BEDU SPA 11 Series User manual

*Self-draining whirlpool pumps
OPERATING INSTRUCTIONS
SPA

SPA Rev7.indd 1 08/02/19 17:46

GB
Page 8 / 28 SPA Rev7 - Operating Instructions
THIS INSTRUCTION MANUAL IS THE PROPERTY
OF BEDU POMPEN ANY REPRODUCTION, EVEN
IF PARTIAL, IS FORBIDDEN
1. GENERAL INFORMATION
Before using the product carefully read the information
contained in this instruction manual, the manual should
be kept for future reference.
Italian is the original language of this instruction
manual, this language is the reference language in
case of discrepancies in the translations.
This manual is part of the essential safety requirement
and must be retained until the product is nally de-
commissioned.
The customer, in case of loss, can request a copy
of the manual by contacting Bedu Pompen BV or their
agent, specifying the type of product data shown on
the label of the machine (see 2.3 Marking)
Any changes, alterations or modications made to the
product or part of it, not authorized by the manufacturer,
will revoke the “CE declaration” and warranty.
This appliance should not be operated
by children younger than 8 years,
people with reduced physical, sensory
or mental capacities, or inexperienced
people who are not familiar with the
product, unless they are given close
supervision or instructions on how to
use it safely and are made aware by
a responsible person of the dangers
its use might entail. Children must not
play with the appliance.
It is the user's responsibility to clean
and maintain the appliance. Children
should never clean or maintain it
unless they are given supervision.
Read carefully the installation
section which sets forth:
-
Themaximum permissiblestructural
working pressure (chapter 3.1).
- The type and section of the
power cable (chapter 6.5).
- The type of electrical protection
to be installed (chapter 6.5).
1.1. Symbols
To improve the understanding of the manual, below are
indicated the symbols used with the related meaning.
Information and warnings that must be
observed, otherwise there is a risk that the
machine could damage or compromise
personnel safety.
The failure to observe electrical information
and warnings, could damage the machine or
compromise personnel safety.
i
Notes and warnings for the correct management
of the machine and its parts.
Operations that could be performed by the nal
user. After carefully reading of the instructions,
is responsible for maintenance under normal
conditions. They are authorized to affect
standard maintenance operations.
Operations that must be performed by a
qualied electrician. Specialized technician
authorised to affect all electrical operations
including maintenance. They are able to
operate with in the presence of high voltages.
Operations that must be done performed by
a qualied technician. Specialized technician
able to install the device, under normal
conditions, working during “maintenance”,
and allowed to do electrical and mechanical
interventions for maintenance. They must
be capable of executing simple electrical
and mechanical operations related to the
maintenance of the device.
Indicates that it is mandatory to use individual
protection devices.
OFF
Operations that must be done with the device
switched off and disconnected from the power
supply.
ON
Operations that must be done with the device
switched on.
1.2. Manufacturer name and address
M
A
3
w
1.3. Authorized operators
The product is intended for use by expert operators
divided into end users and specialized technicians.
(see the symbols above).
i
It’s forbidden, for the end user, carry out
operations which must be done only by
specialized technicians. The manufacturer
declines any liability for damage related to the
non-compliance of this warning.
1.4. Warranty
For the product warranty refer to the general terms and
conditions of sale.
SUMMARY
1. GENERAL INFORMATION.............................8
2. TECHNICAL DESCRIPTION.......................... 9
3. TECHNICAL FEATURES................................9
4. SAFETY..........................................................9
5. TRANSPORTATION AND HANDLING ......... 10
6. INSTALLATION.............................................10
7. STARTUP AND OPERATION ....................... 11
8. MAINTENANCE............................................ 11
9. DISPOSAL....................................................12
10. SPARE PARTS .............................................12
11. ESIGNATION OF PARTS .............................12
12. TROUBLESHOOTING..................................13
Drawing for dismantling and assembly..................26
Declaration of conformity.......................................28
SPA Rev7.indd 8 08/02/19 17:46
Bedu Pompen B.V.
Poort van Midden Gelderland Rood 10
6666 LT HETEREN, The Netherlands

GB
i
The warranty covers only the replacement and
the repair of the defective parts of the goods
(recognized by the manufacturer).
