BEA MS11 User manual

MAGIC SWITCH: MS11
12
3
75.5820.03 MS-11 20160825 Page 1 of 4
* Use of the device outside the intended application cannot be guaranteed by the manufacturer.
TECHNICAL SPECIFICATIONS
DESCRIPTION
ENGLISH
Hardwired | Stainless Steel | Touchless |
Activation Sensor
PATENT PENDING
Single Gang (shown) Double Gang Jamb Style
10MS11S 10MS11D 10MS11J
Specifications are subject to change without prior notice.
1. faceplate
2. mounting holes
3. sensor window
* Sensing Zone is dependent upon
• Size (area) of object
• Orientation of object
• Speed of object
• Environmental conditions
Technology Microwave - Doppler Radar (24.125 GHz)
Detection Mode Motion (bidirectional)
Supply Voltage 12-24 VAC/DC
Current Consumption < 2.8W
Temperature Range -22° F to 158° F
Enclosure Rating NEMA 4
Sensing Zone * 2 - 24 inches (adjustable)
Relay 1-Form C Solid State Relay
1A 30 VAC/VDC (max)
Dimensions (Overall)
[faceplate = 0.16” (T)]
Single Gang - 4.5’’ (H) × 2.75’’ (W) × 0.98” (T)
Double Gang - 4.5” (H) x 4.5” (W) x 0.98” (T)
Jamb - 4.5’’ (H) × 1.68’’ (W) × 0.98” (T)
Wire Harness Length 12 inches
Material Stainless Steel (faceplate)

1
2
PRECAUTIONS
Page 2 of 4 75.5820.03 MS-11 20160825
WIRING
Only trained and
qualified personnel
may install and setup
the sensor.
The warranty is invalid if
unauthorized repairs are
made or attempted by
unauthorized personnel.
Always test the proper
operation of the
installation before
leaving the premises.
The door control unit
and the door cover
profile must be correctly
grounded.
Description Wire Color
12-24 VAC/DC Black
12-24 VAC/DC Red
COM White
NO Green
NC Yellow
1INSTALLATION
TIPS
APPLICATIONS
single gang, double
gang, or jamb style
electrical box may be
used (non-metallic
ideal)
Single Swing Doors Dual Egress Swing DoorsSim Pair Swing Doors Sliding Doors
NOTE: Do not install the sensor within the swingpath of the door.

3
75.5820.03 MS-11 20160825 Page 3 of 4
SETTINGS & ADJUSTMENTS
DETECTION ZONE - potentiometer
COUNTERCLOCKWISE - decrease (2’’ minimum)
CLOCKWISE - increase (24’’ maximum *)
OUTPUT TIME - potentiometer
COUNTERCLOCKWISE - decrease (1 s minimum)
CLOCKWISE - increase (30 s maximum)
AUDIBLE CONTROL - 2-pin jumper
ON - jumper removed (or on 1 pin)
OFF - jumper over both pins
OUTPUT MODE - 2-pin jumper
TIMED - jumper removed (or on 1 pin)
TOGGLE - jumper over both pins
* Maximum Detection Zone will vary depending on size (area), orientation, and
speed of object as well as environmental conditions.
A
B C
FUNCTIONALITY
AUDIBLE ALERT - When Audible Alert is ON, it sounds for 0.5 seconds when detection occurs.
TIMED MODE - Recommended for automatic door applications. In Timed Mode, a detection
activates the relay and the relay holds for a predetermined amount of time adjusted by the Output
Time potentiometer (1 to 30 seconds, counterclockwise - decrease, clockwise -increase).
TOGGLE MODE - Recommended for switch applications. In Toggle Mode, a detection activates the
relay and a second detection deactivates the relay. The relay will hold indenitely until a second
detection occurs.
4SETUP & OPERATION
When rst powered, the backlit hand symbol will alternate between blue and green for
approximately 5 seconds. Allow at least 15 seconds for the sensor to complete start up.
During normal operation, when a detection occurs, the hand symbol will momentarily change
from blue to green and the audible alert will sound (if enabled).