Beckhoff CU8880-0010 User manual

Installation- and Operating instructions for
CU8880-0010
Ethernet Controller with USB Input
Version: 1.4
Date: 2018-04-12

Table of contents
Table of contents
1.
2.
3.
4.
5.
General instructions 2
Notes on the Documentation 2
Liability Conditions 2
Trademarks 2
Patent Pending 2
Copyright 2
State at Delivery 2
Delivery conditions 2
Description of safety symbols 3
Product Description 4
Product Overview 4
Power Supply 5
Data connectors 5
USB type B Port (X20) (standard-cable) 5
RJ 45-Port (X10) (standard CAT5-cable) 5
LED Diagnostics 6
Installation Instructions 7
Transport and Unpacking 7
Transport 7
Unpacking 7
Mounting / Unmounting 8
Connecting devices 9
Connecting cables 9
Operating Instructions 10
Configuration 10
Appendix 11
Assembly dimensions 11
Service and Support 12
Beckhoff's branch offices and representatives 12
Beckhoff headquarters 12
Beckhoff Support 12
Beckhoff Service 12
Technical data 13
Approvals for USA and Canada 13
FCC: Federal Communications Commission Radio Frequency Interference
Statement 13
FCC: Canadian Notice 13
CU8880-0010 1

General instructions
General instructions
Notes on the Documentation
This description is only intended for the use of trained specialists in control
and automation engineering who are familiar with the applicable national
standards. It is essential that the following notes and explanations are
followed when installing and commissioning these components.
The responsible staff must ensure that the application or use of the
products described satisfy all the requirements for safety, including all the
relevant laws, regulations, guidelines and standards.
Liability Conditions
The documentation has been prepared with care. The products described
are, however, constantly under development. For that reason the
documentation is not in every case checked for consistency with
performance data, standards or other characteristics. In the event that it
contains technical or editorial errors, we retain the right to make alterations
at any time and without warning. No claims for the modification of products
that have already been supplied may be made on the basis of the data,
diagrams and descriptions in this documentation.
All pictures shown in the documentation are exemplary. Illustrated
configurations can differ from standard.
Trademarks
Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®
and XFC®are registered trademarks of and licensed by Beckhoff
Automation GmbH.
Other designations used in this publication may be trademarks whose use
by third parties for their own purposes could violate the rights of the
owners.
Patent Pending
The EtherCAT Technology is covered, including but not limited to the
following patent applications and patents:
EP1590927, EP1789857, DE102004044764, DE102007017835
with corresponding applications or registrations in various other countries.
The TwinCAT Technology is covered, including but not limited to the
following patent applications and patents:
EP0851348, US6167425 with corresponding applications or registrations in
various other countries.
Copyright
© Beckhoff Automation GmbH & Co.KG.
The reproduction, distribution and utilization of this document as well as the
communication of its contents to others without express authorization are
prohibited. Offenders will be held liable for the payment of damages. All
rights reserved in the event of the grant of a patent, utility model or design.
State at Delivery
All the components are supplied in particular hardware and software
configurations appropriate for the application. Modifications to hardware or
software configurations other than those described in the documentation
are not permitted, and nullify the liability of Beckhoff Automation
GmbH & Co.KG.
Delivery conditions
In addition, the general delivery conditions of the company Beckhoff
Automation GmbH & Co.KG apply.
2CU8880-0010

General instructions
Description of safety symbols
The following safety symbols are used in this operating manual. They are
intended to alert the reader to the associated safety instructions.
Danger This symbol is intended to highlight risks for the life or health of personnel.
Warning
This symbol is intended to highlight risks for equipment, materials or the
environment.
i
Note This symbol indicates information that contributes to better understanding.
CU8880-0010 3

Product Description
Product Description
Product Overview
View of the CU8880-0010
The CU8880-0010 USB-to-LAN adapter places an additional industrially-
suited and independent Ethernet interface at the user’s disposal. In this
way, four or more Ethernet interfaces can be implemented, depending on
the system configuration. The CU8880-0010 is used for necessary IT
communication, so that the respective on-board Ethernet interfaces are
available for EtherCAT or real-time Ethernet communication.
• user-friendly installation via integrated top hat rail adapter
• power supply via USB - no supply voltage necessary
• compact industrial design
• clear quick diagnosis by separate LEDs.
4CU8880-0010

Product Description
Power Supply
Power supply via USB-port The Ethernet controller does not need any
additional power supply. The power supply
(5 V DC) is realized by the USB connector.
The LED P20 lights green when power supply
is connected.
Data connectors
The connector are 1 USB port Type B and a RJ45-connector. The pins
are described below:
USB type B Port (X20) (standard-cable)
USB type B Port
Pin Signal
1 VCC
2 Data -
3 Data +
4 GND
shield shield
RJ 45-Port (X10) (standard CAT5-cable)
RJ 45 Port
Pin Signal
1 TX+
2 TX-
3 RX+
4 n.c.
5 n.c.
6 RX-
7 n.c.
8 n.c.
CU8880-0010 5

Product Description
LED Diagnostics
LED Diagnostics
The following table shows the possible states for the LEDs:
LED Assignment Status Meaning
off no power supply connectedP20 power supply
lights green 5 VDC via USB-Port
offP10 Ethernet port
lights green Ethernet Collision
offP11 Ethernet port
lights yellow Ethernet full duplex
offP12 Ethernet port
lights Ethernet Link
off Ethernet Speed 10MBitP13 Ethernet port
lights Ethernet Speed 100MBit
6CU8880-0010

