BedJet 1222NA Operation instructions

IMPORTANT INSTRUCTIONS
USER OPERATING MANUAL – MODEL 1222NA/2222EU
Revision 1.0 P a g e | 1
VET Forced Air Animal Warmer
with Remote Control
This device is designed for animal and pet warming use only. It is not
for use in any human household or human medical application.
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE,
INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
®

IMPORTANT INSTRUCTIONS
USER OPERATING MANUAL – MODEL 1222NA/2222EU
Revision 1.0 P a g e | 2
IMPORTANT INSTRUCTIONS
DANGER: TO REDUCE RISKS OF BURNS, ELECTRIC SHOCK, FIRE AND PERSONAL INJURY, THIS
PRODUCT MUST BE USED IN ACCORDANCE WITH THE FOLLOWING INSTRUCTIONS
1. Read all instructions before using this device. Use this device only as described in this
manual. Any other use not recommended by the manufacturer may cause fire, electrical
shock, or injury to persons.
2. Do not operate device unattended. Turn off or unplug when not in use.
3. Make certain that the power source conforms to the electrical requirements of this device.
4. DO NOT OPERATE MORE THAN ONE BEDJET ON SAME AC-POWER OUTLET WITHOUT
ADJUSTING DUAL MODE SWITCH LOCATED ON REAR OF DEVICE TO “DUAL ZONE ON, LOW
POWER” FOR REDUCED POWER
5. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety feature.
6. DO NOT plug device into any other cord connected device, such as a power strip, surge
protector, multiple outlet adapters or outlet-type air fresheners. The use of such devices
may create a fire hazard. Plug unit directly into a wall outlet only.
7. Always plug this device directly into a wall outlet/receptacle. Never use with an extension
cord or relocatable power tap (outlet/power strip).
8. Do not operate this device with a damaged cord or plug or after the device malfunctions or
has been dropped or damaged in any manner. Return device to authorized service facility
for examination, electrical or mechanical adjustment or repair.
9. To disconnect device, make sure device is not currently operating in heat or cool mode, turn
Power Switch to OFF, then remove plug from outlet.
WARNING
ANIMAL USE ONLY - DO NOT USE THIS WARMING SYSTEM FOR ANY
HUMAN APPLICATION
DO NOT USE FOR ANY HUMAN MEDICAL, OXYGEN OR WET
ENVIRONMENT

IMPORTANT INSTRUCTIONS
USER OPERATING MANUAL – MODEL 1222NA/2222EU
Revision 1.0 P a g e | 3
10. Always unplug device when not in regular use. Unplug power cord before servicing or
moving the device. WARNING: DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE
MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE DEVICE. ALWAYS
UNPLUG THE POWER CORD.
11. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening
as it may cause an electric shock, fire, or damage the device. Do not block or tamper with
the device in any manner while it is in operation.
12. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place
unit on soft surfaces, like a bed, where openings may become blocked.
13. Always place the device on a stable, flat, level surface when operating, to avoid the chance
of the device overturning. Locate the power cord so the device or other objects are not
resting on it. Do not run cord under carpeting. Do not route cord under furniture or
appliances. Arrange cord away from traffic area and where it will not be tripped over.
14. This device has hot and arcing or sparking parts inside. Do not use the BedJet in areas where
gasoline, paint, or flammable liquids or flammable gases are used or stored. It must NOT be
used in potentially dangerous locations such as flammable, explosive, chemical -laden or wet
atmospheres.
15. This device is not intended for use in wet or damp locations. This device is NOT INTENDED
for use in bathrooms, laundry areas and similar indoor locations. Never locate the device
where it may fall into a bathtub or other water container. Do not immerse BedJet in water
16. This device is not intended for use as a room air heater.
17. Do not use device outdoors.
18. Keep the cord away from heated surfaces.
19. Do not operate where aerosol (spray) products are being used or in oxygen rich
environments.
20. Check your BedJet cord and plug connections:
a) Faulty wall outlet connections or loose plugs can cause the outlet or plug to overheat.
Be sure the plug fits tight in the outlet.
b) Heaters draw more current than small appliances, overheating of the outlet may occur
even if it has not occurred with the use of other appliances.
c) During use check frequently to determine if your plug outlet or faceplate is HOT!
d) If so, discontinue use of the heater and have a qualified electrician check and/or replace
the faulty outlets.

IMPORTANT INSTRUCTIONS
USER OPERATING MANUAL – MODEL 1222NA/2222EU
Revision 1.0 P a g e | 4
21. CAUTION — Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
22. Heater must not be located immediately below a socket outlet.
23. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS DEVICE WITH
ANY SOLID STATE SPEED CONTROL DEVICES.
SAVE THESE SAFETY INSTRUCTIONS
MANUFACTURER INFORMATION:
BEDJET LLC
217 Goddard Row
Newport, RI 02840 USA
Phone: [phone]
Email: [e-mail]

IMPORTANT INSTRUCTIONS
USER OPERATING MANUAL – MODEL 1222NA/2222EU
Revision 1.0 P a g e | 5
Pre-Installation Checklist
Before attempting installation of the BedJet, please verify the following parts list from your
boxed BedJet package:
Proper Assembly Required:
All parts included are required to be fully assembled and installed onto the BedJet as part any
operation. Do not operate the BedJet without the included Air Hose. Do not attempt to use
the BedJet with air delivery accessories or air delivery components not approved or supplied by
BEDJET LLC.
Air Hose with fabric liner,
stretchable, compressible
and bendable
BedJet VET and pre-installed
HEPA filter
Radio wireless remote control
with A23 alkaline battery
1)