Behringer ULTRA METAL UM300 User manual

ULTRA METAL UM300
Heavy Metal Distortion Eects Pedal
Thank you for showing your condence in us by purchasing the BEHRINGER ULTRA METAL UM300.
This high-quality eects pedal comes with a dual-gain circuitry that enables you to produce super thick,
tube-like distortion plus endless sustain. Thanks to its high-performance features you will achieve the
most extreme and sought-after hard rock or heavy metal distortion sounds.
1. Controls
(1) The LOW control allows yu to boost/cut the lo-frequency range.
◊
◊ Please keep in mind that extrme distortion and EQ settings will increase nose and may
induce oscillation.
(2) The two MID FREQ(uency) controls allow to boost/cut a dened mid-frequency range. The upper
control is used to increase or lower the mid range, the cntrol below adjusts the center frequency of
the mid range that is aected (200 Hz to 5 kHz).
(3) The LEVEL control adjusts the output level.
(4) The ON/BATT LED illumnates when the eect is activated. It also serves as a battery leve indicator.
(5) Use the footswitch to activate/deactivate the eect.
(6) Use this ¼" TS IN connector to plug in the instrument cable.
(7) The ¼" TS OUT connector sends the signal to your amp.
Use the DC IN connectionto plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V battery,
press the hinges with a ballpen and remove the pedal cover. Be careful not to scratch the unit.
◊
◊ The UM300 has no on/o switch. As soon as you insert the jack into the in connector,
the UM300 begins running. When not using the UM300, remove the jack from the
in connector. This extends the life of the battery.
The SERIAL NUMBER is located at the bottom.
(3)
(1) (5)
(4)
(7)
(2)
(8)
(6)
(9)

ULTRA METAL UM300
MUSIC Group accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and other information are subject to change without notice. All trademarks are the property
of their respective owners. MIDAS, KLARK TEKNIK,TURBOSOUND, BEHRINGER, BUGERA and DDA are trademarks or registered trademarks of MUSIC Group IP Ltd.
© MUSIC Group IP Ltd. 2015 All rights reserved.
2. Safety Instructions
Do not use near water, or install near heat sources. Use only authorized attachments/accessories.
Do not service product yourself. Contact our qualied servicing personnel for servicing or repairs,
especially when power supply cord or plug is damaged.
3. Warranty
Please register your new BEHRINGER equipment right after your purchase by visiting
http://behringer.com and read the terms and conditions of our warranty carefully.
4. Specications
In
Connector ¼" TS
Impedance 500 kΩ
Out
Connector ¼" TS
Impedance 1 kΩ
Power Supply
9 V𝌂, 100 mA regulated
BEHRINGER PSU-SB
USA/Canada 120 V~, 60 Hz
U.K./Australia 240 V~, 50 Hz
China/Korea 220 V~, 50 Hz
Europe 230 V~, 50 Hz
Japan 100 V~, 50 - 60 Hz
Power connector 2 mm DC jack,
negative center
Battery 9 V type 6LR61
Power consumption 30 mA
Physical/Weight
Dimensions approx. 54 x 70 x 123 mm
(H x W x D) (2.1 x 2.8 x 4.8")
Weight approx. 0.33 kg (0.7 lbs)
BEHRINGER is constantly striving to maintain the
highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing
products without prior notice. Specifications and appearance
may therefore differ from those listed or shown.