BEC Multi-Tenant Series 2017 Operating instructions

Installation Manual and
Programming Guide
Video Intercom System
Multi-Tenant/MT-Series
(2017)
BEC Integrated Solutions - Williamsville, New York - 716-689-0871

BEC Room Monitor - MT Series
Available in 5”, 7”, and 10”
in Black or White
Table of Contents
Getting Started
Thank you for choosing the BEC Video Intercom System! BEC is proud to introduce the
MT-Series - our recently updated 2-wire system, providing a straightforward installa-
tion, and a simple, yet intuitive user experience.
This manual includes installation steps, programming instructions, and wiring diagrams.
Please read all instructions in this manual carefully, and check all components before
installing them in the building. We recommend installing and testing one component at a
time (ie. room stations) making it easier to detect a potential error before completion.
Attached at the end of this installation section is a detachable End-User manual.
Feel free to detach the page, make copies, and distribute to your
tenants for their reference.
Set-Up/Installation
Wiring................................................2-3
Programming....................................4
RF Reader..............................................4
Electric Locks......................................5
Troubleshooting...............................5
Contact Us.....................................................7
Using Your Intercom
Calling.................................................6
Unlock.................................................6
Monitoring..........................................6
Ringtone.............................................6
Inner Calls.............................................7
Picture Memory...................................7
18-2 Wire Req’d
MT-801R
1
MT-812 MT-816EX

Set-Up/Installation
Wiring
MT-804R
MT-202 MT-PS
MT-7B MT-7B MT-7B
MT-2-4
Below is a sample four-monitor, single-entry wiring diagram using minimum 18-awg, unsheilded,
stranded wire. Please take careful note of the monitor bit-codes.
The diagram on the next page shows a 32-monitor conguration with an additional camera
(note: 32 monitors is the max no. of stations). Take note of the distance chart at the bottom of
the page to ensure your wire distances are under the listed limits.
To your next
MT-2-4...
120v AC
Wiring Distances
Chart on Next Page
SWI: DIP switches for system cong.
CN4: Call button expansion port
W1: Volume adjust
(L1, L2):To MT-202 (non-polaric)
CN5: External camera
SIP1: Door lock jumper
CN3: Electric lock port
2

If # of Room Stations < 20
Legend: distances
(1.) Door Station (MT-7xx/8xx) - DIP 1 + 2 should be set to 00
when there is only ONE door.
(2.) Power Supply (MT-PS) - Must be installed side-by-side with
the Power Separator.
(3.) Power Seperator (MT-202)
(4.) Monitor (MT-7B) - Each set with their unique 5 bit-code ()
(5.) Video Distributor (MT-2-4) - Set switch to OFF unless
at the end of the line.
(6.) Video Distributor (MT-2-4) - Switch set to ON at the end
(7.) Extra Camera
If # of Room Stations > 20
MT-202
MT-PS
MT-2-4
MT-2-4
3

Programming
User codes (Monitor Bit codes)- Every room station
must have an ID, set through the bit codes (listed right).
Bits 1-5 are used to congure the room ID;
Bit-6 is the line-terminal switch, at the
LAST monitor to ON, otherwise set OFF.
Bit-7 is to turn the ringtone at the door station
On/Off.
You can have a max of 3 monitors per button/code.
externaL caMera - Connect with CN5 at the outdoor
panel, at a room monitor, press and hold Alarm until it
beeps, then press Monitor twice. Press Alarm to save
and exit.
To DISABLE an extra camera, press and hold
Alarm until it beeps, press Monitor once. Press Alarm
to save and exit.
Mt-2-4 - The switch on the LAST distributor in your
chain must be set to ON.
rooM-to-rooM caLLing - Intra-calling is available to
place a voice call with one other connected monitor.
To enable, you must rst set the 2-digit dial number
of the monitor to call. Press and hold Unlock until you
hear a long beep, press Monitor 1-9 times to assign that
number, press Unlock to conrm.
Example - Monitor 4 wishes to call monitor 9:
[@ Monitor 4, set dial # to 09] HOLD Unlock (Beep) -
Unlock x1 (assigns 0) - Monitor x 9 (assigns 9) - Unlock
(enter/conrm)
RF Reader
To program your fobs, swipe the master card included with your system, swipe the cards you wish
to activate, then re-swipe your master card to complete. We recommended taking inventory of all
key-fob ID #’s before programming, in case they’re lost or stolen. You can de-program individual
fobs using the available remote accessory. (Model: BE-RKC)
4