The Warranty will not be considered in the following
cases:
- Whenever the use of the device does not conform
to the instructions and information described in this
manual.
- In case of changes or variations made without
authorization of the manufacturer.
- In case of technical interventions executed by a non-
authorized personnel.
- In case of failing to carry out adequate maintenance.
1.5. Technical assistance
Any further information about the documentation,
technical assistance and spare parts, shall be
requested from: Bedu Pompen B.V. (paragraph 1.2).
2. TECHNICAL DESCRIPTION
Self-draining, single-impeller pumps, with motor
insulated from pumped water, constructed with high
quality, corrosion-proof plastic materials, with stainless
steel diffuser.
PVC pipe connections:
Ports for cementing joint, with external thread for union
coupling.
2.1. Intended use
For water circulation in spas, hydromassage bathtubs
and whirlpools.
For clean water with a maximum temperature of 60 °C
(140 °F).
Limit the water at the inlet to the bathtub to a
maximum temperature of 50 °C (122 °F).
Maximum water level in the bathtub or spa: 2,000 mm
above the pump.
2.2. Improper use
The device is designed and built only for the purpose
described in paragraph 2.1.
Improper use of the device is forbidden, as is
use under conditions other than those indicated
in these instructions.
Improper use of the product reduces the safety and
the efciency of the device, Bedu shall not be
responsible for failure or accident due to improper use.
Do not use in ponds, tanks or swimming pools
or where people may enter or come into contact
with the water.
2.3. Marking
The following picture is a copy of the name-plate that is
on the external case of the pump.
Example plate pump
Montorso (VI) Italy IT 00142630243
Made in Italy
3. TECHNICAL FEATURES
3.1. Technical data
Dimensions and weight (see technical catalogue).
Nominal speed 2900/3450 rpm
Protection IP X5
Supply voltage / Frequency:
- up to 240V 1~ 50/60 Hz
- up to 480V 3~ 50/60 Hz
Check that the mains frequency and voltage
correspond to the electrical characteristics shown on
the indicator plate.
The electric data marked on the label are referred to
the nominal power of the motor.
Sound pressure: < 70 dB (A).
Max. starts per hour: 30 at regular intervals.
Maximum permissible pressure in the pump casing: 25
m (2,5 bar).
Maximum suction pressure: PN (Pa) - Hmax (Pa).
3.2. Operating conditions
Installation in well ventilated location protected from
the weather, with a maximum ambient temperature of
40 °C.
4. SAFETY
4.1. General provisions
Before using the product it is necessary to
know all the safety indications.
Carefully read all operating instructions and the
indications dened for the different steps: from
transportation to disposal.
The specialized technicians must carefully comply
with all applicable standards and laws, including local
regulations of the country where the pump is sold.
The device has been built in conformity with the current
safety laws. The improper use could damage people,
animals and objects.
The manufacturer declines any liability in the event of
damage due to improper use or use under conditions
other than those indicated on the name-plate and in
these instructions.
i
Follow the routine maintenance schedules and
the promptly replace damaged parts, this will
allows the device to work in the best conditions.
Use only original spare parts provided from Bedu
pompen BV or from an authorized distributor.
Don’t remove or change the labels placed on
the device.
Do not start the device in case of defects or damaged
parts. Maintenance operations, requiring full or partial
disassembly of the device, must be done only
after disconnection from the supply.
4.2. Safety devices
The device has an external case that prevents any
contact with internal parts.
4.3. Residual risks
The appliance, designed for use, when used in-line with
the design and safety rules, doesn’t have residual risks.
4.4. Information and Safety signals
For this kind of product there will not be any signals
on the product.
SPA Rev7.indd 9 08/02/19 17:46

GB
Page 10 / 28 SPA Rev7 - Operating Instructions
4.5. Individual protection devices
During installation, starting and maintenance it is
suggested to the authorized operators to consider
the use of individual protection devices suitable for
described activities.
During ordinary and extraordinary maintenance
interventions, safety gloves are required.
Signal individual protection device
HAND PROTECTION
(gloves for protection against chemical,
thermal and mechanical risks).
5. TRANSPORTATION AND HANDLING
The product is packed to maintain the content intact.
During transportation avoid to stack excessive weights.
