At the door control, move the 2 wires from the push plate activation circuit to power (refer
to Technical Specifications for power information).
5. Wire the receiver output to the door control activation circuit and its power wires shown in
step 3 above.

4
Page 4 of 4 75.5996.03 MS41 20210421
BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA,
Inc. does not guarantee any use of the sensor/device outside of its intended purpose.
BEA, Inc. strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for doors/gates, and
factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/
device system performance is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s recommendations
and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service
call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107, UL294,
UL325, and International Building Code).
Verify that all appropriate industry signage, warning labels, and placards are in place.
BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
Tech Support & Customer Service: 1-800-523-2462
General Tech Questions: [email protected] | Tech Docs: www.BEAsensors.com
Door does not open when
swiping hand in front of
sensor
Bad or no power Check power supply, ensure SELV-
equivalent power. If LED switches on or
flashes, power connections are okay.
Detection range too short Adjust detection zone. Remove any metal
plates in front of sensor.
Incorrect wiring/connection Check wiring and relay connection.
Sensor stays in detection Environmental conditions
influencing sensor
Remove moving objects from around
sensor.
Wrong output mode Switch output mode to Timer.
Door remains open after
detection/activation
Wrong output mode Switch output mode to Timer.
Incorrect wiring/connection Check wiring and relay connection.
©BEA | Original Instructions | PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING
FCC APPROVAL
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
*this device may not cause harmful interference, and
*this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
*Reorient or relocate the receiving antenna
*Increase the separation between the equipment and receiver
*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
*Consult the dealer or an experienced radion/TV technician for help
WARNING: CHANGES OR MODIFICATIONS TO THIS EQUIPMENT NOT EXPRESSLY APPROVED BY BEA INC. MAY VOID THE FCC
AUTHORIZATION TO OPERATE THIS EQUIPMENT.
INSTALLATION
1. Install an electrical box.
If using a metal eletrical box, ensure that the
sensor and related wiring does not come in
contact with the box to avoid shorting the unit.
2. Clip the MS41 cube to the face plate.
If IP65 rating is desired, apply silicone between the MS41
cube and face plate prior to installing the MS41 onto
electrical box.
3. Secure the face plate to the electrical box with the
provided screws.
electrical box
(metal/plastic)
MS41
assembly
TROUBLESHOOTING