Beghelli 86 Series User manual

Mounting instructions
230V/50Hz
Series 86 Atomic
Sheet No.: 1494.0457
Stock item: E09060366
BEGHELLI - ELPLAST, a.s.
Poříčí 3A, 603 16 Brno - CZ
Tel: [phone]
Fax: [phone]
[email protected], www.beghelli.cz
No.1
Ø6
Ø6
L - LENGTH INCLUDING ENDINGS
X
13) CLUTCH ASSEMBLY
X - ONLY FOR SURFACE MOUNTED VERSIONS
X
61
61
61
61
61
61
61
61
MOUNTING PROCEDURE
DIMENSIONS
1
2
14) CONNECTION FRAME
2
1
1) REMOVING REFLECTOR
12
TYPE:
86-***/114
86-***/124
86-***/121
86-***/139
86-***/128
86-***/154
86-***/135
86-***/180
L1
580
580
880
880
1180
1180
1480
1480
HOLES No.2
FOR THE CONNECTING WIRES
2
1
2) PREPARATION OF A SCREW AND DIST.
INSERTIONS
L1
50 505026
A
480
480
780
780
3) MOUNTING HOLES
1
2
4) PREPARATION OF CONNECTING PART 6) FITTING COUPLING PART TO PROFILE
2 1
1
23
8) ASSEMBLY OF HINGE ON LUMINAIRE
TYPE:
86-003/114
86-003/124
86-003/121
86-003/139
86-003/128
86-003/154
86-003/135
86-003/180
L
583
583
883
883
1183
1183
1483
1483
60
B
60
60
60
60
60
60
60
56
H
56
56
56
56
56
56
56
B
H
L
10) ASSEMBLY OF RECESSED FRAME
1
2
11) MOUNTING OF ENDING
TYPE:
86-***/114
86-***/124
86-***/121
86-***/139
86-***/128
86-***/154
86-***/135
86-***/180
L2
588
588
888
888
1188
1188
1488
1488
Y
68
9) MOUNTING HOLE
68
68
68
68
68
68
68
2
1
12) LUMINAIRE ASSEMBLY INTO RECESSED FRAME
L2
Y
(L1xN) + 8mm
N = NUMBER OF LUMINAIRES
7) LUMINAIRE CONNECTION WITH COUPLING
PART
2 1
2
1
5) MOUNTING OF ENDING
A
No.1
HOLES No.1 - FOR MOUNTING:
ON WALL/CEILING, SUSPENDED MOUNTING, MOUNTING ON RECESSED FRAME
HOLES No.1 DIAMETER
1080
1080
1380
1380
L1 - LENGTH EXCLUDING ENDINGS
MINIMUM MOUNTING DISTANCE BETWEEN
CEILING AND SOFFIT
IMAGE - 1 IMAGE - 2 IMAGE - 3 IMAGE - 4
H min 95mm
8-20mm

Mounting instructions
230V/50Hz
Series 86 Atomic
BEGHELLI - ELPLAST, a.s.
Poříčí 3A, 603 16 Brno - CZ
Tel: [phone]
Fax: [phone]
[email protected], www.beghelli.cz
MOUNTING PROCEDURE:
86-003 – CEILING MOUNTING (separate)
Remove the louvre/cover (see IMAGE-1) and the reector (Fig.1) from the luminaire. Lead the wire through the hole for the cable. Prepare the screw and the insertion
(Fig.2). Attach the luminaire with screws into pre-drilled holes (Fig.3) and connect the cables to the terminal located on the beam. Assembly the reector in reverse
order than shown in the Fig.1. Place the lamps T5 into the sleeves and mount back the louvre/cover (see IMAGE-2).
86-013 – CEILING MOUNTING (coupling in lines)
Remove the louvre/cover (see IMAGE-1) and the reector (Fig.1) from the luminaire. Then prepare the clutch (Fig.4) and assembly the ending 99-0101 on the rst and
the last luminaire in the line (Fig.5). Then assembly the clutch into prole (Fig.6). Pass the wire through the hole. Prepare the screw and the insertion (Fig.2). Attach
the luminaires with screws into pre-drilled holes (Fig.3) and connect them to each other (Fig.7). Lead the power cable to the terminal box located on the beam and
then interconnect all the luminaires with wire required length and corresponding cross-section. Assembly the reector in reverse order than shown in the Fig.1. Place
the lamps T5 into the sleeves and mount back the louvre/cover (see IMAGE-2).