Ensure that during the transportation the box cannot
move.
It is not necessary to use any special vehicle to
transport the packaged device.
The transport vehicles must comply, for the weight and
dimensions, with the chosen product (see technical
catalogue dimensions and weights).
5.1. Handling
Handle with care, the packages must not receive
impacts.
Avoid to impact onto the package materials that could
damage the pump.
6. INSTALLATION
6.1. Dimensions
For the dimensions of the device (see technical
catalogue).
6.2. Ambient requirements and installation site
dimensions
The customer has to prepare the installation site in
order to guarantee the right installation and in order to
fulll the device requirements (electrical supply, etc...).
The place where the device will be installed must fulll
the requirements in the paragraph 3.2.
It's Absolutely forbidden to install the machine in an
environment with potentially explosive atmosphere.
6.3. Unpacking
i
Inspect the device in order to check any
damages which may have occurred during
transportation.
Package material, once removed, must be discarded/
recycled according to local laws of the destination
country.
6.4. Installation
The SPA pumps must be installed with the rotor
axis horizontal and feet downwards in piping layouts
in which the lling and draining of the pump
is obtained through the pipes, with lling and
draining of the bathtub or spa.
Whirlpool tubs must be constructed so that the
water cannot remain in the system after the tub
has been drained.
To allow for self-draining, mount the pump on a base
positioned at a level equal to or higher than the bathtub
or spa suction port and, to allow for lling, with the
delivery port positioned at a level lower than that for
normal lling (under the overow discharge).
Installation beneath the skirt of a bathtub or spa
which is closed externally with protection panels must
provide at least one slot with a 5-10 mm aperture
(preferably between the panel and the oor) suitable
for air recirculation for ventilation of the motor.
Mount the pump on a base located at least 40 mm
(11/2 inches) above the intended mounting surface.
For outdoor spas or whirlpools, the pump and electric
parts must be installed within an enclosure for
protection from the weather and ooding and installed
on a base located at least 100 mm (4 inches) above
the mounting surface.
Make sure installation allows access for servicing and
inspection, disassembly or replacement of the pump.
Follow standards for safety (some safety standards
are indicated in the section 6.5.).
6.4.1. Pipes
Connections of pipes to the pump ports.
Use pipes made of PVC type, plastic material.
The pump ports are designed to allow for direct
cemented joints (g. 1). The external thread allows for
connection with an optional, removable union coupling
(g. 2).
3.93.033/1
3.93.033/2
Fig. 1 Cemented joint.
3.93.033/1
3.93.033/2
Fig. 2 Threaded union coupling.
To join the pipe to the pump or to the union coupling,
use an adhesive or cement suitable for the ABS
material. Follow carefully the instructions of the
product chosen .
Tighten union couplings to the extent sufcient to
ensure a tight seal.
Avoid tightening too much as excessive torque may
damage the pump or the union couplings themselves.
Make sure all joints are properly sealed.
The diameter of the pipes must not be smaller than the
diameter of the pump ports.
Place a removable lter inside the bathtub or whirlpool
suction port.
The suction pipe must have a minimum length of
500 mm and must lead upwards from the bathtub or
whirlpool suction port to the pump suction port.The
delivery pipe must also be positioned to allow for
complete draining when the bathtub is drained .
SPA Rev7.indd 10 08/02/19 17:46

GB
SPA Rev7 - Operating Instructions Page 11 / 28
6.5. Electrical connection
OFF
Electrical connection must be carried out only
by a qualied electrician in accordance with
local regulations.
Follow safety standards EN 60335-2-41, EN 60335-
2-60 or UL 1795 and UL 1081and adopt all safety
measures indicated in installation standards.
The unit must be properly earthed (grounded).
Connect the earthing (grounding) conductor to the
terminal with the marking.
Compare the frequency and mains voltage with the
name-plate data and connect the supply conductors
to the terminals in accordance with the appropriate
diagram inside the terminal box cover.
ATTENTION: never allow washers or other
metal parts to fall into the internal cable
opening between the terminal box and
stator. If this occurs, dismantle the motor to
recover the object which has fallen inside.