Installation Instructions
Installation Instructions
Please also refer to chapter General instructions.
Transport and Unpacking
The specified storage conditions must be observed (see chapter Technical
data).
Transport
Despite the robust design of the unit, the components are sensitive to
strong vibrations and impacts. During transport, the unit should therefore
be protected from excessive mechanical stress. Therefore, please use the
original packaging.
Warning
Danger of damage to the unit!
If the device is transported in cold weather or is exposed to extreme
variations in temperature, make sure that moisture (condensation) does not
form on or inside the device.
Prior to operation, the unit must be allowed to slowly adjust to room
temperature. Should condensation occur, a delay time of approximately 12
hours must be allowed before the unit is switched on.
Unpacking
Proceed as follows to unpack the unit:
1.Remove packaging.
2.Do not discard the original packaging. Keep it for future relocation.
3.Check the delivery for completeness by comparing it with your order.
4.Please keep the associated paperwork. It contains important
information for handling the unit.
5.Check the contents for visible shipping damage.
6.If you notice any shipping damage or inconsistencies between the
contents and your order, you should notify Beckhoff Service.
CU8880-0010 7

Installation Instructions
Mounting / Unmounting
The CU8880-0010 can be snapped onto a 35 mm mounting rail conforms
to EN 50022.
Mounting the Ethernet
Controller
Just push the unit on the upper side under the rail (figure 1) and snap in
the lower side as shown below (figure 2):
Unmounting the Ethernet
Controller
To release the CU8880-0010 from the mounting rail pull down the locking
clip with a screwdriver (figure 1) and pull off the device from the rail
(figure 2):
8CU8880-0010

Installation Instructions
Connecting devices
Warning
The power supply plug must be withdrawn!
Please read the documentation for the external devices prior to connecting
them.
During thunderstorms, plug connector must neither be inserted nor
removed.
When disconnecting a plug connector, always handle it at the plug. Do not
pull the cable!
Connecting cables
The connections are documented in the section Product Description.
When connecting the cables to the CU8880-0010, proceed according to
the following sequence:
• Switch off all the devices that are to be connected.
• Disconnect all the devices that are to be connected from the power
supply.
• Connect all the cables between the CU8880-0010 and to the
devices that are to be connected.
• Reconnect all devices to the power supply.
CU8880-0010 9

Operating Instructions
Operating Instructions
Configuration
i
Note
The provided CD contains the according configuration software.
10 CU8880-0010

Appendix
Appendix
Assembly dimensions
The product is characterized by small overall installed size. With a height of
approx. 100 mm, the module dimensions exactly match those of the
Beckhoff Bus Terminals. Together with the lowered connector surfaces,
this means that it can be used in a standard terminal box with a height of
120 mm.
CU8880-0010 11

Appendix
Service and Support
Beckhoff and their partners around the world offer comprehensive service
and support, making available fast and competent assistance with all
questions related to Beckhoff products and system solutions.
Beckhoff's branch offices and representatives
Please contact your Beckhoff branch office or representative for local
support and service on Beckhoff products!
The addresses of Beckhoff's branch offices and representatives round the
world can be found on her internet pages:
http://www.beckhoff.com
You will also find further documentation for Beckhoff components there.
Beckhoff headquarters
Beckhoff Automation GmbH & Co. KG
Huelshorstweg 20
D-33415 Verl
Germany
Phone: [phone]
Fax: [phone]
e-mail: [email protected]
Beckhoff Support
Support offers you comprehensive technical assistance, helping you no
only with the application of individual Beckhoff products, but also with
other, wide-ranging services:
• world-wide support
• design, programming and commissioning of complex automation
systems
• and extensive training program for Beckhoff system components
Hotline: [phone]
Fax: [phone]
e-mail: [email protected]
Beckhoff Service
The Beckhoff Service Center supports you in all matters of after-sales
service:
• on-site service
• repair service
• spare parts service
• hotline service
Hotline: [phone]
Fax: [phone]
e-mail: [email protected]
Quote the project number If servicing is required, please quote the project number of your Industrial
PC.
12 CU8880-0010

Appendix
CU8880-0010 13
Technical data
Number of ports 1 USB-input type B
1 Ethernet interface with 10/100BASE-T-connector RJ45
Supported USB standard USB 2.0
Status display 5 LEDs
USB wiring length maximum 1 meter
Power supply power supply via USB input connector
Max. current input from 5 V
USB
maximum 500 mA at 5V DC
The following conditions must be observed during operation:
Environmental conditions Ambient temperature: 0 to 55°C (operation)
-25°C to +70°C (transport/ storage)
Atmospheric humidity: Maximum 95%, non-condensing
Vibration/ Shock resistance EN 60068-2-6 / EN 60068-2-27
EMC resistance burst/ ESD EN 60000-6-2 / EN 60000-6-4
Protection class IP20
Do not use the CU8880-
0010 in areas of explosive
hazard
The Ethernet Controller may not be used in areas of explosive hazard.
Dimensions (W x H x D) app. 35 mm x 98,5 mm x 76,6 mm (with mounting for DIN rail)
Weight app. 95 g
Assembly on 35 mm mounting rail conforms to EN 50022
Installation position any
Approvals CE
Approvals for USA and Canada
FCC: Federal Communications Commission
Radio Frequency Interference Statement
FCC Approval for USA This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
FCC: Canadian Notice
FCC Approval for Canada This equipment does not exceed the Class A limits for radiated emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications.