BEC M2M MX-200e User manual

Quick Install Guide
1
2
Attach the Antennas
Screw the male antennas until
fully attached to SMA female
connectors of the Cellular
and/or GPS Modules.
Connect to the MAIN port, the
primary cellular antenna port to
transmit and receive signal, if
decide to use one LTE antenna.
Do not over-torque the antenna
on the connector.
LAN - Green: Connected to a Gigabit (1000Mbps) device.
Orange: Connected to a 10/100Mbps device
Blinking: Data being transmitted / received
LTE Signal Strength –Green: RSSI > -69dBm. Excellent
Green / Fast Flashing: -69 > RSSI > -81dBm. Good.
Red / Fast Flashing: -81 > RSSI > -99dBm. Fair.
Red / Slow Flashing: -99dBm > RSSI. Poor
Red: No Cellular signal. Cellular module still in service
Off: No Cellular module or module failure
Internet - Green: IP traffic via WAN
Red: WAN IP request failed
Off: No WAN connection or in Bridge mode
Power - Green: System ready. Red: Boot failure
WHAT’S IN THE BOX
1 x BEC MX-200e WWAN Failover Manager
1 x This Quick Install Guide
1 x CD containing the User Manual
1 x DIN Rail Mounting Kit
1 x Power Terminal Block 2-Pin 3.5mm
1 x Power Converter with 2-Pin Terminal Block
1 x DC Power Adapter, 12V 1.2A
(Optional Accessories)
3G/4G Antennas
Active GPS Antenna
Ethernet (RJ-45) Cable
SETTING UP THE ROUTER
DEVICE OVERVIEW & LEDS
Insert the SIM card
Slide the SIM card (2FF)
with the mental contacts
(gold plate) facing down to
the SIM slot then push it
all the way in until you
hear the clicking sound.
Connect the Serial (RS-232)
Use a RS-232 (DB-9)
male serial adapter to
connect with industrial
equipment –including
PLC, SCADA, Sensor,
Meters, and Motor.
3
4
5
Access to the MX-200e Web Graphic Interface (GUI) by entering
http://192.168.1.254 in the address bar of the web browser.
Default Login Information: Username / Password (admin /admin).
The Quick Start Wizard provides key steps to connect the MX-200e
to the Internet.
Connect to the MX-200e
1.1 Attach the power
converter with 2-pin
terminal block to the
MX-200e and plug in the
supplied power adapter
Connect to Power Source
1.2 Attach the power
terminal block (TB) to the
MX-200e and connect the wire
leads of the power supply
cable to the TB plug.
The red wire (Power/VCC -
the left connector) should
connect to the positive
terminal.
The black wire to the ground
(GND - the right connector) of
the power supply. Input
voltage range is from 9-56V.
1
2
3
4

ATTACHING TO A DIN RAIL REMOVING FROM A DIN RAIL
MOUNTING POSITIONS
Remove MX-200e from a DIN rail.
1-2. Push down the MX-200e to free the bottom of the
clip from the DIN rail.
3. Unhook the top of the clip and pull the MX-200e
away from the DIN rail
DIN RAIL MOUNTING
DIN RAIL MOUNTING OPTIONS
KIT CONTAINS: DIN Rail Clip and Six (6) Clip Mounting Screws
The DIN Rail mounting kit is designed to securely attach and clip the MX-200e onto a TS35 or standard 35mm top hat (EN
500022/BS 5584) DIN rail in the horizontal position.
Two (2) mounting locations to mount the DIN rail clip on the surface of MX-200e, back or rear side.
Please follow the steps to complete DIN rail mounting installation.
Clip and secure the MX-200e onto a DIN rail.
1. Hook the top of the clip onto the top edge of the DIN
rail. Make sure the clip is firmly against the rail.
2. Push down the bottom of the MX-200e to snap it
onto the lower edge of the DIN rail.
3. The MX-200e is now mounted on the DIN rail.
Attach and fasten the DIN rail clip (known as clip)
to the back or rear side of the MX-200e using two (2) clip
mounting screws included in this mounting kit.
1.MX-200e 2.DIN rail clip 3.Mounting Screws
I
II
Install clip in either vertical or horizontal position
I
I
SUPPORT: Visit us at www.bectechnologies.net.