The exible power supply cord must be at least of the H05
RN-F or H05 VV-F type. For outdoor whirlpool or spas the
mains cable must be at least of the H07 RN-F type
with
section of cable not less than (par. 12.5 TAB 1).
All the electrical components must be located outside
the reach of individuals who use the pool and must be
positioned or attached without any risk of their falling
into the bathtub.
Make electric bonding connections.
Connect only to a circuit protected by a ground-fault
circuit-interrupter with a rated residual operating
current I∆N not exceeding 30 mA.
Install a device for disconnection from the mains
(switch) with a contact separation of at least 3 mm in
all poles.
With a three-phase motor install an overload protection
device with curve D appropriate for the rated current
of the pump.
Single-phase SPAM, are supplied with a capacitor
connected to the terminals and (for 220-240 V - 50 Hz)
with an incorporated thermal protector.
7. STARTUP AND OPERATION
7.1. Preliminary checks before start-up of the
pump
Do not start-up the device in case of damaged parts.
7.2. First starting
OFF
ATTENTION: never run the pump dry, not even for
a short trial run.
Start the pump when the bathtub has been lled.
Stop the pump before the bathtub is drained.
To avoid damage to the pump due to prolonged
operation in a no-water situation make sure the
installed unit has level detectors or sensors to impede
starting and to provide automatic stopping if there is no
water in the bathtub or install a timer to protect against
the risk of prolonged accidental operation.
At rst start-up or following a long idle period,
check that the shaft turns by hand.
For this purpose use the screwdriver notch on the shaft
end ventilation side. Turn the shaft by hand only in the
direction indicated by the arrows on the pump casing.
Note that a slight degree of resistence to rotation is
normal; this is due to friction caused by the mechanical
seal.
The pump might be jammed by an obstruction, foreign
matter, sticking of mechanical seal surfaces or other
causes.
If the shaft cannot be freed by hand, the pump will
have to be dismantled and cleaned.
With three-phase motors check the direction of
rotation.
Do not start the motor if the shaft is jammed. If
jammed, the impeller may unscrew should the
motor start rotating backwards. Reverse rotation
can also damage the mechanical seal.
Momentarily start the motor to make sure pump
shaft rotation corresponds to the direction indicated by
the arrows on the pump casing: rotation is clockwise
when viewing the shaft from the fan end.
Otherwise, disconnect electrical power and reverse
the connections of two phases.
Never drop or insert any object into any opening.
Do not operate this unit without the guard over the
suction tting.
7.3. Switch off of the pump
ON
The appliance must be switch off every time
there are faults. (see troubleshooting).
The product is designed for a continuous duty, the
switch off is performed by disconnecting the power
supply by means the expected disconnecting devices.
(see paragraph “6.5 Electrical connection”).
8. MAINTENANCE
Before any operations it's necessary to disconnect the
power supply.
If required ask to an electrician or to an expert
technician.
Every maintenance operations, cleaning or
reparation executed with the electrical system
under voltage, it could cause serious injuries
to people.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualied persons in order to avoid
a hazard.
In case of extraordinary maintenance, or maintenance
operations that require part-removing, the operator
must be a qualied technician able to read schemes
and drawings.
It is suggest to register all maintenance operation
executed.
i
During maintenance keep particular attention in
order to avoid the introduction of small external
parts, that could compromise the device safety.
It is forbidden to execute any operations with
the direct use of hands. Use water-resistant,
anti-cut gloves to disassemble and clean the
lter or in other particular cases.
i
During maintenance operations external
personnel is not allowed.
Maintenance operations that are not described in
this manual must be made only by special personnel
authorized by Bedu Pompen BV
For further technical information regarding the use or
the maintenance of the device, contact Bedu
8.1.
Routine maintenance
OFF
Before every maintenance operations
disconnect the power supply and make sure
that the device could not accidentally operate.
SPA Rev7.indd 11 08/02/19 17:46

GB
Page 12 / 28 SPA Rev7 - Operating Instructions
Clean the lter inserted in the bathtub suction opening
at regular intervals.
The pump does not require servicing except for
disassembly for cleaning and removal of any
obstruction from inner parts and the draining hole
when, with use and in the course of time, performance
or self-draining capacity are found to be reduced.
Avoid cleaning an installed pump by hosing down
directly with jets of water without protection panels on
the bathtub.
Following a long idle period, check that the shaft
turns by hand.
For this purpose use the screwdriver notch on the shaft
end ventilation side. Turn the shaft by hand only in the
direction indicated by the arrows on the pump casing.
Note that a slight degree of resistence to rotation is
normal; this is due to friction caused by the mechanical
seal.
The pump might be jammed by an obstruction, foreign
matter, sticking of mechanical seal surfaces or other
causes.
If the shaft cannot be freed by hand, the pump will
have to be dismantled and cleaned.
8.2. Dismantling the pump
OFF
For dismantling and re-assembly see construction in
the cross-section drawing (page 14).
Remove the motor assembly with the lantern bracket
(32.00) from the pump casing (14.00), after removing
the screws (14.24), the nuts (14.28) and the washers
(14.29), levering them out with two screwsdrivers in
diametrically opposed positions.
To remove the impeller (28.00) insert a large straight-
blade screwdriver in the slot on the shaft (78.00) at the
ventilation end. Grip the impeller with one hand and
unscrew it, turning the shaft counter-clockwise and
twisting with both hands (g. 3a).
Fig. 3 Dismantling (a) and remounting (b) the impeller
If it is not possible to hold or move the shaft with the
screwdriver, remove the fan cover (90.00) and motor
fan (88.00) and unscrew the impeller by gripping the
shaft with a suitable wrench.
With the impeller the rotating part of the mechanical
seal (36.00) will remove.
8.3. Re-assembly
To replace the mechanical seal (36.00) t the rotating
part over the impeller hub (28.00) and push the
spring right down as far as the front shoulder. In this
way, correct spring compression will be ensured in
subsequent assembly.
Lubricate the seal with water and align the impeller on
the motor shaft.
ATTENTION: with the three-phase models, to avoid
the unscrewing (and breaking) of the impeller should
the motor start rotating backwards, clean the threaded
shaft end and apply on the rst half of the threaded part
Loctite 638 (to avoid unscrewing due to the resistant-
force of the water in the case of a backward rotation).
Grip the impeller with one hand and turn the shaft with
a screwdriver in the clockwise direction until tight.
With this operation the front surfaces of the mechanical
seal come into contact without rubbing against each
other during tightening.
Clean the O-ring (14.20) and seal surfaces with water.
When replacing the motor assembly with the impeller,
be careful to insert the locating lug inside the pump
casing (14.00) into the locating slot on the diffuser
cover (27.00).
9. DISPOSAL
OFF European Directive
2012/19/EU (WEEE)
The nal disposal of the device must be done by
specialized company.
Make sure the specialized company follows the
classication of the material parts for the separation.
Observe the local regulations and dispose the device
accordingly with the international rules for environment
protection.
10. SPARE PARTS
10.1. Spare-parts request
When ordering spare parts, please quote their
designation, position number in the cross section
drawing and rated data from the pump name plate
(type, date and serial number).
The spare parts request shall be sent to Bedu
Pompen by phone, fax, e-mail.
11. ESIGNATION OF PARTS
Nr. Designation
14.00 Pump casing
14.20 O-ring
14.24 Screw
14.28 Nut
14.29 Washer
27.00 Diffuser cover
27.04 Diffuser wall
27.08 O-ring
28.00 Impeller
36.00 Mechanical seal
70.00 Lantern bracket
73.00 Ball bearing
73.08 V-ring
76.00 Motor casing with winding
76.04 Cable gland
76.16 Support
76.54 Terminal board
78.00 Shaft with rotor packet
81.00 Ball bearing
81.04 V-ring
82.00 Motor end shield
82.04 Compensating spring
88.00 Motor fan
90.00 Fan cover
90.04 Screw
92.00 Tie-bolt
94.00 Capacitor
94.02 Capacitor gland
98.00 Terminal box cover
98.04 Screw
98.08 Gasket
Changes reserved.
SPA Rev7.indd 12 08/02/19 17:46

GB
SPA Rev7 - Operating Instructions Page 13 / 28
12. TROUBLESHOOTING
OFF
WARNING: Turn off the power supply before performing any operations.
Do not allow the pump or motor to run when dry even for a short period.
Strictly follow the user instructions and if necessary contact an authorised service centre.
PROBLEM PROBABLE CAUSES POSSIBLE REMEDIES
1)
The motor does
not start
1a) Unsuitable power supply
1b) Incorrect electrical connections
1c) Engine overload protective device cuts
in.
1d) Blown or defective fuses
1e) Shaft blocked
1f) If the above causes have already
been checked, the engine may be
malfunctioning
1a) Check that the mains frequency and voltage correspond to the
electrical characteristics shown on the indicator plate
1b) Connect the power supply cable to the terminal board correctly. Check
that the thermal overload protection is set correctly (see data on the
engine indicator plate) and make sure that the fuseboard upline of the
engine has been properly connected
1c) Check the power supply and make sure that the pump shaft is turning
freely. Check that the thermal overload protection has been set
correctly (see engine indicator plate)
1d)
Replace the fuses, check the electric power supply and points a) and c)
1e) Remove the cause of blockage as indicated in the “Blocked pump”
instruction booklet
1f) Repair or replace the engine by applying to an authorised service
centre
2)
Pump blocked 2a) Prolonged periods of inactivity with formation of rust inside the pump
2b) Presence of solid bodies in the pump
rotor
2c) Bearings siezed
2a) Rotation may be started directly from the pump shaft or from the
joint (remember to turn off the electricity supply rst ) or contact an
authorised service centre
2b) If possible, dismantle the pump casing and remove any solid foreign
bodies inside the rotor, if necessary contact an authorised service
centre
2c) If the bearings are damaged replace them or if necessary contact an
authorised service centre
3)
The pump
functions
but no water
comes out
3a) Possible inltration of air from suction
tube connections, drain plugs or lling
of pump or from the gaskets of the
suction pipe
3b) Foot valve blocked or suction pipe not
fully immersed in liquid
3c) Suction lter blocked
3a) Check which part is not tight and seal the connection adequately
3b) Clean or replace the bottom valve and use a suction pipe suitable for
the application
3c) Clean the lter, if necessary, replace it . See point 2a) also.
4)
Insufcient ow 4a) Pipes and accessories with diameter too small causing excessive loss of
head
4b) Presence of deposits or solid bodies in
the internal passages of the rotor
4c) Rotor deteriorated
4d) Worn rotor and pump case
4e) Excessive viscosity of the liquid
pumped (if other than water)
4f) Incorrect direction of rotation
4g) Suction head excessive in relation to
the suction capacity of pump
4h) Suction pipe too long
4a) Use pipes and accessories suitable for the specic application
4b) Clean the rotor and install a suction lter to prevent other foreign
bodies from entering
4c) Replace the rotor, if necessary, contact an authorised service centre
4d) Replace the rotor and the pump casing
4e) The pump is unsuitable
4f) Invert the electrical connections on the terminal board or control panel
4g) Try to close the feeder gate partially and/or reduce the difference in
level of the pump and the liquid being aspirated
4h) Bring the pump closer to the suction tank so as to use a shorter pipe.
If necessary use a pipe of a wider diameter
5)
Noise and
vibrations
from the pump
5a) Rotating part unbalanced
5b) Worn bearings
5c) Pump and pipes not rmly attached
5d) Flow too strong for the diameter of the
delivery pipe
5e) Functioning in cavitation
5f) Unbalanced power supply
5g) Incorrect alignment of pump-motor unit
5a) Check that no solid bodies are obstructing the rotor
5b) Replace the bearings
5c) Anchor the delivery and suction piping as needed
5d) Use bigger diameters or reduce the pump ow
5e) Reduce the ow by adjusting the feeder gate and/or using pipes with
a bigger internal diameter. See point 4g) too
5f) Check that the mains voltage is right
5g) If necessary, the unit must be re-aligned
6)
Leakage from
the mechanical
seal
6a) The mechanical seal has functioned
when dry or has stuck
6b) Mechanical seal scored by presence
of abrasive parts in the liquid pumped
6c) Mechanical seal unsuitable for the
type of application
6d) Slight initial drip during lling or on rst
start-up
In cases 6a), 6b) and 6c), replace the seal, if necessary contact an
authorised service centre
6a) Make sure that the pump casing (and the suction pipe if the pump is
not self-priming) are full of liquid and that all the air has been expelled.
