Becker CentralControl CC41 User manual

CC41
Stand 07/2021

First steps
Short instruction

3
Aufbau und AnschlüsseFirst steps
•Plug in the mains cable and wait approx. 5 s
•The red LED on the front flashes red and
blue alternately several times (change of
network configuration)
•After that, the blue LED lights up continuously
and the red LED flashes cyclically, indicating
that the access point is activated - the unit is
now in setup mode

4
Aufbau und AnschlüsseFirst steps
•Install the Becker CentralControl app
(iOS/Android) using the following QR code
•(also included in the operating instructions),
or enter "Becker CentralControl" in the
search field of the AppStore or PlayStore.
•Start the app

5
Aufbau und AnschlüsseFirst steps
•Select the CentralControl CC41

6
Aufbau und AnschlüsseFirst steps
•You will be advised that the CC41 must be
in set-up mode
•If the CentralControl is already in your
network, for example when connected with
a cable, it will appear under
"CentralControls in your network".
• Press „Continue“

7
Aufbau und AnschlüsseFirst steps
•Allow your mobile phone to connect to the
Access Point of the CC41 and press
"Connect".
•If you are asked for location permissions,
please allow them - the app needs them to
find your CentralControl in the network later.

8
Aufbau und AnschlüsseFirst steps
•Select your WLAN from the list of networks
foundTragen Sie den Netzwerkschlüssel ein
•Tap on „Connect“
•Attention! Please do not use guest networks
to operate your CentralControl. These
usually prohibit communication between
your smartphone and other network
participants such as the CentralControl.

9
Aufbau und AnschlüsseFirst steps
•The CC41 now connects to your home
network
•The LED in the CC41 lights up blue to
indicate that the connection was successful.
•Make sure that your smartphone and the
CentralControl are then in the same
network.

10
Aufbau und AnschlüsseFirst steps
•If the connection was successful, your
CentralControl will now be found
automatically
•Now tap on the upper menu item or
alternatively set up remote access directly
via the Becker Gateway server
•Done! You can now control your
CentralControl with your smartphone

11
Aufbau und AnschlüsseReset / Activate Access Point
•If the connection fails and the LED on the
front of your CentralControl lights
permanently red, an error has probably
occurred when entering the network data.
•In that case put the CentralControl back into
teach-in mode
•To do this, press the reset button (in the
centre of the bottom of the AV socket) until
the LED confirms the process by flashing
red and blue.

Rooms, receivers and timers

13
Aufbau und AnschlüsseAdd rooms
•Swipe left and right to navigate through the
app's menu items
•Alternatively, the current menu item can
also be dragged downwards to show a
quick navigation
•Select the item "Rooms"

14
Aufbau und AnschlüsseAdd rooms
•Tap the "+" symbol to create a new room
•By tapping the cogwheel symbol in the
upper right corner, rooms can be deleted or
created later.

15
Aufbau und AnschlüsseAdd rooms
•Enter the name of the new room and tap on
"Add room".

16
Aufbau und AnschlüsseAdd rooms
•With this you can create all the rooms for
your house
•By moving the icons, you can change the
arrangement of your rooms as you desire
•Open the room you want to place the
receivers in(tubular drives, external radio
receivers, etc.) by tapping on it.

17
Aufbau und AnschlüsseAdd receivers
•For better recognition, you can optionally
assign an image to the room (your own
photo or standard image).
•To teach in a receiver, tap on "+".

18
Aufbau und AnschlüsseAdd receivers
•Select the corresponding radio system and
follow the instructions in the app and the
operating instructions of the device to be
taught in
Für das Herstellen der Lernbereitschaft an
den Empfängern beachten Sie bitte:
Centronic: Via master handheld transmitter
B-Tronic: Via a taught-in transmitter or by
switching on the power supply
CentronicPLUS: By switching on the power
supply of a unit in the installation

19
Aufbau und AnschlüsseAdd receivers
•In our example, we use the CentronicPLUS
radio system. Here, after a short time, all the
devices that have previously been put into
teach-in readiness are automatically listed
•Select the desired receiver (the selected
CentronicPLUS receiver clicks or waves for
identification)
•After the selection, tap on "Teach in".

20
Aufbau und AnschlüsseAdd receivers
•Name the receiver according to your wishes
•For better recognition, you can optionally
assign a picture to the recipient (your own
photo or standard picture).