Troubleshooting & FAQ’s
Electric Lock
Points to Consider
• We strongly recommend to use stranded, unshielded wire, 16-18 awg, 2-conductor.
• All connection points are non-polaric (+/-) with the exception of connecting the MT-202 to the Power
Supply.
• Please ensure your cable lengths do not exceed the distance ratings listed in the chart on page 3 of
this manual.
• The system power supply has a rating of 24v DC and should be within a +/- 2.0v range.
Tips/FAQ’s
• Set the dip switches to the same cong to have more than one monitor ring at once (max: 3 monitors)
• Use the YELLOW and RED wires for a standard, powered-to-open lock. Polarity will not matter at the
lock.
The MT series has a built in timer and power for a 12v
DC strike (max current = 250mA),
Set the jumper SIP1 set to 1-2 for a normally closed
lock (power OFF to open), or set SIP1 to 2-3 for a nor-
mally open lock (power ON to open).
Adjust the timer setting with Bit-4 and Bit-5 at the
outdoor station (00 = Off/Off):
NOTE: If you choose to use a lock that is anything
other than a 12v DC strike, you must remove the
jumper and use an external power source to supply
power to your lock. See the following diagram...
00 - 1 sec.
01 - 5 sec.
10 - 10 sec.
11 - 15 sec.
5

Special Case: MT-706
When setting up the MT-706, six-button outdoor panel, you must program the
monitors to these dip-settings in order to program the six buttons/monitors
correctly - the chart on pg. 4 is not applicable. This is the only door panel that
requires special conguration. See the following diagram...
5225 Sheridan Drive
Georgetown Square
Williamsville, NY 14221
Phone: [phone]
Toll-Free: 1-888-556-3998
E-Mail: [email protected]
http://www.becintegrated.com
MT-706 Button/Monitor Conguration
6
Version 1.3 - Revised 7/10/17
If you have questions on installation or if you run into any unforseen circumstances
while installing, please call our tech-support line at 716-689-0871 ext. 4
or toll-free at 888-556-3998.

7
5225 Sheridan Drive
Georgetown Square
Williamsville, NY 14221
Phone: [phone]
Toll-Free: 1-888-556-3998
E-Mail: [email protected]
http://www.becintegrated.com

Congratulations on your new Video Intercom System! At BEC we are proud
to provide secure, reliable entry solutions for your home or business. This
user manual will provide answers for any operational questions you may
encounter throughout your system’s lifetime.
The outdoor panel for your system has been installed and programmed to
ring your unit when the corresponding button is pressed.
If your panel is equipped with an RF Card Reader, swipe the card/key-fob
across the reader and the door will unlock.
The indoor room station has four illuminated buttons on the face and three
scrolling adjusters on the edge to control Brightness, Color, and
Volume.
The blue illuminated buttons from left to right are Monitor, Alarm, Unlock,
and Talk/Listen.
To answer an incoming call, press Talk to answer, then speak freely. Calls
last for 90 seconds - you DO NOT have to hold talk to enable voice
communication. Press talk again to end the conversation.
To Unlock the door, press the unlock button during a call and the door
should release to allow entry.
Press Monitor button while in standby mode and you will be able to view
the outdoor station camera. If there is an additional surveillance
camera, press Monitor button again to switch modes. Press
Talk twice to exit.
To change the Ringtone, press and hold Talk until you hear your current
ringtone, then press Alarm to cycle throught the different tones,
then press Talk to save.
BEC Room Monitor - MT Series
Available in 5”, 7”, and 10”
in Black or White
MT-801R MT-812
Programmable
Entry Key-Fobs
Available
8
Video Intercom Systems (MT-Series)
User Guide and System Instructions
Getting Started
Door Entry
Video Monitor Functions

5225 Sheridan Drive
Georgetown Square
Williamsville, NY 14221
Phone: [phone]
Toll-Free: 1-888-556-3998
E-Mail: [email protected]
http://www.becintegrated.com
If your system is equipped with the optional
Picture Memory function, you will notice the
additional feature controls on the side of the
monitor.
1. Setting Time - Press Monitor, press Menu
twice to choose the date, then adjust the year
by pressing Up or Down. Press Menu to move
on to Month, Day, and then Time. Scroll down to
EXIT and press Save/Back to complete.
2. Viewing Pictures - Press Monitor, then
press Up or Down to view the saved photos.
3. Deleting Pictures - Press Monitor, press Up or Down to view
the saved photos, press Menu to choose a photo, and press Menu
again to delete.
4. Delete All Pictures - Press Monitor, press menu to scroll to
“Delete All”, Press Up to choose Yes/No, and conrm by pressing
Menu again.
5. Manually Photograph - Press Monitor button, and press Photo-
graph to save a picture. Max no. of saved photos is ~240.
If you have questions or if you run into any issues while
using your system, please call our tech-support line at
716-689-0871 ext. 4 or toll-free at 888-556-3998.
9
Picture Memory