86-003 – PENDANT MOUNTING (separate)
Remove the louvre/cover (see IMAGE-1) and the reector (Fig.1) from the luminaire. Assembly the pendant 99-0085 into pre-drilled holes (Fig.3). Attach the luminaire
to pendant 99-0085 with screws M4 (Fig.8). Lead the power cable the hole and connect it to the terminal block located on the beam. Assembly the reector in reverse
order than shown in the Fig.1. Place the lamps T5 into the sleeves and mount back the louvre/cover (see IMAGE-2).
86-013 – PENDANT MOUNTING (coupling in lines)
Remove the louvre/cover (see IMAGE-1) and the reector (Fig.1) from the luminaire. Then prepare the clutch (Fig.4) and assembly the ending 99-0101 on the rst and
the last luminaire in the line (Fig.5). Then assembly the clutch into prole (Fig.6). Assembly pendants 99-0096 into pre-drilled holes (Fig.3). Attach the luminaires to
pendant 99-0096 by screws M4 (Fig.8) and connect them to each other (Fig.7). Pass the wire 99-0094 or 99-0095 through the hole and plug in the terminal box
located on the beam. Then interconnect all the luminaires with wire required length and corresponding cross-section. Assembly the reector in reverse order than
shown in the Fig.1. Place the lamps T5 into the sleeves and mount back the louvre/cover (see IMAGE-2).
86-023 – RECESSED MOUNTING (separate)
Remove the louvre/cover (see IMAGE-1) and the reector (Fig.1) from the luminaire. Attach the recessed frame (Fig.10) into mounting hole (Fig.9) and then expand
the springs by tightening the screw in the frame. Attach endings for recessed mounting 99-0102 (Fig.11). Pass the wire through the hole and attach the luminaire to
the frame by tightening screws M4 (Fig.12). Lead the power cable through the hole and connect it to the terminal block located on the beam. Assembly the reector
in reverse order than shown in the Fig.1. Place the lamps T5 into the sleeves and mount back the louvre/cover (see IMAGE-2).
86-033 – RECESSED MOUNTING (coupling in lines)
Remove the louvre/cover (see IMAGE-1) and the reector (Fig.1) from the luminaire. Fit and tighten the coupling on the embedded frame (Fig.13). Attach the rece-
ssed frame (Fig.10) into mounting hole (Fig.9) and then connect both frames by clutch (Fig.14). Expand the springs by tightening the screw in the frame. Then prepare
the clutch (Fig.4) and assembly into prole (Fig.6). Assembly the ending 99-0102 on the rst and the last luminaire in the line (Fig.11). Lead the power cable through
the hole. Then attach the luminaires into the frame by tightening screws M4 (Fig.12) and connect them (Fig.7). Plug the power cable into terminal box located on the
beam and interconnect all the luminaires with wire required length and corresponding cross-section. Assembly the reector in reverse order than shown in the Fig.1.
Place the lamps T5 into the sleeves and mount back the louvre/cover (see IMAGE-2).
For handling louvre and reector use enclosed gloves.
TECHNICAL DETAILS:
• Rated voltage: 230V, 50Hz
• Light source: linear uorescent lamp T5
• Degree of protection: IP 20
• Electrical accident protection class: I
• Suitable for direct mounting onto a normally inammable basis - F: yes
• The luminaire satises requirements of all standards in force
WARNING:
• Check whether the mains specication satises the data mentioned on a luminaire plate before connecting it to the mains.
• Contact the customer service authorised centre for replacement of uorescent tubes and batteries and for repairs, and insist on using original spare parts only. Not
satisfying these instructions could result in loss of luminaire safety or in loss of warranty.
• This luminaire should only be used for a purpose for which it was manufactured. Any other usage shall be assumed to be unsuitable and therefore dangerous. The
manufacturer bears no responsibility for any injury caused to persons or animals or for property damages caused by improper, faulty or inadequate usage.
• A luminaire must be disconnected from the mains before any interference with a luminaire, service or maintenance. An expert person, in terms of valid regulations
concerning the competence to activities, should only perform these actions.
• The luminaire may only be connected to the mains, whose installation and protection satises standards in force.
WARRANTY:
All products of the company Beghelli - Elplast, a.s. are made of the highest quality materials, thoroughly tested and guaranteed by the manufacturer to be free of
defects in terms of existing legislative regulations. This warranty becomes invalid if mounting is not executed according to the instruction manual, the luminaire is
damaged or modied or repaired by an unauthorised service centre of the company Beghelli - Elplast, a.s.
The product cannot be disposed as unsorted municipal waste. It must be collected separately to prevent negative environmental impacts. In accordance with the
procedures of Directive 2002/96 and relevant national laws and regulations adopted pursuant to this Directive on the disposal of waste at the end
of the life cycle of the product, any violation is sanctioned by law. Please inform yourselfabout the local separate collection system for electrical and
electronic products.