See point 5 e) too.
6b) Install a suction lter and use a seal suited to the characteristics of the
liquid being pumped.
6c) Choose a seal with characteristics suitable for the specic application
6d)
Wait for the seal to adjust to the rotation of the shaft. If the problem
persists, see points 6a), 6b) or 6c) or contact an authorised service centre.
SPA Rev7.indd 13 08/02/19 17:46

26 / 28 SPA Rev7
12.4. Drawing for dismantling and assembly
3.94.036.1
28.12
4.94.011
4.94.012
92.00
3.94.056
90.04
81.04
82.00
98.04
94.02
94.00
76.04
76.54
98.00
98.08
70.00
14.20
27.00
28.00
27.08
14.00
90.00
88.00
82.04
81.00
76.16
92.00
78.00
76.00
73.00
73.08
36.00
14.24
14.29
14.28
27.04
76.50
70.00
14.20
27.00
28.00
27.08
14.00
36.00
14.24
14.29
14.28
27.04
98.04
94.00
98.08
98.00
76.54
76.04 90.00
90.04
76.00
70.20
73.08
82.04
81.00
78.00
73.00 81.04
82.00 88.00
82.08
76.50
(1)
Draining hole
ДÂ̇ÊÌÓ ÓÚ‚ÂÒÚËÂ
SPA 11
SPA 11, 21/A, 31/A
SPA 41
SPA Rev7.indd 26 08/02/19 17:46

SPA Rev7 27 / 28
12.5. Minimum cross-sectional area of conductors
Tab. 1 TAB 1IEC 60335-1
mm 2
Corrente nominale dell'apparecchio
Rated current of appliance
A
Corriente nominal del aparato
Dimensiestroom van apparaat
Номинальный ток прибора
设备额定运行电流
Sezione nominale
Nominal cross-sectional area
Nominal cross-sectional area
Nominale dwarsdoorsnede
Номинальное сечение
导体额定截面积
>3
>6
>10
>16
>25
>32
>40
0,75
1,0
1,5
2,5
4
6
10
≤6
≤10
≤16
≤25
≤32
≤40
≤63
÷
÷
÷
÷
÷
÷
÷
SPA Rev7.indd 27 08/02/19 17:46

EC – Declaration of Conformity
Manufacturer Details
Tradename
Bedu Pompen BV
Ad
d
res
s
Poort van Midden Gelderland Rood 10, 6666 LT, Heteren, Ne
therlands
Product Details
Product Na
me
Centrifugal pumps
Model (+series) Name
SPA series
Applicable Standards Details
Directives
2006/42/EC (Machinery Directive)
2014/35/EU (Low Voltage Directive)
2014/30/EU (Electromagnetic compatibility)
Standards
EN-ISO 12100:2010
EN-IEC 60204-1:2006
EN 809+A1/C1
Additional
informati
on
No further details.
Declaration
We hereby declare under our sole responsibility
that the product(s) mentioned above to which this
declaration relates complies with the above
mentioned standards and Directives.
BEDU Pompen BV
Poort van Midden Gelderland Rood 10
6666 LT Heteren
Tel : +31 (0)88 – 4802 900
Fax : +31 (0)88 – 4802 901
E-mail : [email protected]
Website : www.bedu.eu
Business Unit Manager:
Issued Date
:
01/10/ 2014
Marco Breunissen
Signature of representative(s)

Expert advice
A customer-oriented organization
that adapts to the requirements and
wishes of your organization
Innovative and customized solutions
Breakdownservice, 24 hours a day, 7
days a week
Technical service with extensive test
facilities, working from our own
workplace or at your location
A fast and appropriate solution for
all your issues
Wide range of liquid pumps
Repair, maintenance and revision
made for your process
BEDU POMPEN B.V.
Poort van Midden Gelderland Rood 10
6666 LT HETEREN
Nederland
Telefoon [phone]
E-mail [e-mail]
WWW.BEDU.EU
BEDU BELGIUM B.V.B.A.
Industriepark-West 75
9100 SINT-NIKLAAS
België
Telefoon [phone]
E-mail [email protected]
WWW.BEDU.BE